Maintenance
11
Please check that the projector mount is secure and safe to use at regular intervals. If you have any
questions regarding any of the instructions or warnings, please contact your local distributor (OR)
contact QualGear technical support via email at support@qualgear.com.
5 Year Limited Warranty
Version September 2015
5 Year Limited Warranty
Version September 2015
QG-PM-FT1-WHT
www.qualgear.com
ADJUSTABLES: Vertical Tilt, Horizontal Roll, and
Horizontal Rotation: +/- 5 degrees
Horizontal Slide (Forward/Backward): 358 – 658mm,
from the center of the wall plate
Horizontal Slide (Left/Right): 90mm
CAUTION!
Do not exceed the maximum rated weight
specified. Otherwise, serious injury or
property damage may occur.
PROJECTOR WALL MOUNT
INSTALLATION MANUAL
Installing the Wall Plate Covers and the Decorative Cover
7
Adjusting the Forward/Backward Slide
Locking Screws
W-D
-5°
-5°
5°
5°
[Projector not included][Projector not included]
(33lbs)
RATED
15kg
(33lbs)
RATED
15kg
Wall Plate Cover
Connect the cables to the projector, and install
the wall plate covers and the decorative cover.
Decorative Cover
1 2
Parts Checklist
Please read the entire installation manual before you start installation and assembly.
NOTE
WARNING
Do not begin to install your QualGear product
until you have read and understood all the
instructions and warnings contained in this
installation manual. If you have any questions
regarding the instructions, for US customers
please contact QualGear customer support
via email at support@qualgear.com. For
all international customers, please contact
your local distributor.
This product should only be installed by
someone of good mechanical aptitude, has
experience with basic building construction,
and fully understands these instructions.
This product was designed to be installed
and utilized only as specified in this manual.
Improper installation of this product may cause
damage or serious injury. QualGear is not
liable for the improper use or installation of its
products.
Make sure that the supporting surface
will safely support the combined load of the
equipment and all attached hardware and
components.
Always use an assistant or mechanical
lifting equipment to safely lift and position the
equipment.
Tighten screws firmly, but do not over tighten.
Over tightening can damage the items, greatly
reducing their holding power.
ALL QUALGEAR products are intended for
indoor use only and any outdoor use voids the
limited warranty.
If mounting to wooden studs make sure that
mounting screws are anchored into the center
of the studs. Use of an edge-to-edge stud finder
is highly recommended.
Never exceed the maximum rated weight
specified in this manual.
All bolts and screws must be used at the
designated points in the installation instructions
to prevent property damage
and/or personal
injury.
DO NOT install near air conditioner vents or
where there is excessive dust or smoke.
When drilling holes in the wall, it is very
important to take care of electrical cables,
water, or gas pipes in the wall.
This product was designed to be installed on the following wall construction only:
WALL CONSTRUCTION HARDWARE REQUIRED
Wooden Stud Included
Wooden Beam Included
Solid Concrete Included
dedulcnI kcirB
Other Contact Qualified Professional
Hardware Package
IMPORTANT: Before starting installation, please check that all parts shown in this checklist
are included. If any parts are missing or damaged, contact your local distributor or
[email protected] for replacement parts and do not start assembly and installation
until you receive all the parts.
Mounting Bracket (x1)
Wall Plate (x1)
Extension Arms (x4)
Wall Plate Cover (x1)
M6x55mm Screw (x5)
W-A
ø10mm Concrete Anchor
(x5)
W-B
5mm Allen Key (x1)
W-C
3mm Allen Key (x1)
W-D
M2.5x15mm (x4)
M-A
M3x10mm (x4)
M-B
M4x25mm (x4)
M-G
M3x20mm (x4)
M-F
M4x10mm (x4)
M-C
M5x12mm (x4)
M-D
M6x12mm (x4)
M-E
M5x25mm (x4)
M-H
M6x26mm (x4)
M-I
M6x10mm (x4)
W-E
M5 Nuts (x4)
W-F
Wall Marking Template (x1)
Cable Management
1
3
4
Please refer to the diagram above and the user manual of your projector to determine the
proper placement of the projector wall mount.
Checking the Installation Position
2
Mounting to a Wooden Stud Wall
3a
Feed the projector cable(s) through the mounting bracket.
Mounting Bracket
Using an edge-to-edge stud finder, find the
edges of the stud.
Using the marking template provided,
mark four holes for drilling on the centerline
of each stud.
For concrete or brick wall
mounting, follow Step 3b.
NOTE
3 mm
65mm55mm
1
3 4
2.5")
(2.2")
( 1/8" )
1
2
3
4
5
6
7
8
9
10
11
12
Using a level, mark the centerline of the stud.
2
Stud Finder
F: Distance between the walls/ length of the room
H: Distance from the top of the projector screen to the center of the lens
L: Distance from the wall to the projector
T: Throw distance/ projection distance
V: Distance from the bottom of the floor to the center of the lens
W: Distance from the floor to the bottom of the projector screen
Projection screen
T
T
Projection screen
W
F
V
Short Throw Projectors Regular Projectors
OR
Floor
Wall
WallWall
Using a power drill and 1/8” drill bit, drill pilot
holes of 1/8” (3mm) diameter and at least
2.2” (55mm) depth at the marked locations
in the previous step.
5 6
1
2
3
4
5
6
7
8
9
1
0
1
1
1
2
Mounting to a Concrete or a Brick Wall3b
1
2
10m
0mm
(2 )
( 3/8")
)
60mm
(2. "4
5. Using a 5mm allen key (W-C), mount the wall plate and fasten with the M6x55mm screws (W-A).
Hold the marking template against the wall where you want to install the projector,
mark five holes for drilling.
Using a power drill and a 3/8" masonry drill bit, drill mounting holes of 3/8" (10 mm) diameter
and 2.4" (60 mm) depth at the marked locations in the previous step.
Wall Plate
ConcreteBrick
7
8
Installing the Projector onto the Projector Wall Mount
5
Installing the Mounting Bracket onto the Wall Plate
4
Projector Mounting Plate
Extension Arm
OR
W-F
1 2
W-E
W-C
3
Place concrete anchor (W-B) in each hole. Tap each anchor flush with the
wall using a hammer. Using a 5mm allen key (W-C), mount the wall plate
and fasten with the M6x55mm screw (W-A).
Install the extension arms according to one of the illustrations shown above.
Mounting Bracket
Using 5mm allen key (W-C), attach the mounting bracket to the wall plate with screws (W-E).
Wall Plate
9 10
Adjustment Direction
Adjusting the Horizontal Roll
FRONT
VIEW
OR
M-A/ M-B/ M-C/
M-D/ M-E/ M-F/
M-G/ M-H/ M-I
WITHOUT EXTENSION ARMS
Adjustments
6
After the projector is mounted to the projector mount, make adjustments according to your needs.
According to the type of your projector, choose the appropriate screws, and then attach
the projector mounting plate to the projector, with or without the extension arms.
Adjustment Direction
Side View
Adjustment Buttons
FRONT
VIEW
Adjusting the Vertical Tilt
Adjusting the Leftward/Rightward Slide
Adjusting the Horizontal Rotation
Top View
Adjustment Direction
FRONT
VIEW
IMPORTANT: Use an
assistant to hold the
projector securely while
attaching it to the wall
mount and/or making
adjustments.
Adjustment Direction
/
