QualGear QG-DM-01-022 Operating instructions

Brand
QualGear
Model
QG-DM-01-022
Category
Flat panel desk mounts
Type
Operating instructions

QualGear QG-DM-01-022 is a 3-WAY ARTICULATING SINGLE MONITOR DESK MOUNT that has a weight capacity of 8kg (17.6lbs). It is designed to be installed on the edge of your desk or through a grommet hole. The mount allows you to tilt, swivel, and rotate your monitor to find the perfect viewing angle. It also comes with a cable clip to help you keep your cables organized.

Here are some of the benefits of using the QualGear QG-DM-01-022:

  • Improved ergonomics: The mount can help you to improve your posture and reduce neck and eye strain by allowing you to position your monitor at the optimal height and angle.

QualGear QG-DM-01-022 is a 3-WAY ARTICULATING SINGLE MONITOR DESK MOUNT that has a weight capacity of 8kg (17.6lbs). It is designed to be installed on the edge of your desk or through a grommet hole. The mount allows you to tilt, swivel, and rotate your monitor to find the perfect viewing angle. It also comes with a cable clip to help you keep your cables organized.

Here are some of the benefits of using the QualGear QG-DM-01-022:

  • Improved ergonomics: The mount can help you to improve your posture and reduce neck and eye strain by allowing you to position your monitor at the optimal height and angle.
6
CAUTION!
Do not exceed the maximum rated weight
specified. Otherwise, serious injury or
property damage may occur.
8kg
(17.6lbs)
RATED
QG-DM-01-022
3-WAY ARTICULATING SINGLE MONITOR DESK MOUNT
Scan the QR Code™ below
for more info about this product:
Product Dimensions
2713
27
Scan the QR Code™
below to contact us:
store.qualgear.com
google.com/+qualgear
youtube.com/qualgear
support@qualgear.com
facebook.com/qualgear
twitter.com/qualgear
pinterest.com/qualgearusa
+1 (972) 423-8960
Please check that the desk mount is secure and safe to use at regular intervals. If you have any questions
regarding any of the instructions or warnings; please contact your local distributor directly (OR) contact
QualGear technical support via email at [email protected].
Version May 2018Version May 2018
16"
17.7"
WARNING
Parts Checklist
Hardware Package
Desk Clamp
Assembly (x1)
C
Adapter Bracket
Assembly (x1)
A
Pole (x1)
B
M3x12mm (x4)
M-A
M4x12mm (x4)
M-B
M5x12mm (x4)
M-C
D3 Washer (x4)
M-D
D5 Washer (x4)
M-E
Pad (x1)
H
5mm Allen Key (x1)
I
6mm Allen Key (x1)
J
Cable Clip (x1)
D
Base Plate (x1)
E
M10x20mm (x1)
G
Silicone Pad (x5)
F
Please read the entire installation manual before you start assembly and installation.
NOTE
all
any
support
of
any
• Do not begin the installation of this product before you have read and understood
the instructions and warnings contained in this installation manual. If you have
questions regarding the instructions, please contact the reseller or QualGear
department via email at support@qualgear.com.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• Make sure that the supporting surface will safely support the combined weight
the equipment and all attached hardware and components.
• This product should only be installed by someone, who has good mechanical
ability with prior experience in installation and assembly of products and fully
understands this manual.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items. This greatly reduces their holding power.
• All QualGear products are intended for indoor use only and any outdoor use
voids
the limited warranty.
• All QualGear products are designed and tested for residential use only and
commercial use voids the limited warranty. For warranty information, please visit
qualgear.com/warranty.php.
IMPORTANT: Before starting installation, please check that all parts shown in this checklist
are included. If any parts are missing or damaged, contact your local distributor or
[email protected] for replacement parts and do not start assembly and installation
until you receive all the parts.
Min. Desktop Thickness = 10mm (0.39") / Max. Desktop Thickness = 88mm (3.46")
NOTE
Insert security pin of
desk clamp assembly (C) in
one of the small two holes of
pole (B) to center align them.
NOTE
Insert security pin of
desk clamp assembly (C) in
one of the small two holes of
pole (B) to center align them.
NOTE
Min. Hole Diameter = 10mm (0.39") / Max. Hole Diameter = 75mm (2.95")
NOTE
10-88mm
1
1
3
2 3
Attach the desk clamp assembly (C)
to the pole (B) with a M10x20mm
screw (G) and tighten the screw using
a 6mm Allen key (J). Peel backing
from the silicon pads (F) and
attach to the desk clamp.
For grommet installation,
disassemble the desk clamp (C) and
select the right parts.
Peel backing from the silicon pads (F)
and attach to the base plate (E).
Insert the adjust screw into
the base plate (E) through the hole and
pad (H). Then tighten the adjust screw
to hold the mount securely.
J
G
C
C
E
H
F
B
B
• Determine the mounting location, and then place the desk mount over the edge of the desk so that
the clamp fully contacts the desk edge.
• Turn the knob to make clamp fit to the desk edge, then secure it tightly.
10-75mm
Pole
Pole
Pad
Desk Clamp
Assembly
Desk Clamp
Assembly
6mm Allen Key
M10x20mm screw
Silicone
Pads
2
E
F
Silicone Pads
Base Plate
Base Plate
Hole
1a
Edge Installation
1b
Grommet Installation
1
2
3
2
Lift the display and make
the screws on the display
fit into the slots on the
VESA plate.
Attach the screws for the
top two holes on the back
of your display.
Tighten them using a Philips
screwdriver leaving a 3mm
clearance.
Insert the cable clip (D) first and then the adapter bracket assembly (A) into the pole (B) at a desired height.
Tighten the screw with a 5mm Alley key (I) to secure the adapter bracket assembly.
A
B
D
I
Adapter Bracket
Assembly
Pole
Cable Clip
5mm
Allen Key
HEAVY!
You may need assistance with this step.
3mm
1
Choose appropriate screws
and washers according to your
display.
M-A
M-D
M-B
M-C
M-E
OR
2
Installing The Adapter Bracket Assembly
3a
Attaching The Display (For VESA 100x100mm)
yalpsid eht fo kcaB
4
Install both screws through the lower mounting holes on the VESA plate into the display.
Tighten all screws but do not over tighten.
WARNING
Install all four screws through the inner mounting holes on the VESA plate into the display.
Tighten all screws but do not over tighten.
WARNING
M-B
M-C
M-E
M-A
M-D
OR
M-A
M-D
M-B
M-E
OR
Choose appropriate screws and washers according to your display.
HEAVY!
You may need assistance with this step.
HEAVY!
You may need assistance with this step.
M -C
3a
Attaching The Display (For VESA 100x100mm)
3b
Attaching The Display (For VESA 75x75mm)
To adjust the display to a desired tilting position, using a 6mm Allen Key (J), slightly loosen or
tighten the adjustment screws based on the weight of the display.
After use, store Allen Keys (I) (J) in the slots behind the cable clip holder.
Connect cables to your display and route through the cable clip and along the arms.
+45°
-45°
J
I
J
6mm
Allen Key
6mm
Allen Key
5mm
Allen Key
4
Adjustments
5
Cable Management
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

QualGear QG-DM-01-022 Operating instructions

Brand
QualGear
Model
QG-DM-01-022
Category
Flat panel desk mounts
Type
Operating instructions

QualGear QG-DM-01-022 is a 3-WAY ARTICULATING SINGLE MONITOR DESK MOUNT that has a weight capacity of 8kg (17.6lbs). It is designed to be installed on the edge of your desk or through a grommet hole. The mount allows you to tilt, swivel, and rotate your monitor to find the perfect viewing angle. It also comes with a cable clip to help you keep your cables organized.

Here are some of the benefits of using the QualGear QG-DM-01-022:

  • Improved ergonomics: The mount can help you to improve your posture and reduce neck and eye strain by allowing you to position your monitor at the optimal height and angle.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents