ADTRAN TOTAL ACCESS 4303 OCTAL DSX-1 Job Aid

ADTRAN
Brand
ADTRAN
Model
TOTAL ACCESS 4303 OCTAL DSX-1
Type
Job Aid
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
Total Access 4303
Octal DSX-1
P/N: 1202332L1
CLEI: SII3VX5J_ _
Total Access 4303 Octal DSX-1 Module with ISDN Support
ONLINE
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
OCTAL
DSX-1
1202332L1
*61202332L1-22C*
3. The Total Access 4303 SCU automatically detects the presence of the module. No
need to reboot.
4. Once installed, use the terminal menus to configure and control the Octal DSX-1
Module. For more information, refer to the SCU Job Aid.
5. Use the arrow keys on the VT100 terminal keyboard to move to the
Modules menu,
and press
ENTER in the Menu column of the appropriate module.
SPECIFICATIONS
COMPLIANCE
The Total Access 4303 Octal DSX-1 Module is NRTL listed to the applicable UL
standards. The Octal DSX-1 Module is to be installed in a restricted access location and
in a Type “B” or “E” enclosure only.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by ADTRAN could void the user’s
authority to operate this equipment.
Specifications
Framing ESF, SF (D4)
Line Coding AMI (alternate mark inversion)
B8ZS (bipolar 8 zero substitution)
Line Build Out 0 to 655 feet in 133-foot increments
Tests Self-test
Local Line and Payload Loopbacks
Remote Line and Payload Loopbacks
Line Rate
ISDN Support
1.544 Mbps ± 50 bps
4:1 TDM Mapping to 3DS0 (TR397) Frame Format
Terminating Impedance 100 ohms ± 5%
Power 8.40 watts
Compliance FCC Part 15, UL 60950, NEBS Level 3
Temperature Operation: –5ºC to +70ºC
Storage: –40ºC to +70ºC
Relative Humidity To 95% noncondensing
Code Input Output
Power Code (PC) C C
Telecommunication Code (TC) – –
Installation Code (IC) A –
FRONT PANEL LEDS
ONLINE ! Off ............................... Blown fuse or no power supplied to the shelf
" Green ........................... Online
4 Flashing Green ............ Offline
" Amber.......................... Self-test in progress
4 Flashing Amber ........... Firmware upgrade in progress
" Red .............................. Module failure
4 Flashing Red................ Self-test failure
CH1-CH8 ! Off ............................... DSX-1 not configured for use
" Green ........................... DSX-1 signal present and synchronized and chan-
nel is configured for use
" Amber.......................... DSX-1 test in progress (includes port self-test)
4 Flashing Red................ Errors occurring on channel (BPV or Frame Loss)
(Momentarily)
INSTALLATION
After unpacking the Total Access
®
4303 Octal DSX-1 Module, inspect it for damage. If
damage has occurred, file a claim with the carrier, then contact ADTRAN Customer
Service.
Warranty information can be found online at www.adtran.com/warranty. To
install the Octal DSX-1 Module
, perform the following steps:
NOTE: Hot insertion of the Octal DSX-1 Module is permissible.
1. Insert the Octal DSX-1 Module into the desired slot labeled
1 through 16.
2. The Octal DSX-1 Module connects to a pair of 64-pin amphenol connectors on the
Total Access 4303 backplane (see table below).
Amphenol Connector Port Assignment
Slot Connector
Pins
Ring (ch 1-8) Tip (ch 1-8)
Slot 1 TX1, RX1 1 - 8 33 - 40
Slot 2 TX1, RX1 9 - 16 41 - 48
Slot 3 TX1, RX1 17 - 24 49 - 56
Slot 4 TX1, RX1 25 - 32 57 - 64
Slot 5 TX2, RX2 1 - 8 33 - 40
Slot 6 TX2, RX2 9 - 16 41 - 48
Slot 7 TX2, RX2 17 - 24 49 - 56
Slot 8 TX2, RX2 25 - 32 57 - 64
Slot 9 TX3, RX3 1 - 8 33 - 40
Slot 10 TX3, RX3 9 - 16 41 - 48
Slot 11 TX3, RX3 17 - 24 49 - 56
Slot 12 TX3, RX3 25 - 32 57 - 64
Slot 13 TX4, RX4 1 - 8 33 - 40
Slot 14 TX4, RX4 9 - 16 41 - 48
Slot 15 TX4, RX4 17 - 24 49 - 56
Slot 16 TX4, RX4 25 - 32 57 - 64
61202332L1-22C
0502
PRICING AND AVAILABILITY 800.827.0807
TECH SUPPORT 800.726.8663
RETURN FOR REPAIR 256.963.8722
www.adtran.com
61202332L1-22C
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service.
Warranty information can be found online at www.adtran.com/warranty
.
Total Access 4303 Octal DSX-1 Module with ISDN Support
MENU TREE FOR THE OCTAL DSX-1 MODULE WITH ISDN SUPPORT
Part Number
Serial Number
CLEI Code
Board Revision
PLL Status
DSX Info
Total Access 4303
Module Menu
H
[Prt]
Port Name
State
DS1 Configuration
Auto
Auto BER
IS
IS AS
OOS
None
2E-7
• • •
9E-7
1E-6
• • •
7E-6
Frame Format
OSS Threshold
IS Threshold
D4
ESF
Auto TX Yellow Alarm
Transmit PRMs
Off
On
Remote Device
Accept
Ignore
Loopback Accept
Disabled
ADTRAN
Type 1
Type 2
Line Code
AMI
B8ZS
Line Build Out
0 dB
266FT DSX1
399FT DSX1
533FT DSX1
655FT DSX1
Off
On
Pulse Density Enforcer
H1
DS1 Alarms & Status
[Prt]
Clear Results <+>
Errored Seconds
Bursty Errored Seconds
Severely Errored Seconds
Severely Errored Frame Secs
Loss of Frame Count
Controlled Slip Seconds
Unavailable Seconds
Line Code Violations
Path Code Violations
Line Errored Seconds
Degraded Minutes
Test Pattern
Test Status
Pattern Status Clear <+>
Pattern Error Inject <+>
DS1 Test
3DS0 Rsrc Usage
DS1 Perf Curr
DS1 Perf 15 Min
DS1 Perf 24 Hr
DS0 Alarms
DS0 Configuratiion
DS0 Map Status
[Prt]
Alarms
Status
BER
DS1 Signal Status
[Prt]
Rx
Tx
None
Line
Payload
[Prt]
Local Loopback
Remote Loopback
None
All Ones
All Zeros
QRSS
QRSS 56k
DALY
3-IN-24
1-IN-8
2-IN-8
[Prt]
DS0 Config
DS0 Not Used Count
[N]
CLR <+>
Usage
NEBE
FEBE
Sync
H1
None
ATT Inband
ANSI FDL Line
ANSI FDL Pyld
NIU Inband
  • Page 1 1
  • Page 2 2

ADTRAN TOTAL ACCESS 4303 OCTAL DSX-1 Job Aid

ADTRAN
Brand
ADTRAN
Model
TOTAL ACCESS 4303 OCTAL DSX-1
Type
Job Aid
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents