Jason.L Blackjack LShaped Assembly Instructions Manual

Brand
Jason.L
Model
Blackjack LShaped
Type
Assembly Instructions Manual

Jason.L Blackjack LShaped is a sturdy and versatile desk designed to accommodate various office needs. It features an L-shaped configuration with a spacious main desktop and a return desktop, providing ample surface area for work and storage. The desk's sturdy construction ensures stability, while the adjustable feet allow for leveling on uneven surfaces. The included modesty panel adds privacy and a professional touch to the workspace. Assembly requires minimal tools and can be completed with the help of clear instructions and labeled components.

Jason.L Blackjack LShaped is a sturdy and versatile desk designed to accommodate various office needs. It features an L-shaped configuration with a spacious main desktop and a return desktop, providing ample surface area for work and storage. The desk's sturdy construction ensures stability, while the adjustable feet allow for leveling on uneven surfaces. The included modesty panel adds privacy and a professional touch to the workspace. Assembly requires minimal tools and can be completed with the help of clear instructions and labeled components.

Tools Required: Power screwdriver.
2 persons required for installation
Special Note: No pre-drilled holes or nut inserts are
provided. Wood screws will be required to be drilled
directly into underside of desk top.
Tools Required:
Power screwdriver.
Special Note:
No pre-drilled holes or nut inserts are
provided. Wood screws will be required to be drilled
directly into underside of desk top.
ASSEMBLY INSTRUCTIONS
Blackjack LShaped
Corner Executive Desk
Page 1 of 7
Need help!
Call us on
1300 527 665
www.jasonl.com.au
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
COMPONENTS
SCREWS
Page 2 of 7
Upper Wrist A x 2
Upper Wrist B x 1
Top Rail A x 1
Top Rail B x 1
Leg Tube x 3
Large Foot x 2
Small Foot x 4
4 Way Cross Collar x 3
Cross Collar Plug x 6
Main Desktop x 1
Return Desktop
4 Way Gasket x 3
Plastic Support x 3
Foot Gilde x 6
Joining Plate x 2
Top Rail Cap x 3
Modesty Panel x 1
Studio Small Bracket x 2
M10x30mm x 3
M10x110mm x 3
M8x16mm x 6
M5x25mm Self Tapping
M5x20mm Self Tapping
ASSEMBLY INSTRUCTIONS
Blackjack LShaped
Corner Executive Desk
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Tip: To prevent possible scratches or damage, assemble the Desk upside down on a
soft surface such as a blanket, carpet or packaging.
Tip: Attach Leg to the Top assembly by using Bolts, spring washer, flat washer. Tighten
using the Allen Wrench provided.
* The top of the leg tube has more rim
notches than the bottom of the leg tube.
03 04
01 02
Page 3 of 7
ASSEMBLY INSTRUCTIONS
Blackjack LShaped
Corner Executive Desk
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Sort the feet into pairs, two sets of one large & one small foot for the
main desk legs. One set of two small feet for the return leg.
Slide two feet and two cross collar plugs (9) into the 4 way cross collar
(8), place the 4 way gasket (12) on top and fully tighten the two
M8x16mm bolts (21) into the collar (8).
Screw all glides (14) into the base of the feet, leaving the glides one turn
from tight (then they can be adjusted easily if the floor is uneven).
Place a leg pole tube (5) on top of a collar. Align the notch. Fully tighten
the M10x110 bolt (20), spring washer and flat washer through the collars.
Repeat for all leg assemblies.
Page 4 of 7
ASSEMBLY INSTRUCTIONS
Blackjack LShaped
Corner Executive Desk
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Place the upper wrists on top of the leg tube, making sure each small
notch in the top of the leg tube is in-line with the bumps on the bottom of
the upper wrist. Fully tighten to maximum tension the M10x30mm bolts (19).
Place each end of the top rail A (3) into the holes on the side of the upper
wrist A, making sure they stop level with outer edge of wrists. (It is permissible
in some applications for top rail to protrude out further past the wrists.)
Fully tighten the small screws located at the bottom of each upper wrist
to firmly hold the top rail in place.
Place the top rail cap (16) into the exposed ends of the top rail.
07 08
05 06
Main Desk LegReturn Desk Leg
Note: Choose both of the
main desk leg assembly.
Note: The largest wrist fits to
the narrowest leg assembly.
Page 5 of 7
ASSEMBLY INSTRUCTIONS
Blackjack LShaped
Corner Executive Desk
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Locate the plastic support bracket (13) over the centre of the top rail,
and click into place.
Optional: For extra strength, the plastic support bracket can be
screwed onto the top rails.
Choose if you want your return to be on user’s left hand (LH) return or
user’s right hand (RH) return. The next install diagrams 12 to 20 have the
tops turned upside down on th floor. Remember the LH or RH you chose
will reverse when the desktops are upside-down.
Place desktops upside-down, push tightly together. Position joining plates
(15) accoss each top then screw fix with M5x20mm screws (23). (Remem-
ber left hand and right hand will reverse when the tops assembly is
rotated correct way up from this upside-down position.
* Above shows RH configuration.
12
09 10
RH Return
LH Return
11
Page 6 of 7
ASSEMBLY INSTRUCTIONS
Blackjack LShaped
Corner Executive Desk
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Position frame on the main desktop as shown. Screw plastic support in
centre using M5x20mm screws (23), then screw the wrists into underside
of the main desktop using M5x25mm screws (22) .
Position the return leg assemly so wrist is 25mm from end of return.
Fix in place using M5 x 25 screws (22).
The return top rail is usually 1450mm length. Clip plastic supports 100mm
and 500mm from on end of this rail. Screw fix the end support.
Insert return top rail (4) into hole in wrist with plastic supports flat against
underside of dekstop. Stop the rail level with outer edge of wrist.
14
16
13
15
Page 7 of 7
ASSEMBLY INSTRUCTIONS
Blackjack LShaped
Corner Executive Desk
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Place the top rail cap (6) into the exposed side end of the top rail. Fully
tighten the small screws located at the bottom of each upper wrist to
firmly hold the top rail in place.
Fix the plastic supports into underside of return desktop using
M5x20 screws (23).
Position Studio small brackets (18) on the modesty (17), fix in place using
M5x15mm screws.
Place the modesty on the underside of main desktop, allow
50mm from the egde of desktop, fixing the modesty using
M5x20mm screws (23).
Modesty Panel
19 20
17 18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Jason.L Blackjack LShaped Assembly Instructions Manual

Brand
Jason.L
Model
Blackjack LShaped
Type
Assembly Instructions Manual

Jason.L Blackjack LShaped is a sturdy and versatile desk designed to accommodate various office needs. It features an L-shaped configuration with a spacious main desktop and a return desktop, providing ample surface area for work and storage. The desk's sturdy construction ensures stability, while the adjustable feet allow for leveling on uneven surfaces. The included modesty panel adds privacy and a professional touch to the workspace. Assembly requires minimal tools and can be completed with the help of clear instructions and labeled components.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents