AMX AXD-CV10 User manual

instruction manual

To u c h Pa n e l s a n d A c c e s s o r i e s

10.4" Touch Panels

(Firmware version G3)

AMX Limited Warranty and Disclaimer

AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three

(3) years from the date of purchase from AMX Corporation, with the following exceptions:

• Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch

overlay components that are warranted for a period of one (1) year.

• Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one

(1) year.

• AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting

products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the

control of dimmable loads that are properly connected to our lighting products. The dimming performance or

quality cannot be guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers.

• Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.

• AMX Software is warranted for a period of ninety (90) days.

• Batteries and incandescent lamps are not covered under the warranty.

This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer.

All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is

obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box.

The RMA is valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments received

not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products

returned without a valid RMA number.

AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform.

This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not

liable for any claim made by a third party or by an AMX Dealer for a third party.

This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort

claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of

liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX

Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such

damages. This limitation of liability, however, will not apply to claims for personal injury.

Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or

exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of

the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may

also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full

determination of rights.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO

OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION

EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY

IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS

LIMITED WARRANTY.

Table of Contents

i

10.4" Touch Panels

Table of Contents

Product Information .................................................................................................1

Specifications .................................................................................................................... 1

Cleaning the Touch Overlay.............................................................................................. 2

Installation .................................................................................................................3

Mounting the Touch Panel ................................................................................................ 3

Decor style panels with low-profile Backboxes ........................................................................ 3

Installing touch panels and a CB-TP3 Backbox (plasterboard)................................................ 6

Installing rack-mount panels (AXM-CA10/PB) ......................................................................... 8

Wiring the Touch Panel ..................................................................................................... 8

Preparing captive wires............................................................................................................ 8

Wiring guidelines...................................................................................................................... 8

Using the PSN connector for power......................................................................................... 9

Using AXlink for data and power.............................................................................................. 9

Using AXlink for data with a +12 VDC power supply ............................................................. 10

Using the (DB9) RS-232 connector for mouse control or data............................................... 11

Using the VGA IN HD-15 (male) high-density connector ....................................................... 12

Designing Touch Panel Pages ..............................................................................15

Buttons ............................................................................................................................ 15

Activating Edit Mode........................................................................................................ 16

Setting the Device Base .................................................................................................. 18

Setting the Device Used.................................................................................................. 18

Adding a Page................................................................................................................. 18

Setting the page color ............................................................................................................ 18

Adding a Button............................................................................................................... 18

Resizing a button ................................................................................................................... 19

Defining On-Screen and External Button Properties....................................................... 19

Setting the channel code........................................................................................................ 19

Setting the variable text code................................................................................................. 20

Setting the page flip ............................................................................................................... 20

Setting the button colors for channel-off conditions ............................................................... 21

Adding text, icons, and bitmaps to a button ........................................................................... 21

Using TPDesign3 to Download Bitmaps, Icons, and Fonts............................................. 21

Creating a Bargraph and Joystick ................................................................................... 22

Adding a bargraph or joystick button...................................................................................... 22

Setting Bargraph and Joystick Properties ....................................................................... 22

Setting the level code............................................................................................................. 22

ii

10.4" Touch Panels

Table of Contents

Programming ..........................................................................................................25

Serial Commands............................................................................................................ 25

System Send_Commands .............................................................................................. 28

Video Send_Commands ................................................................................................. 33

VGA Send_Commands................................................................................................... 35

Programming Numbers ................................................................................................... 37

Shorthand Send_Commands.......................................................................................... 38

Color Send_Commands.................................................................................................. 43

Variable Text Send_Commands ..................................................................................... 45

Shorthand Variable Text Commands .............................................................................. 47

Button String Commands................................................................................................ 50

Upgrading the Firmware ........................................................................................53

Upgrading the Firmware Using NetLinx Studio ............................................................... 53

Upgrading Firmware through a COM port.............................................................................. 53

Upgrading the Firmware through an IP Address.................................................................... 55

Upgrading the Firmware Using SoftROM........................................................................ 57

Configuration.......................................................................................................................... 58

Downloading the Firmware .................................................................................................... 58

Changing the LCD Viewing Angle ........................................................................59

Changing the Viewing Angle to 6 o’clock (podium mount).............................................. 59

Replacing the Batteries .........................................................................................61

Product Information

1

10.4"Touch Panels

Product Information

The AMX™ CA10, CV10 and CG10 touch panels contain a 10.4", 256-color active matrix liquid

crystal display (LCD). The self-contained enclosures use a microprocessor to control a wide range

of multimedia equipment. The TPDesign3 touch panel design program makes it possible to create

custom pages with buttons, icons, sliders, bargraphs, time displays, logos, and drawings.

All Decor-style references in this manual relate to wall mounted panels.

The table below lists the panel types and product names discussed in this manual.

Specifications

The table below lists the CA10, CV10, and CG10 specifications.

Touch Panel Types and Product Names

Product Names

Panel Types Standard

(Color Active)

Video

(NTSC/PAL)

Graphic

(VGA/SVGA/XGA/DOS)

Free standing:

TiltScreen AXT-CA10 AXT-CV10 AXT-CG10

Wall Mount:

Decor style AXD-CA10 AXD-CV10 AXD-CG10

Rack Mount:

Rack-mount AXM-CA10 AXM-CV10 AXM-CG10

Pushbutton AXD-CA10/PB

AXM-CA10/PB

AXD-CV10/PB

AXM-CV10/PB

AXD-CG10/PB

AXM-CG10/PB

Specifications

Dimensions (HWD):

AXD - Decor Wall Mount • 8.88" x 12.88" x 2.19" (22.56 cm x 32.72 cm x 5.56 cm)

AXM- Rack-Mount • 8.72" x 19.00" x 1.78" (22.15 cm x 48.26 cm x 4.52 cm)

AXT- TiltScreen • Base (WD): 11.46" x 9.46" (29.11 cm x 24.03 cm)

• Height lowered: 4.14" (10.52 cm)

• Height raised: 9.84" (25.0 cm)

Display Area (HV) • 211.1 mm x 158.4 mm

Display Colors • 256K colors

Pixel Resolution • 640 x 480 pixels

Dot Pixel Pitch • 0.33 mm

Contrast Ratio • 300: 1

Brightness • 350 cd/m

2

Viewing Angles • Horizontal: + 50° (left/right sides)

• Vertical: +

40° (up/down)

Wider Viewing Angle • Without image reversal: Up side (12 o’clock normal scan) and

Down side (6 o’clock reverse scan)

• With contrast ratio: Up side (12 o’clock reverse scan) and

Down side (6 o’clock normal scan)

Product Information

2

10.4" Touch Panels

Cleaning the Touch Overlay

You should clean the touch screen overlay after each day’s use. Always use clean cotton cloths, and

a spray bottle of cleaning solution consisting of 50% isopropyl alcohol and 50% water.

Specifications (Cont.)

Power 12 VDC @ 1 A

Memory Standard: 5 MB (4 MB flash)

Weight:

Decor • 6.0 lbs. (2.7 kg)

Rack-mount • 6.0 lbs. (2.7 kg)

TiltScreen • 4.6 lbs. (2.1 kg)

VGA Input Resolutions:

640 x 400 (DOS)

(The frame frequency [FF] calculations are based on monitor type and VGA

settings.)

FF: 70 Hz

640 x 480 (VGA) FF: 60 and 72 Hz

800 x 600 (SVGA) FF: 52, 60, and 72 Hz

1024 x 768 (XGA) FF: 60 and 70 Hz

Rear Panel Connectors:

AXlink • 4-pin AXlink data/power bus jack

RS-232 • DB9 male connector for PC data transmission or Microsoft

®

mouse control

Video • RCA female connector (Color Video/Graphic AXT models only)

• BNC female connector (Color Video/Graphic AXD and AXM models)

Graphics • 15-pin HD-15 (high-density) male connector (Color Graphic model only)

PWR • 2-pin 12 VDC power supply jack

Enclosure:

Decor Metal with black matte finish, screwed security overlay, CB-TP3 Backbox

TiltScreen Black plastic with matte finish

Rack-mount Metal with black matte finish, engraved overlay, low-profile Backbox

Character Support • Unicode character support

Included Accessories: • 4-pin AXlink data/power connector (41-0049)

• 2-pin PWR connector (41-0021)

Optional Accessories:

Decor • Up to 24 external pushbuttons

• Backbox (CB-TP3) (FG025-10)

Rack-mount • Up to 24 external pushbuttons

TiltScreen • Install Kit (SA2010-01)

4-pin AXlink data/power connector (41-0049)

Tie wrap (45-0009)

Cable tie holder (45-0009-01)

CG10 panels are capable of receiving a VGA signal. These VGA signals can be

displayed on a touch panel as a background image and NOT within a video button. A

Video signal can only be displayed within a Video WIndow Button. Refer to the G3

Firmware manual for more detailed information.

Installation

3

10.4" Touch Panels

Installation

Mounting the Touch Panel

The following paragraphs describe mounting the Decor and rack-mount touch panels. TiltScreen

touch panels can be placed on any flat surface.

Decor style panels with low-profile Backboxes

1. Cut out the surface using the dimensions shown in FIG. 1.

2. Carefully insert a flat-blade screwdriver into the release slot on the touch panel’s faceplate and

remove the engraved overlay.

3. Place the touch panel into the cutout and mark the screw insert positions, as shown in FIG. 1.

4. Remove the touch panel and drill four #6-32 insert holes. Then, place a threaded insert into

each hole.

FIG. 1 AXD-CA10 and low profile Backbox cutout dimensions

Installation

4

10.4" Touch Panels

5. Disconnect the AXlink connector from the Central Controller, RS-232 connector, and the

optional graphic/video wiring from the external RS-232 device connected to the source

equipment.

6. Thread the incoming AXlink, RS-232, and optional graphic/video wiring through the low-

profile Backbox.

7. Fasten the low-profile Backbox using the #6-32 machine screws supplied with the enclosure.

8. Attach the data and power wiring to the touch panel.

9. Test the connection by reconnecting the AXlink connector to the Central Controller, RS-232

connector, and optional graphic/video wiring to the source equipment. Before continuing,

disconnect all connections until panel installation is complete.

10. Fasten the touch panel and low-profile Backbox using the #6-32 machine screws supplied with

the enclosure panel.

11. Place the faceplate onto the bezel. You can also secure the faceplate to the bezel using the four

Phillips flathead security screws. Once attached to the faceplate, the security screws cannot be

replaced without removing the overlay.

12. Remove the backing from the adhesive tape strips located on the front of the panel; press the

engraved overlay onto the faceplate.

13. Reconnect the AXlink wiring to the Central Controller, RS-232 wiring to the mouse (if used),

and optional graphic/video wiring to the source equipment. The touch panel beeps on power-

up. Refer to the Wiring the Touch Panel section on page 8 for complete information.

Installing touch panels and a CB-TP3 Backbox (solid surface)

FIG. 2 shows an AXD-CA10/PB and CB-TP3 UniMount Backbox for solid surfaces.

1. Cut out the surface using the dimensions shown in FIG. 3.

FIG. 2 AXD-CA10/PB and CB-TP3 for solid surfaces

CB-TP3 Unimount

Backbox enclosure

Knockout

Solid surface mounting flanges

Stud mounting

holes

Engraved overlay

AXD-CA10/PB

faceplate

Installation

5

10.4" Touch Panels

2. Carefully insert a flat-blade screwdriver into the release slot on the touch panel’s bezel and

remove the engraved overlay.

3. Lay the touch panel facedown on a soft cloth and remove the screws from the low-profile

Backbox; remove the Backbox and discard.

4. Place the CB-TP3 into the cutout and mark the threaded insert positions, as shown in FIG. 3.

5. Remove the CB-TP3 and drill eight holes (A and B) for the panel (FIG. 3). Then, place #6-32

threaded inserts (or screw anchors) into the four holes marked ‘B’ (FIG. 3).

6. Disconnect the AXlink connector from the Central Controller, RS-232 connector, and the

optional graphic/video wiring from the source equipment.

7. Remove one or more knockouts to accommodate the wiring.

8. Thread the incoming AXlink, RS-232, and optional graphic/video wiring through the CB-TP3

knockouts. Refer to the Wiring the Touch Panel section on page 8 for pinout descriptions.

FIG. 3 Decor style (AXD) and CB-TP3 cutout dimensions (solid surfaces)

The CB-TP3 can also be mounted to wood or metal studs using the pre-drilled stud

mounting holes.

Installation

6

10.4" Touch Panels

9. Fasten the CB-TP3 to the solid surface using the supplied mounting screws. The touch panel

must be installed with the release slot at the bottom.

10. Connect the AXlink, RS-232, and optional graphic/video wiring to the touch panel.

11. Test the connection by reconnecting the AXlink connector to the Central Controller and the

optional video wiring to the video source. The panel beeps on power-up. Before continuing,

disconnect all connections until panel installation is complete.

12. Fasten the touch panel to the CB-TP3 using the #6-32 screws supplied with the panel.

13. Place the Decor-style faceplate onto the bezel. You can also secure the faceplate to the bezel

using the four Phillips flathead security screws.

14. Remove the backing from the adhesive tape strips; press the engraved overlay onto the

faceplate. Once attached to the faceplate, the security screws cannot be replaced without

removing the overlay.

15. Reconnect the AXlink wiring to the Central Controller, RS-232 wiring to the mouse (if used),

and optional graphic/video wiring to the source equipment. The touch panel will beep on

power-up.

Installing touch panels and a CB-TP3 Backbox (plasterboard)

FIG. 4 shows the AXD-CA10/PB and CB-TP3 Backbox for plasterboard.

1. Cut out the surface using the dimensions shown in FIG. 5.

2. Carefully insert a flat-blade screwdriver into the release slot on the touch panel's faceplate and

remove the engraved overlay.

3. Lay the touch panel facedown onto a soft cloth and remove the screws from the low-profile

Backbox. Remove the Backbox and discard.

4. Place the CB-TP3 into the cutout and mark the threaded insert positions (FIG. 5).

FIG. 4 AXD-CA10/PB and CB-TP3 Backbox (plasterboard)

CB-TP3 Unimount

Backbox enclosure

Knockout

Plasterboard surface mounting flanges

Engraved overlay

AXD-CA10/PB

faceplate

Expansion clips

Installation

7

10.4" Touch Panels

5. Remove the CB-TP3 and drill four #6-32 insert holes. Then, place a threaded insert (or screw

anchor) into each hole.

6. Disconnect the AXlink connector from the Central Controller, RS-232 connector, and the

optional graphic/video wiring from the source equipment.

7. Remove one or more knockouts to accommodate the wiring as required.

8. Thread the incoming AXlink, RS-232 connector, and the optional graphic/video wiring

through the CB-TP3 knockouts. Refer to Wiring the Touch Panel section on page 8 for more

information.

9. Fasten the CB-TP3 to the plasterboard using the expansion screws supplied with the enclosure.

10. Connect the AXlink, RS-232, and the optional graphic/video wiring to the touch panel.

11. Test the connection by reconnecting the AXlink connector to the Central Controller and the

optional video wiring to the video equipment. The panel beeps on power-up. Before

continuing, disconnect all connections until panel installation is complete.

12. Fasten the touch panel to the CB-TP3 with the #6-32 screws supplied with the panel.

13. Place the Decor-style faceplate onto the bezel. You can also secure the faceplate to the bezel

using the four Phillips flat-head security screws.

FIG. 5 Decor style (AXD) and CB-TP3 cutout dimensions for plasterboard

Installation

8

10.4" Touch Panels

14. Remove the backing from the adhesive tape strips; press the engraved overlay onto the

faceplate. Once attached to the faceplate, the security screws cannot be replaced without

removing the overlay.

15. Reconnect the AXlink wiring to the Central Controller, RS-232 wiring to the mouse (if used),

and optional graphic/video wiring to the source equipment. The touch panel beeps on power-

up.

Installing rack-mount panels (AXM-CA10/PB)

1. Thread the incoming AXlink, RS-232, and optional graphic/video wiring through the opening

in the equipment rack.

2. Disconnect the AXlink connector from the Central Controller, the RS-232, and optional

graphic/video wiring from the source equipment.

3. Insert the touch panel into the equipment rack. Line up the top-left and bottom-right screw

holes and start tightening the #6-32 screws. Then, tighten the bottom-left and top-right screws.

4. Connect the AXlink wiring to the Central Controller, RS-232, and optional graphic/video

wiring to the touch panel. Refer to the Wiring Guidelines table for pinout descriptions. The

touch panel beeps on power-up.

Wiring the Touch Panel

The touch panels use a 4-pin AXlink connector for power and data. If the distance between the

panel and Central Controller exceeds power consumption limits, you must connect an optional

12 VDC power supply to the 2-pin PWR connector.

Preparing captive wires

You need a wire stripper, soldering iron, and flat-blade screwdriver to prepare and connect the

captive wires.

1. Strip 0.25 inch of wire insulation off all wires.

2. Insert each wire into the appropriate opening on the connector according to the wiring

diagrams and connector types described in this subsection.

3. Turn the flat-blade screws clockwise to secure the wire in the connector. Do not over-torque

the screws; doing so can bend the seating pin and damage the connector.

Wiring guidelines

The touch panels require 12 VDC power to operate properly. The touch panel can use either a

PSN2.8 (if the power is being supplied only to the touch panel) or a PSN6.5 power supply (if the

power is being routed through the touch panel to power another device). The Central Controller

supplies power via the AXlink cable or external 12 VDC power supply. The maximum wiring

distance between the Central Controller and touch panel is determined by power consumption,

supplied voltage, and the wire gauge used for the cable. The table below lists wire sizes and the

maximum lengths allowable between the touch panel and Central Controller.

Do not connect power to the touch panel until the wiring is complete. If you are using

a 12 VDC power supply, apply power to the touch panel only after installation is

complete.

Installation

9

10.4" Touch Panels

The maximum wiring lengths for using AXlink power are based on a minimum of 13.5 VDC

available at the Central Controller's power supply. Refer to the Specifications section on page 1 for

more information on power requirements.

If you install the touch panel farther away from the control system than recommended in the Wiring

Guidelines table, connect an external 12 VDC power supply to the 2-pin PWR connector on the

touch panel.

Using the PSN connector for power

To use the 2-pin mini-Phoenix power supply jack for power transfer from the PSN power supply,

the incoming PWR and GND cable from the PSN must be connected to the corresponding location

on the 2-pin AXlink connector (FIG. 6).

1. Insert the PWR and GND wires into the terminal end of the PSN 2-pin AXlink cable.

2. Tighten the clamp to secure the two wires.

3. Verify the connection of the other end to the 2-pin 3.5 mm mini-Phoenix on the PSN.

Using AXlink for data and power

Connect the Central Controller's AXlink connector to the AXlink connector on the touch panel for

data and 12 VDC power as shown in FIG. 7.

Wiring Guidelines

Maximum Wiring Length

Wire Size Color Active Color Graphic Color Video

18 AWG 143.14 feet (43.63 m) 93.90 feet (28.62 m) 130.05 feet (39.64 m)

20 AWG 90.56 feet (27.60 m) 59.41 feet (18.11 m) 78.17 feet (23.83 m)

22 AWG 56.46 feet (17.21 m) 37.04 feet (11.29 m) 48.73 feet (14.85 m)

24 AWG 35.59 feet (10.85 m) 23.35 feet (7.12 m) 30.72 feet (9.36 m)

FIG. 6 Power connector wiring diagram

PWR +

GND -

To the panel

To the PSN Power Supply

(terminal end)

(either a PSN2.8 or PSN6.5)

Installation

10

10.4" Touch Panels

Using AXlink for data with a +12 VDC power supply

To use the AXlink 4-pin connector for data communication with the Central Controller and power

transfer from a power supply, the incoming PWR and GND cable from the power supply must be

connected to the AXlink cable connector going to the touch panel. FIG. 8 shows the external power

supply diagram.

1. Unscrew the PWR and GND wires on the terminal end of the power supply’s 2-pin cable.

2. Pair the GND wires from the power supply and the Central Controller AXlink connectors

together; insert them into the clamp position for GND on the touch panel AXlink connector.

3. Tighten the clamp and secure the two GND wires.

FIG. 7 AXlink wiring diagram

PWR +

AXP/TX

AXM/RX

GND -

To the touch panel

To the external Central Controller

AXlinx/PWR connector

PWR +

AXP/TX

AXM/RX

GND -

Top vi ew

Top view

If you are using power from AXlink, disconnect the wiring from the Central Controller

before wiring the touch panel.

FIG. 8 AXlink and external 12 VDC power supply wiring diagram

PWR (+)

GND (-)

Local +12 VDC

(coming from

PWR +

AXP/TX

AXM/RX

GND -

To the touch panel

To the external Central Controller

AXlinx/PWR connector

PWR +

AXP/TX

AXM/RX

GND -

power supply

the PSN

power supply)

To p vi ew

Top view

Installation

11

10.4" Touch Panels

4. Place the PWR wire from the power supply into the open clamp position for PWR on the touch

panel AXlink connector.

Using the (DB9) RS-232 connector for mouse control or data

The dual-function (DB9) RS-232 connector supports most standard serial mouse control devices

and RS-232 communication protocols for PC data transmission.

The following table lists (DB9) RS-232 connector pinouts and FIG. 9 shows the (DB9) RS-232

connector and power supply wiring diagram.

Use connector pins 2, 3, and 5 for data and ground. For some applications, you may need to strap

pins 7 (request to send) and 8 (clear to send) together, depending on the PC.

Never connect both power wires from the power supply and Central Controller to the

PWR terminal on the touch panel AXlink connector. Only the power supply’s PWR

wire should be connected to the touch panel AXlink connector. If both sources are

used to provide power to the touch panel, an electrical hazard is created and the

threat of both equipment damage and injury is likely.

(DB9) RS-232 Connector Pinouts

Pin Signal Function

1 N/A Not used

2 RXD Receive data

3 TXD Transmit data

4 DTR Data terminal ready (not used)

5 GND Signal ground

6 DSR Data set ready (not used)

7 RTS Request to send (not used)

8 CTS Clear to send (not used)

9 N/A Not used

FIG. 9 DB9 RS-232 connector and power supply wiring diagram

9

8

7

6

5

4

3

2

1

9

8

7

6

Female

Male

Power connector

Mouse or PC, DB9 connector

Female

Male

Touch panel

DB9 connector

Optional 7 to 8-pin

connector

2 (RXD)

3 (TXD)

5 (GND)

2 (RXD)

3 (TXD)

5 (GND)

+ (PWR)

- (GND)

12 VDC power supply

Installation

12

10.4" Touch Panels

Using the VGA IN HD-15 (male) high-density connector

Connect the VGA source equipment’s HD-15 (female) connector to the VGA IN HD-15 (male)

high-density connector on the rear panel of the touch panel. The table below lists the VGA IN

HD-15 connector pinouts.

VGA IN HD-15 Connector Pinouts

Pin Signal Function

1 Red Red signals

2 Green Green signals

3 Blue Blue signals

4 N/A Not used

5 GND Signal Ground

6 RAGND Red analog ground

7 GAGND Green analog ground

8 BAGND Blue analog ground

9 N/A Not used

10 SAGND Synchronization analog ground

11 N/A Not used

12 N/A Not used

13 HSYNC Horizontal synchronization signal

14 VSYNC Vertical synchronization signal

15 N/A Not used

VGA HD-15 (male)

connector

10

6

5

1

15

11

CG10 panels are capable of receiving a VGA signal. These VGA signals can be

displayed on a touch panel as a background image and NOT within a video button.

An RGB signal can only be displayed within a Video WIndow Button.

Installation

13

10.4" Touch Panels

Installation

14

10.4" Touch Panels

Designing Touch Panel Pages

15

10.4" Touch Panels

Designing Touch Panel Pages

There are two ways to approach creating touch panel pages:

! TPDesign3 - Refer to the TPDesign3 Touch Panel Program (Version 3. 16 or higher)

Instruction Manual for more information.

! On-board editor

This section describes the basics of using the on-board editor to create pages and buttons. For more

information, refer to the G3 Firmware Design and Reference instruction manual.

Buttons

Standard button types include rectangles and other geometric shapes you can create with the touch

panel editor. Buttons are set with attributes, meaning there is a response from the Central Controller

when you touch the button.

General buttons are part of the default touch panel program and cannot be changed. General buttons

create or revise pages and specify panel communication parameters. Button examples include

selection buttons, information buttons, adjustment buttons, and operation bars. The general button

categories are described in the table below.

General Button Categories

Selection buttons Selection buttons appear on touch panel pages and set communica-

tion parameters.

Information buttons Information buttons contain serial numbers and firmware version

information. The properties of these buttons cannot be changed.

These buttons have a dark fill and light text.

Adjustment buttons You can use the UP and DN buttons to set adjustment buttons. The

adjustment button example sets the baud rate for the connection

from the touch panel to the computer.

Keypad buttons The keypad button opens a keypad so you can enter a password or

value assignment. All keypad buttons are interactive except for the

entry display.

Decision buttons Decision buttons appear when an operation has two options and

requires verification before an action is performed.

Designing Touch Panel Pages

16

10.4" Touch Panels

Activating Edit Mode

Before designing touch panel pages and buttons, you must activate Edit mode. Once activated, use

the

EDIT button to enter Edit mode. This mode has options to add and configure touch panels and

buttons. When powering up the touch panel, the first page is the Main page (see FIG. 10). Note that

the Edit button is not available initially. If you have a pre-programmed panel, you may not see the

Main Page.

To activate edit mode:

1. Press

SETUP in the Main page to open the Setup page (FIG. 11).

2. Press

PROTECTED SETUP to open the keypad.

3. Enter 1988 (default password) in the keypad and press

ENTER to open Protected Setup page. If

you press

ENTER after typing an incorrect password, you are immediately returned to the

previous page.

General Button Categories (Cont.)

Status buttons Status buttons always have a dark fill with light letters and have no

functionality except to display information.

Operation bars Operation bars appear in the place of the Editor bar, after selecting a

button or page edit operation. The operation bar indicates which edit

function is currently active. When an edit operation is selected, it

remains active until you press EXIT.

Touch to Continue buttons "Touch to Continue" buttons appear when an operation requires user

acknowledgement.

Joystick buttons Joysticks are vertical and horizontal direction controllers for use with

pan and tilt camera controllers.

Bargraph buttons Bargraph buttons display a dynamic bargraph (vertical or horizontal).

An example is the battery level indicator button.

FIG. 10 Main Page

Page is loading ...

AMX AXD-CV10 User manual

This manual is also suitable for

AMX AXD-CV10 User manual

Related papers

Other documents