© Copyright 2010 • Ariens Company • Brillion, WI 54110 01327000A 6/10 Page 1 of 4
Instruction Sheet
Kit Number: 71106600
WIDE AREA WALK BAGGER KIT
For use on models:
911403, 911404, 911407, 911408, 911410, 911411
Package Contents
Check the contents of your kit for the parts listed below
(Figure 1):
* These items are used only on models: 911403, 911404,
911407, 911408.
WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in personal injury
and/or damage to unit.
Read, understand, and follow all safety
practices in Owner/Operator Manual before
beginning.
Item Part No. Qty. Description
1 01287751 1 Right Side Reinforcing Bracket*
2 01287851 1 Left Side Reinforcing Bracket*
3 05958000 4 3/8"-16 x 1-1/4" Hex Bolt*
4 06442400 4 Flat Washer*
5 06545500 4 3/8"-16 Nyloc Flange Nut*
6 01326951 1 Bagger Baffle Bracket
7 00696451 2 Push Nut
8 51517700 1 34" Stamped Deck Boot
Assembly
9 03391251 1 Bagger Bracket
03391351 1 Bagger Brace
06215700 2 3/8"-18 x 3/4" Roundhead
Squareneck Bolt
06543100 2 3/8"-18 Locking Top Flange Nut
00914700 24.5" Bulk Trim
10 06537100 2 Nyloc Wing Nut
11 01241851 1 Bagger Frame
12 01180500 1 Grass Bag
13 06400006 4 Washer, Flat Steel .406 x 1.50 x
.245
CAUTION: Thoroughly inspect and clear work
area of objects which might be picked up and
thrown. Remove all stones, sticks, wires and
other foreign objects.
CAUTION: DO NOT operate mower on gravel or
on loose material such as sand. Stop mower/
blade when crossing gravel drives, walks, or
roads. Objects may be picked up and thrown,
causing damage or injury.
CAUTION: NEVER direct discharge of material
toward bystanders nor allow anyone near
equipment while unit is in operation. The operator
is responsible for the safety of bystanders.
ACCIDENTAL ENGINE START UP can cause death
or serious injury. ALWAYS stop engine, remove key,
wait for moving parts to stop and remove wire from
spark plug before adjusting or servicing.
Check grass bag for wear and/or deterioration
before each use. Replace only with Ariens original
equipment replacement parts for safety.
Figure 1
1
2
8
3
9
4
10
5
11
12
6
7
13
01327000 6/10 Page 2 of 4
INSTALLATION
To install bagger:
1. Lift discharge deflector fully and tie out of the way.
2. Remove two 3/8" x 3/4" bolts and 3/8" nuts from
mower deck discharge chute area and discard. See
Figure 2.
3. Remove the belt cover nut (or wing knob) by the
discharge chute and retain.
NOTE: Steps 4 – 7 apply only to models 911410 and
911411.
4. Remove the remaining two nuts securing the belt
cover and retain. Remove the belt cover. See
Figure 3.
5. Remove the remaining 3/8" x 3/4" bolt and 3/8" nut
and remove the baffle. See Figure 4.
6. Insert the hardware removed in step 5 back in the
mounting hole in mower deck and tighten securely.
NOTE: Save the baffle for future use without the bagger.
7. Install the belt cover and retain securely with the
two nuts removed in step 4.
NOTE: Steps 8 – 16 apply only to models 911403,
911404, 911407 and 911408. See Figure 5.
8. Lift the front of the mower high enough to remove
the front caster wheels. Securely support unit with
blocks.
9. Remove caster forks from the caster arms. Retain
all hardware.
10. Remove two front bolts retaining the caster arm
weldments to the deck bracket on both sides.
Retain hardware.
11. Using the hardware just removed, temporarily
attach the Right Side Reinforcing Bracket (item 1)
and Left Side Reinforcing Bracket (item 2).
NOTE: Make sure that the brackets are positioned cor-
rectly so they follow the contours of the deck before
marking drill locations.
12. Use the holes in the brackets to locate the drilling
locations in the mower deck. Center punch the drill
locations and remove the brackets.
WARNING: DO NOT operate mower unless
bagger or side discharge deflector is installed.
Objects may be picked up and thrown causing
damage or personal injury.
Figure 2
Remove hardware
and discard.
Remove nut or wing
knob and retain.
Discharge
Deflector
Models 910410
& 910411 Only
Figure 3
Belt Cover
Remove
nuts.
Figure 4
Models 910410
& 910411 Only
Remove
hardware.
01327000 6/10 Page 3 of 4
13. Drill four 3/8" mounting holes in mower deck.
14. Install the reinforcing brackets using the original
hardware and the 3/8"-16 x 1-1/4" Hex Bolts
(item 3), Flat Washers (item 4) and Nyloc Flange
Nuts (item 5). See Figure 5.
NOTE: After attaching the reinforcement brackets to the
caster arms, check if there is a gap between the deck
shell and the reinforcement brackets. If there is a gap,
install the (4) steel flat washers (item 13).
NOTE: It is not necessary to remove the reinforcing
brackets when the bagger is not attached.
15. Install the caster forks in the caster arms.
16. Return unit to operating position.
17. Attach the Bagger Baffle Bracket (item 6) to the
deck by inserting the studs up through the deck.
Install push nuts (item 7) to hold baffle in position.
Make sure that baffle on bracket is positioned to the
rear. See Figure 6.
18. Install the 34" Stamped Deck Boot Assembly
(item 8) on the Bagger Bracket Assembly (item 9).
Align the holes in the boot mounting plate with the
holes in the mounting bracket. See Figure 7.
19. Install the 34" Stamped Deck Boot Assembly and
Bagger Bracket Assembly on the deck. Secure with
two Nylon Wing Nuts (item 10) and nut (or wing
knob) removed in step 3. See Figure 8.
NOTE: Ensure that 34" Stamped Deck Boot Assembly
covers the discharge opening before tightening hard-
ware.
20. Tighten wing nuts and belt cover nut (or wing knob)
fully, ensuring the threads engage the nylon locking
material.
21. Release discharge deflector from tied-back
position.
22. Assemble Grass Bag (item 12) onto Bagger Frame
(item 11) by sliding bag over frame and hooking the
plastic bag edges to the frame.
23. Hook the Grass Bag assembly (items 11 and 12)
onto the Bagger Bracket (item 9). See Figure 9.
Figure 5
Drill 3/8" holes.
Existing
hardware
4
5
2
3
3
1
3
Caster Arm
Weldments
13
13
13
Figure 6
7
6
Figure 7
8
9
Align holes in
boot mounting
plate and
bagger bracket.
Figure 8
Nut or
Wing Knob
10
01327000 6/10 Page 4 of 4
24. Be sure there are no openings between bag and
mounting surface after installing bag. If necessary
clear bag mounting surfaces of debris.
CLEANING AND STORAGE
Remove grass bag and clean out all debris prior to
storage. Grass bag may be stored in position on mower.
Keep grass bag dry during storage.
Figure 9
11
12
9
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Gravely 892031 User manual
-
Gravely ZT Bagger Owner's And Operator's Manual
-
Toro 100 Series Z Master User manual
-
-
-
-
-
Gravely 911411 WAW 34 User manual
-
Toro 60in E-Z Vac DFS Collection System, Z Master G3 Mower User manual
-
