JasonL QDSR3618.W.WT Operating instructions

Type
Operating instructions

This manual is also suitable for

ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
Page 1 of 11
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Tools Required: Power screwdriver; Allen key set (provided)
2 persons required for installation
ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
Page 2 of 11
Need help!
Call us on
1300 527 665
www.jasonl.com.au
E
Table top x2
Table top Return x2
Legs Quadro Square x4
Legs Quadro Square Return x2
Connector frame x1
Beam: Main desk x2
Beam: Return x2
Plastic bracket x12
Joiner plates x4
A
B
C
D
E
F
G
H
I
Allen key x2O
M8x20MM CSK x6
M8x20MM Socket head x6
M6x20MM Socket head x12
M6x30MM Socket head x12
Join plates Screws
J
K
L
M
N
COMPONENTS
SCREWS
G
F
H
I
J K L M N
A
B
C
D
ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
Using Allen Key provided, attach 2 plastic brackets per leg
(C)(D) (as per picture above) using M6x20MM (L) Socket head
screw. Do the same with Connector frame (E).
Using Allen Key provided, attach M8x20MM Socket head (K)-
screw socket half way into leg for both legs (C) and into
Connector frame (E).Page 3 of 11
Need help!
Call us on
1300 527 665
www.jasonl.com.au
K
L
STEP 01 STEP 02
ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
STEP 03
Adjust extendable beam (F) to desired
length using markers and secure beam
at that length using screws provided
Page 4 of 11
Need help!
Call us on
1300 527 665
www.jasonl.com.au
50
1200
1300
1400
1500
1600
1700
1800
1900
2000
50
ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
Attach beam (F) to legs (C) and Connector frame (E)
using nut insert in legs. See point attached
Frame looks like this. Using Allen Key, attach beam (F) with Socket (J)
Page 5 of 11
Need help!
Call us on
1300 527 665
www.jasonl.com.au
STEP 05
J
J
J
J
STEP 04
TOP VIEW
J
G
D
STEP 06
Now attach the return beams (G) to return legs (D) using nut insert in legs. See point attached.
Then, connect the hook of the return beam to the beam of the main structure.
Page 6 of 11
ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
Need help!
Call us on
1300 527 665
www.jasonl.com.au
N
I
B
STEP 07
Page 7 of 11
Attach Connector Plates (I) to Return Top (B) by tightening Screws (N)
ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
Need help!
Call us on
1300 527 665
www.jasonl.com.au
STEP 8
Page 8 of 11
Place table tops (A) on top of frame - with cutout at the back of the desk.
Using nut inserts in the desk, use M6x30mm socket (M) and attach desktop to the frame.
Using nut inserts in the desktop, use M6x30mm socket (M) and attach return desktops (B) to the frame.
Once desktop are attached and secure to the frame, use woods screws (N) and secure joiner plates (I) to the underside of desktop A.
nut insert nut insert
TABLE TOP
BOTTOM VIEW
M
I
N
B
A
nut insertnut insert
ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
Need help!
Call us on
1300 527 665
www.jasonl.com.au
STEP 9
Page 9 of 11
Please leave 25mm gap between 2 x table top (A) so we can drop the return desk mounted screen in between the two tops.
Please position the screen so that it sits at the same level as the bottom surface of the desktop. Please adjust the screen
position to make sure the screen end meet with the the desk end and please hold the screen.
Second person to insert single desk mounted rod brackets. The brackets rod goes inside the pre-drilled screens holes.
The screen holes are located around 300mm from the screen end each. First person to hold screen stand still.
B
B
A
A
If you purchased
with screens divider
ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Page 10 of 11
STEP 10
Second person to drill 4 holes into the brackets holes with provided wood screws into the underneath desktop.
Please check the position of the rod brackets and bracket holes again before drilling the screws all the way
through. Please tighten all the wood screws.
side view
ASSEMBLY INSTRUCTIONS
Quadro Square leg 2 person
corner workstations
T configuration
Sizes: 1400Lx1800W , 1600Lx1800W , 1800Lx1800W mm
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Page 11 of 11
STEP 11
Using an Allen key remove top 3 caps from all screens uprights. Bring three partition towards one another and slide the 3 way
connector rod - down between the three screen uprights.
Under the desktops, use l-shaped panel brackets to secure the screens to the table tops (A). Place two brackets in each screen.
Floor based screen divider assembly instruction:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

JasonL QDSR3618.W.WT Operating instructions

Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI