2. Kamstrup
  3. IP201

Kamstrup IP201, IP201 Gateway Module Installation guide

  • Hello! I've reviewed the installation guide for the Kamstrup IP201 IP module. This document provides information on mounting, connection, configuration, and troubleshooting for the module. It details LED status indications, Ethernet connection, serial port usage, and the service button. I am ready to answer your questions about the IP201 module.
  • What does the Action diode indicate?
    What does the Wink diode indicate?
    What does the Err diode indicate?
Instlltion guide
IP201
Kmsrup A/S · Indusrivej 28, Silling · DK-8660 Sknderborg · T: +45 89 93 10 00 · info@kmsrup.com · kmsrup.com
2 Kmstrup A/S • 5512937_C1_GB_05.2017
IP201
Contents
1 Montge 3
2 Anschluss 3
3 Konfigurtion 3
4 Ethernet-Anschluss 4
5 Instlltion 5
6 Pltzierung von Leuchtdioden (Ausschnitt des Moduls) 6
7 Sttus-Leuchtdioden 6
7.1 Action 6
7.2 Wink 6
7.3 Err 6
7.4 Wrtungstste 7
8 Port B 7
9 Modulübersicht 7
3Kmstrup A/S • 5512937_C1_GB_05.2017
IP201
1 Mounting
Typiclly, the module is supplied mounted
directly in RF Concentrtor or similr
equipment.
Exmple of mounting in RF Concentrtor
2 Connection
The IP module hs no built-in encryption, nd therefore it should lwys be plced behind  firewll
or NAT (Network Address Trnsltion).
3 Configurtion
The IP201 module is lwys supplied configured with either defult IP settings or custom IP
settings. These settings cn be chnged subsequently by using IP Tool, which cn be obtined by
contcting Kmstrup.
It is possible to use either dynmic or sttic IP ddresses, nd it is possible to order with the
following settings:
Dynmic IP ddress (DCHP):
Host server nme (the DNS name or IP address of the server to which the unit must report back).
Sttic IP ddress:
IP ddress, subnet, gtewy (network settings of the module).
Host server (the IP address of the server to which the device must report back).
4 Kmstrup A/S • 5512937_C1_GB_05.2017
IP201
4 Ethernet connection
The Ethernet connection on IP201consists of  stndrd 4-pole screw terminl.
The terminl is connected ccording to the below tble for connection to hub, switch or router, etc.:
Terminl no. T-568B colour code Signl MCU
114 / 116 Ornge / White Ethernet Tx+ RE4, RE5
115 / 117 Ornge Ethernet Tx- RE6, RE7
116 / 114 Green / White Ethernet Rx+ RG5
117 / 115 Green Ethernet Rx- RG4
Termnil number.
Silk screen print on 5550844 rev. G.
For connection directly to PC (lso possible on hub, switch, etc. with uto sense of crossed
connection):
Terminl no. T-568B colour code
114 / 116 Green / White
115 / 117 Green
116 / 114 Ornge /
White
117 / 115 Ornge
Termnil number.
Silk screen print on 5550844 rev. G.
Ethernet connection
5Kmstrup A/S • 5512937_C1_GB_05.2017
IP201
5 Instlltion
When supply hs been estblished, the Err nd Wink diodes re lit to indicte tht the module is
switched on. The Link diode lights/flshes if the RJ45 cble is mounted (communiction on the
network is indicted by flshes).
During strt-up, the Err nd Wink diodes re used for controlling the stte of the module:
1 Err nd Wink emit light constntly: The module hs just strted.
2 The Wink diode turns off when the module hs estblished connection to the network (vlid IP).
3 The Err diode strts flshing when the host is recognised (meter or concentrtor hve been
detected).
4 The Err diode turns off when the module hs been registered by the collecting server.
If the module cnnot connect to the meter nd/or server, IP201 will restrt.
Strt-up ACT/LINK WINK ERR
Power UP Off On On
LAN connection On/flsh - -
~3 sec (depending on DHCP srv), ~0 sec if sttic IP is used.
Vlid IP On/flsh Off On
15-20 sec.
Host recognised (meter/conc) On/flsh Off Flsh
20 sec (depending on AMR system).
Ack from server On/flsh Off Off
Ethernet connection ACT/LINK WINK ERR
No Ethernet Off – –
LAN OK – idle On – –
LAN OK –dt ctivity Flsh – –
6 Kmstrup A/S • 5512937_C1_GB_05.2017
IP201
6 Locliztion of light-emitting diodes (extrct of the module)
Action Wink Error
7 Sttus LEDs
The module hs  number of light-emitting diodes. They re used for indicting the sttus nd
service.
7.1 Action
The Action diode indictes network ctivity. During norml opertion, this diode lights/flshes.
Turned off: The module does not connect to the network. Check tht the cble is
connected correctly.
Flshing: Dt is detected on the network. (the fster the flshing, the more trffic).
Stedy light: The module is connected, but there is no trffic on the network.
7.2 Wink
The Wink diode is used for indicting the module’s conditions in three situtions:
Strt-up: The Wink diode is lit until  vlid IP ddress is found.
Locliztion: The Wink diode flshes.
Service: By pressing the service button, the Wink diode is lit. The Wink diode is lit while
the module is in service mode.
7.3 Err
The Err diode is used for indicting irregulrities.
Stedy light: The module hs just strted nd is witing for n IP ddress.
Flshing: The module hs not yet recognised the unit in which it is mounted (the host)
Turned off: Norml sitution.
7Kmstrup A/S • 5512937_C1_GB_05.2017
IP201
7.4 The service button
The service button is used by Kmstrup in connection with service nd reprogrmming of the
module.
8 Port B
Port B is  seril (RS232/Kmstrup 3-wire) connection tht cn be used for connecting dditionl
externl equipment.
For instnce:
• Connection of dditionl RF concentrtor
Port B is lwys configured for 9600,8,N,1.
9 Module overview
Ethernet
connection
Port B:
Seril connection of
dditionl equipment
Connection to
power supply
Service button
Action Wink Error
Kmstrup A/S • 5512937_C1_GB_05.2017
/