2. CAME
  3. LUXO

CAME LUXO Installation guide

  • Hello! I've analyzed the provided installation manual for the CAME video entry kit, including models 001DC02LUXO, 001DC008AC, 001DC009AC, 001DC011AC, and 001DC01ENIGMA. This document provides comprehensive installation and programming instructions, covering various aspects such as power connections, relay configurations, and camera setup. I am here to assist you with any questions you may have regarding the installation and configuration of this system.
  • What is the purpose of the relay module (001DC009AC)?
    What is the function of the AC/DC converter (001DC011AC)?
    What is the recommended installation position for the power supplier 001DC008AC?
    How can I program the melodies associated with a call?
    How to adjust the camera’s “visual field”?
    How can I program the door lock release code?
G
001DC008AC001DC02LUXO
001DC01ENIGMA
NC
TIMER
C2 NO
PROG
NC C1 NO
B
ON 1 2 3 4 5 86 7
001DC009AC
10
11
7
2
–
–
+
001DC011AC
001DC009AC001DC011AC
INSTALLATION MANUAL
001CK0018FR
001CK0019FR
EN
English
FA00964-EN
VIDEO ENTRY KIT
2
1
a
212
161
29
60
83,5
83,5
B
A
Page 2 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
General Notes
• Read the instructions carefully before beginning the installation and carry
out the actions as specied by the manufacturer.
• The installation, programming, commissioning and maintenance of the
product must only be carried out by qualied technicians, properly trained
in compliance with the regulations in force, including health and safety
measures and the disposal of packaging.
• The installer must ensure that the information for the user, where there is
any, is provided and delivered.
• Before carrying out any cleaning or maintenance operation, disconnect the
devices from the power supply.
• The equipment must only be used for the purpose for which it was
expressly designed.
• The manufacturer declines all liability for any damage as a result of impro-
per, incorrect or unreasonable use.
This product complies with the relevant directives in force.
Decommissioning and disposal. Dispose of the packaging and the device
at the end of its life cycle responsibly, in compliance with the laws in force
in the country where the product is used. The recyclable components are
marked with a symbol and the material's ID marker.
The data and information shown in this manual are to be considered as
subject to change at any time and without the need for any advance warning.
Measurements, unless otherwise indicated, are in millimetres.
001DC02LUXO
Wall-mounted installation
Unfasten the equipment from the metal support by letting it run smoothly
along it after you have pressed the plastic catch A.
Fix the metal support to the round Ø 60 mm back-box Ba or the rectan-
gular 503 back-box BB using the screws provided and paying
attention to the (TOP) direction indication. The box must be installed at
an appropriate height for the user. Avoid tightening the screws too much.
Once the connections are made, hook the video terminal onto the metal
support CD.To unhook the unit from the metal support press the plastic
catch and lift the terminal E.
For recessed installation refer to the recessing kit manual
D
F
G
CL.RES
SW4
M1
SW4 SW4 SW4
SW5 SW5
001DC006AC
1 2 3
①
1
E
Page 3 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Features
Terminal board Fa
+Local power supply
–
BBUS line input
+Doorbell
–
AL Alarm Input
Selection of last receiver on the line G (SW4)
Setting melodies
☞ All the programming stages described below must be carried out
in sequence:
1- Going into Programming.
Press button 5 times in 5 secs.
A short beep conrms that you have entered programming mode.
2- Programming the melody associated with a call from the entry panel.
To listen to the melodies in sequence, press key .
To select the melody and exit programming, press key .
To select the melody and continue with programming, press key .
3- Programming the melody associated with a call from the front door.
To listen to the melodies in sequence, press key .
To select the melody and exit programming, press key .
To select the melody and continue with programming, press key .
4- Programming the number of rings for the call.
Press key as many times as you want it to ring (from 1 to 6 rings). Three
seconds after the last press of the key the call selected for the chosen number
of rings will be played back.
To exit programming, press key .
☞ See the entry panel documentation for call programming.
Technical features
Type
001DC02LUXO
Local power supply (VDC)
16÷18
Consumption (max mA)
300
Consumption in stand-by mode (mA)
<10
Single LED consumption (mA)
(panic, disable ring tone)
1
Storage temperature (°C)
-25 ÷ +70
Operating temperature (°C)
0 ÷ +35
IP Rating
20
Video standard
PAL/NTSC
LCD TFT colour display (inches)
7
A
43,5
45
7,5 57
140
106
A
B
64,5
140
145
43,5
45
7,5 57
140
106
A
B
64,5
140
145
A
G
a 
Page 4 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
001DC008AC
Installation
The power supplier must ALWAYS be installed horizontally. The device can be
installed on a DIN rail (EN 50022) in an appropriate electric panel.
NOTE. Proper ventilation is required if the power supplier is installed in a
metal container.
Technical features
Type
001DC008AC
Power supply [V AC]
230
Max current demand [A AC] 0,25
Max energy dissipation [W] 10
Nominal power supply [V DC]
17,5
Nominal current [A] 1,7
Storage temperature [°C] -25 ÷ +70
Operating temperature [°C]
0 ÷ +35
IP Rating [IP] 30
Features A
Terminal board a
~Mains
~
Terminal board
1
2Power supply 17,5 VDC (*)
1
2Power supply 17,5 VDC (*)
(*) The appliance is electronically protected against overloads and short
circuits.
A
48,5 mm
21 mm
60 mm
85,5 mm
69,5 mm
2
1
1234567 8
NC
TIMER
C2 NO
PROG
NC C1 NO
B
VLS/2
Made in Italy
ON
1 2 3 4 5 86 7
1234567 8
NC
TIMER
C2 NO
PROG
NC C1 NO
B
VLS/2
Made in Italy
ON
1 2 3 4 5 86 7
001DC009AC
a
B
Page 5 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
001DC009AC
Device description
The device can be used in series X1 and X2 systems for per the activation
of auxiliary services.
It is equipped with two relays which can be associated with door lock release
or auxiliary commands of the receivers (Aux1 button, Aux2 button, etc.) or
with numerical codes entered on the entry panel keypad (updated to the
fw 1.06.001 version and later).
NOTE. The commands are always active, irrespective of whether the system
is on or o.
The device is factory set to operate in the following way:
- the door lock release button of the receiver activates relay 1 for a
time period of between 1 and 16 secs, which can be adjusted using the
TIMER potentiometer;
- the Aux 2 button of the receiver activates relay 2 for 1 second;
- for entry panels with a keypad, code ‘12345’ activates relay 1 for a variable
amount of time between 1 and 16 seconds, which can be adjusted using
the TIMER potentiometer;
- for entry panels with a keypad, code ‘09876’ activates relay 2 for 1 second.
y By default all dip-switches are in the OFF position.
Installation A
The device can be installed on a DIN rail (EN 50022). It can also be installed
on a wall as well as in a watertight box.
Technical features
Type
001DC009AC
Power supply from BUS [V DC] 15-20
Consumption [max mA] 30
Consumption in stand-by mode [mA]
4
Max load to relay 5(2)A - 250 VAC
Storage temperature [°C] -25 ÷ +70
Operating temperature [°C]
0 ÷ +35
Features B
Terminal board a
BBus input
NC Contact normally closed
C1 Common Relay 1
NO Contact normally open
NC Contact normally closed
C2 Common Relay 2
NO Contact normally open
PROG LED
NC
TIMER
C2 NO
PROG
NC C1 NO
B
VLS/2
Made in Italy
ON
123
4 5 86 7
SW
OFF
ON
OFF
1234567 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
ON
OFF
ON
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
1234567 8
SW
OFF
ON
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
1234567 8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
1234567 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
1234567 8
SW
OFF
123456 7 8
SW
ON
OFF
ON
123456 7 8
SW
OFF
123456 7 8
SW
OFF
1234567 8
SW
OFF
1234567 8
SW
OFF
ON
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
1234567 8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
123456 7 8
a
A B
001DC009AC
Page 6 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
The device can be programmed manually in three ways. The type of pro-
gramming is identied by the number of Prog LED ashes:
- Individual programming (1 ash);
- Group programming (2 ashes);
- Global programming (3 ashes);
Each relay is furnished with a programming dip-switch:
- dip-switch 5 for relay 1;
- dip-switch 6 for relay 2;
Having chosen which relay to program congure dip-switches 3 and 4 for
programming.
Programming of the relays has to take place only once the installation has
been programmed.
Individual programming (each relay can be associated with up to 30
different users, e.g. user n° 5, 10 and 15)
- To choose which relay to program (DIP switch 5 ON programming of relay
1 aA, dip-switch 6 ON programming of relay 2) aB;
- Set dip-switch 3 to OFF and dip-switch 4 to ON ;
- At all internal intercoms press the button to be associated with the
command . Programming of each internal intercom will be indicated by
the ashing of LED.
To add additional internal intercom units simply repeat the programming pro-
cedure described above taking care not to lose the settings previously dened.
Group programming (each relay can be associated with a group of
consecutive users, e.g. users from n° 5 to n° 15).
- To choose which relay to program (DIP switch 5 ON programming of relay
1 aA, dip-switch 6 ON programming of relay 2) aB;
- Set dip-switch 3 to ON and dip-switch 4 to OFF e;
- Press the button to dedicate to command . on the rst and last
Dip-switch function
SW1.1
The door lock release command vis associated
with relay 1 The Aux 1 command is associated with relay 1 (default)
SW1.2
The TIMER potentiometer controls the action of one of
the two relays for a variable amount of time between
1 and 15 seconds
The TIMER potentiometer controls the action of one of the two
relays within a range of between 30 seconds and 8 minutes with
30-second intervals
SW1.3 - SW1.4
Choice of one of the three Manual Programmings
SW1.5
Relay 1 NOT being programmed Relay 1 manual programming
SW1.6
Relay 2 NOT being programmed Relay 2 manual programming
SW1.7
Manages the timer of relay 1 established in the SW
1.2 dip-switch Manages the timer of relay 2 established in the SW 1.2 dip-switch
SW1.8
Enabling for the receipt of commands from Manual
Programming
Enabling for the receipt of commands from Tool Programming
Manual programming
SW
OFF
ON
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
1234567 8
SW
ON
OFF
ON
123456 7 8
SW
OFF
1234567 8
SW
OFF
123456 7 8
SW
OFF
1234567 8
SW
OFF
ON
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
1234567 8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
ON
OFF
ON
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
1234567 8
SW
OFF
ON
OFF
ON
OFF
ON
SW
OFF
1234567 8
SW
OFF
1234567 8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
123456 7 8
e
SW
OFF
ON
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
ON
OFF
ON
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
1234567 8
SW
OFF
ON
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
1234567 8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
1234567 8
SW
OFF
ON
OFF
1234567 8
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
123456 7 8
a
SW
OFF
ON
OFF
1234567 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
ON
OFF
ON
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
1234567 8
SW
OFF
ON
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
1234567 8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
1234567 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
ON
OFF
ON
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
1234567 8
SW
OFF
ON
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
1234567 8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
OFF
ON
OFF
ON
SW
OFF
1234567 8
SW
OFF
1234567 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
1234567 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
ON
OFF
ON
123456 7 8
SW
OFF
123456 7 8
SW
OFF
123456 7 8
SW
OFF
1234567 8
SW
OFF
ON
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
1234567 8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
SW
OFF
ON
OFF
123456 7 8
OFF
ON
OFF
ON
SW
OFF
123456 7 8
SW
OFF
123456 7 8
Page 7 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Dip-switch settings following tool programming
Once a system containing a 001DC009AC has been programmed from the tool, dip switch SW1.8 on all the 001DC009AC devices featured in the system
must under all circumstances be set to ON.
Once SW1.8 has been set to ON, the remaining dip switches lose their previous meaning and take on a completely dierent one; this makes it possible to
install several 001DC009AC devices in a single branch, capable of reacting to dierent commands according to the following dip-switch settings.
Relay pair SW
relays 8-9
relays 10-11
relays 12-13
relays 14-15
Relay pair SW
relays 0-1
relays 2-3
relays 4-5
relays 6-7
- Set dip-switch 5 or 6 to the ON position a;
- Set dip-switches 3 and 4 to ON ;
- First set dip-switch 5 or 6 to the OFF position and then 3 and 4 to the
OFF position.
To reset to default settings
receiver. LED ashes to indicate that each receiver has been successfully
programmed.
y The command chosen has to be the same for each internal intercom. Any
eventual inconsistency in the choice of commands will entail reprogramming
of the actuator (see the paragraph ‘Return to default settings’).
Total programming (each relay can be associated with all users)
- To choose which relay to program (DIP switch 5 ON programming of relay
1 aA, dip-switch f ON programming of relay 2) aB;
- Set dip-switch 3 and 4 to OFF ;
- Press the button to dedicate to command . on any receiver. LED
ashes to indicate that each receiver has been successfully programmed.
- To exit programming set dip-switch 5 or 6 to OFF then dip-switch 3
and 4 to OFF.
48,5 mm
21 mm
60 mm
85,5 mm
69,5 mm
A
10
11
7
2
–
–
+
001DC011AC
a
Page 8 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
001DC011AC
Device description A
The 001DC011AC AC/DC converter is device designed for the installation
of audio receivers and video receivers coupled with a compatible gate
automatism equipped with an accessory output.
With just 4 wires that connect the gate with the audio receiver/video receiver
kit, the device not only supplies the kit but it also allows you to operate the
gate. Command 2-7 is executed by a clean contact (relay).
Technical features
Type 001DC011AC
Minimum input voltage (V AC) 20
Maximum input voltage (V AC) 25
Output voltage (V DC) 18
Output current (A) 1
Maximum operating relative humidity without
condensation 95
Storage temperature (°C) -25 ÷ +70
Operating temperature (°C) -15 ÷ +50
Features of terminals 2 - 7
Control voltage: 12V - 12.5 mA
Maximum switching voltage: 50 V AC or 75 V DC
Maximum switching power: 60VA - 24W
Function of terminals
–18V DC supply output
+
2Opening command output towards gate
7
10 Power supply input 20÷25V AC
11
–Opening command input from entry panel
A
E
C
254
99 25
281
127
1,2
254
99 25
281
127
1,2
a
B
D
500 mm
1190 mm
100°
870 mm
500 mm
50 mm
180 mm
65 mm
82°
Page 9 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Recessed installation (optional)
Wall in the recessed box at the desired height, respecting the positioning of
the lens of the surveillance camera B.
Push the pipe with the system conductors through one of the breaking
points Fa.
When installing the recessed box any possible deformations can be avoided
by using the spacer provided F.
Position the frame surround in the recessed box G, push the connection
wires through hole F a, hold the entry panel in place and attach it in a se-
mi-proud position H; take o the terminal covers and make the connections.
WARNING. The wires must be uncovered until flush with the wall and
inserted as shown in D (on the left the wires coming from the power
supply unit and on the right from those relating to service functions).
001DC01ENIGMA
Wall mounting
With the wall plugs provided x the entry panel A at the desired height
respecting the positioning of the lens of the surveillance camera B.
Push through pipe A a, take o the terminal board cover and make the
connections C.
WARNING. The wires must be uncovered until flush with the wall and
inserted as shown in D (on the left the wires coming from the power
supply unit and on the right from those relating to service functions).
Perform the programming and adjustment operations of the entry panel as
described to the chapter “Programming”.
Put back on the terminal board covers and assemble the front cover E.
H
J
G
A
B
2
1
a
F
a
i
2
1
e
h
i
Page 10 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Once the connections have been made, push the entry panel up slightly to
meet the frame I. Perform the programming and adjustment operations
of the entry panel as described to the chapter “Programming”. Put back on
the terminal board covers and assemble the front cover E.
Accessories J
a Single height button 001DC00EGMA11;
Double height button 001DC00EGMA12;
Double 001DC00EGMA13 button;
Single height plu 001DC00EGMA14;
e Double height stopper 001DC00EGMA16;
Access control module with keyboard 001DC00EGMA02;
Recessed box 001DC00EGMA10;
h Recessed frame 001DC00EGMA08,
i Wall roof 001DC00EGMA07
K
M1
CN4
M2
CN2
DATI
MINI USB
OUT
BOUT
PROG
eh
i
a
Page 11 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Functions K
Terminal boards a
+Power supply
14-18 VDC
–
BOUT Riser
Terminal boards
Solenoid lock
12 V - 1 A max
–
Door lock release button (NA)
Door contact input (NC)
–Ground
Entry panel enabling output (active towards earth)
–Ground
PROG key and PROG LED
Programming key and LED (see 'Programming' paragraph).
The PROG LED can take on the following states:
O
On
Slow ashing
Quick ashing
Adjustments e
loudspeaker audio
microphone audio
solenoid lock 1-10 s. (default 1 s)
Connectors
CN2: Connector for the keyboard or RFID access control module.
CN4: Additional push button panel connector.
h MINI USB: Programming connector.
Signals i
Red - Call in progress
Green - Door open
Yellow - Conversation in progress
Blue - System busy
Technical data
Type 001DC01ENIGMA
Power supply (VDC) 14-18
Absorption (mA) 320
Consumption in stand-by mode (mA) 130
Storage temperature (°C) -25 ÷ + 70
Operating temperature (°C) -15 ÷ +50
IP Degree 54
Camera 001DC01ENIGMA
Standard video PAL/NTSC
Resolution (pixel) 680x512
Minimum lighting (LUX) 1
1
G
212
TIMER
CAME gate
M1
CN4
M2
CN2
PROG
DATI
MINI USB
OUT
BOUT
CN1 IN
NC
TIMER
C2 NO
PROG
NC C1 NO
B
ON
1 2 3 4 5 86 7
M001DC008AC
001DC009AC
PROG
M1
CN4
M2
CN2
B
B
1 2
ON
3IN
OUT
>3’’
<6’’
a
B
A
C
1
2
3
4
5
6
7
8
9
10
Page 12 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Programming
The kit is pre-congured to manage a single call originating from a single entry panel. One or more receivers answering the same call can be added, by
following the below “Call button programming” procedure.
Initial programming
In the case that the call buttons are ONLY located on the ADDITIONAL PUSH BUTTON PANELS,
the operation illustrated in gure must be carried out as illustrated in gure C.
y
Accessing programming. Press the PROG key a for at least 3 sec and then release it within 6 s. If
the PROG LED turns o suddenly, this indicates a malfunction. Check the connections and return to
programming. The entry panel LEDs turn on as shown in the gure . Wait 5 seconds for the self-test
to be completed and then continue as described below.
Programming key type and address. Press the rst key on the entry terminal /A/B until
the LED stops ashing as does the backlighting LEDs .
Connection example M
e
beep
1-2-3
+
12345 beep
h
+ +
i
<1’’ PROG
M1
CN4
M2
CN2
B
B
1 2
ON
3IN
OUT
3
8
4
6
9
7
5
2
1
100 °
82 °
54 °
72 °
1÷9
0
Page 13 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Exiting programming. Briey press the PROG key on the power supplier i: the PROG LED and
entry panel LEDs will turn o. NOTE. If no action is performed, the procedure will automatically end
after 30 minutes.
Programming the entry panel surveillance camera. When programming the call buttons, the
camera’s “visual eld” can be adjusted from any extension (with the received lifted, if present), pressing
the “self-connection ” . Starting from the default conguration, it is possible to scroll the next
ones pressing the AUX1 key or return to the previous ones with the AUX2 key : the setting
will be automatically saved.
External entry panel illumination level adjustment. During the call button programming of any
internal receiver the external entry panel illumination level can be adjusted up or down (with the
handset lifted if present). Pressing the “self-connection ” button on the internal receiver causes
the external entry panel camera for which the illumination level is to be adjusted to be activated. At
this point, by means of the previously assigned call button (by call button or 001DC00EGMA02-03) the
illumination level can be either incremented or decremented.
Programming the door lock release code and 001DC00EGMA02-03-based relay. Press and key
in the relay code you wish to programme (press key 1 to activate the door opening control in the entry
panel; press key 2 to activate relay 1 on the 001DC009AC relay module; press key 3 to activate relay
2 on the 001DC009AC relay module . Press once again and key in the desired code (from 3 to 5
numbers) followed by the key h. Once programming has been completed, by pressing key and
the desired code and , it is possible to activate the door opening control, and activate relay 1 or 2.
Programming the call keys. Press the door lock release and AUX2 e buttons. On the entry panel,
press the call key to associate with the internal extension : an acoustic signal will conrm that the
setting was stored. Hang up the receiver again. Repeating the same operations for the other extensions.
PROG
M1
CN4
M2
CN2
B
B
1 2
ON
3IN
OUT
>3’’
<6’’
a
beep
1-2-3
e
+
h
<1’’ PROG
M1
CN4
M2
CN2
B
B
1 2
ON
3IN
OUT
PROG
M1
CN4
M2
CN2
B
B
1 2
ON
3IN
OUT
>3’’
<6’’
i
12345 beep
+ +
Page 14 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Programming the entry panel camera. When programming the call buttons, the camera’s “visual
eld” can be adjusted as previously described.
External entry panel illumination level adjustment. During call button programming the external
entry panel illumination level can be adjusted up or down as previously described.
In the case that the call buttons are ONLY located on the ADDITIONAL PUSH BUTTON PANELS,
proceed as indicated in NOTE on page 12.
Reprogramming procedure
Accessing programming. Press the PROG key a for at least 3 sec and then release it within 6 s. If
the PROG LED turns o suddenly, this indicates a malfunction. Check the connections and return to
programming. The entry panel LEDs turn on as shown in the gure . Wait 5 seconds for the self-test
to be completed and then continue as described below.
Programming the call keys. Press the door lock release and AUX2 buttons. On the entry pa-
nel, press the call key to associate with the internal extension : an acoustic signal will conrm that the
setting was stored. Hang up the receiver again. Repeating the same operations for the other extensions.
Programming the door lock release code and 001DC00EGMA02-03-based relay. Press and key
in the relay code you wish to programme (press key 1 to activate the door opening control in the entry
panel; press key 2 to activate relay 1 on the 001DC009AC relay module; press key 3 to activate relay
2 on the 001DC009AC relay module e. Press once again and key in the desired code (from 3 to 5
numbers) followed by the key . Once programming has been completed, by pressing key and
the desired code and , it is possible to activate the door opening control, and activate relay 1 or 2.
Exiting programming. Briey press the PROG key: the PROG LED and entry panel LEDs will turn o. If
no action is performed, the procedure will end automatically after 30 minutes.
Programming key type. During the “Call button programming” phase press the PROG key h for
at least 3 sec and then release it within 6 s. until accessing the “Programming key type” procedure i.
Press one of the rst 4 “keys” on the entry panel, the LED will stop ashing as will the backlighting
LED of the rst 4 call key positions j. The signals will assume the conguration . At the end, exit
programming, briey press the PROG key : the PROG LED and the entry panel LEDs will turn o. If
no action is performed, the procedure will end automatically after 30 minutes.
a
a
 
001DC008AC
A
1
2
1
2
M1
001DC009AC
NC
NO
C1
NC
NO
C2
B
SW
OFFOFF
ON
1234567 8
+
BOUT
-
+
-
M1
001DC02LUXO
CL.RES
+
AL
A
-
V
001DC01ENIGMA
+
BOUT
-
-
-
-
M2
M1
001DC008AC
2
001DC008AC
001DC008AC
2
2
2 2
2
2
001DC012AC 001DC012AC
2
2
2
2
2
2
001DC012AC 001DC012AC
001DC012AC 001DC012AC
2
2
001DC011AC
4
4
10
11
7
2
–
–
+
001DC011AC
CAME GATE
001DC009AC
001DC008AC
2
001DC008AC
001DC008AC
2
2
22
2
2
001DC012AC 001DC012AC
2
2
2
2
2
2
001DC012AC 001DC012AC
001DC012AC 001DC012AC
2
2
001DC011AC
4
4
10
11
7
2
–
–
+
001DC011AC
CAME GATE
001DC009AC
001DC008AC
2
001DC008AC
001DC008AC
2
2
2 2
2
2
001DC012AC 001DC012AC
2
2
2
2
2
2
001DC012AC 001DC012AC
001DC012AC 001DC012AC
2
2
001DC011AC
4
4
10
11
7
2
–
–
+
001DC011AC
CAME GATE
001DC009AC
001DC008AC
2
001DC008AC
001DC008AC
2
2
2 2
2
2
001DC012AC 001DC012AC
2
2
2
2
2
2
001DC012AC 001DC012AC
001DC012AC 001DC012AC
2
2
001DC011AC
4
4
10
11
7
2
–
–
+
001DC011AC
CAME GATE
001DC009AC
Page 15 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Connection examples
+
BOUT
-
-
-
-
M2
001DC008AC
A
1
2
1
2
M1
–
+18V
230V
PRI
SEC
+ 18V –
230V
230V 50Hz 18V 10VA
001DC012AC
M1
001DC01ENIGMA
001DC02LUXO
CL.RES
+
+
BOUT
AL
A
-
-
V
-
+
M1
001DC02LUXO
CL.RES
+
+
BOUT
AL
A
-
-
V
-
+
M1
–
+18V
230V
PRI
SEC
+ 18V –
230V
230V 50Hz 18V 10VA
001DC012AC
001DC02LUXO
CL.RES
+
+
BOUT
AL
A
-
-
V
-
+
M1
Page 16 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
2
12
OUT
SW2
SW4
SW3
001DC006AC
34
IN
SW0
1
+
BOUT
-
+
-
M1
–
+18V
230V
PRI
SEC
+ 18V –
230V
230V 50Hz 18V 10VA
001DC012AC
001DC02LUXO
CL.RES
+
+
BOUT
AL
A
-
-
V
-
+
M1
2
–
+18V
230V
PRI
SEC
+ 18V –
230V
230V 50Hz 18V 10VA
001DC012AC
001DC02LUXO
CL.RES
+
+
BOUT
AL
A
-
-
V
-
+
M1
–
+
18V
230V
PRI
SEC
+ 18V –
230V
230V 50Hz 18V 10VA
001DC012AC
001DC02LUXO
CL.RES
+
AL
A
-
V
1
+
BOUT
-
+
-
M1
–
+
18V
230V
PRI
SEC
+ 18V –
230V
230V 50Hz 18V 10VA
001DC012AC
001DC02LUXO
CL.RES
+
AL
A
-
V
001DC01ENIGMA
+
BOUT
-
-
-
-
M2
M1
001DC008AC
A
1
2
1
2
M1
Page 17 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
+
-
-
11
10
7
2
2
7
10
11
001DC01ENIGMA
+
BOUT
-
M1
-
-
-
M2
2
001DC02LUXO
CL.RES
+
+
BOUT
AL
A
-
-
V
-
+
M1
001DC011AC
CAME GATE
10
11
7
2
–
–
+
001DC011AC
Page 18 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Lb Ld
La
001DC006AC
Lc
001DC01ENIGMA
001DC011AC
001DC012AC001DC012AC
001DC008AC
Page 19 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Distances
VCM/1D VCM/2D UTP/CAT 5 2x1,5mm2
La+Lb ≤100 m – ≤100 m –
Lc ≤75 m – – ≤100 m
L1, L2, L3 – ≤100 m – –
L1+L2+ L3 – ≤300 m – –
La+Lb+L1(L2, L3) ≤150 m
La+Lb+L1+L2+L3 ≤600 m
Ld ≤100 m ≤75 m
CAME S.p.A.
Via Martiri Della Libertà, 15
31030 Dosson di Casier - Treviso - Italy
tel. (+39) 0422 4940 - fax. (+39) 0422 4941
Page 20 - Manual FA00964-EN - vers. 1 - 11/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
/