SOC-320(P)
Installing Manual
Manuel d’installation
Montageanleitung
Manuale d’installazione
Manual de instalación
Installatiehandleiding
Manual de instalação
Installationsvejledning
Installationsbruksanvisning
àÌÒÚÛ͈Ëfl ÔÓ ÛÒÚ‡ÌÓ‚ÍÂ
E
F
D
I
Es
NL
PT
DK
S
R
2
3
Important Safety Instructions
E E
6. If this product fails to operate normally, contact the store of purchase or
your nearest service center. Never disassemble or modify this product in any
way. (The manufacturer is not liable for any damage resulting from
unauthorized disassembly or repairs.)
7. When cleaning, do not spray water directly onto parts of the product. (Doing
so may cause fire or electric shock.) Wipe the surface with a dry cloth.
Never use detergents or chemical cleaners on the product, as this may result
in discoloration of surface or cause damage to the finish.
1. Do not drop objects on the product or apply strong shock to it. Keep away
from a location subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50
°C/
122
°F
),
low temperature (below -10
°C/
14
°F
), or high humidity. (Doing so may cause
fire or electric shock).
3. Avoid a location which is exposed to direct sunlight, or near heat sources
such as heaters or radiators. (Neglecting to do so may result in a risk of fire).
4. If you want to relocate the already installed product, be sure to turn off the
power and then move or reinstall it.
5. Install in a well - ventilated location.
6. Remove the power plug from the outlet when there is a lightning storm.
(Neglecting to do so may cause fire or damage to the product.)
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER
SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED
SERVICE PERSONNEL.
1. Make sure that the cable is plugged in securely before using.
(A loose connection may result in fire.)
2. When installing the camera on a wall or ceiling, mount it safely and
securely. (A falling camera may cause personal injury.)
3. Do not place conductive objects (e.g., screwdrivers, coins, and
metal things) or containers filled with water on top of the camera.
(Serious injury may result from fire, electric shock, or falling objects.)
4. Do not install in a sooty, dusty, or humid location.
(Doing so may cause fire or electric shock.)
5. If any unusual smells or smoke come from the unit, stop using the
product. In such case, immediately disconnect the power source and
contact the service center. (Continued use in such a condition may
cause fire or electric shock.)
This symbol indicates high voltage
is present inside. It is dangerous
to make any kind of contact with
any inside part of this product.
This symbol alerts you that
important literature concerning
operation and maintenance has
been included with this product.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
4
5
Table of Contents
E E
Chapter 1 Important Safety Instructions 2
Chapter 2 A look at the SOC-320(P)
Introduction of the SOC-320(P) Camera 5
Chapter 3 Before Installing SOC-320(P)
Check the Contents of the Package 6
Notice for Installation & Operation 7
Chapter 4 Installing the SOC-320(P)
Installing the SOC-320(P) 8
Chapter 5 Specifications for Outer Connector Pin
Pin arrangement for the SOC-320(P) RJ-45 connector of
11
Appendix SOC-320(P) Product Specification
SOC-320(P) Product SPEC 12
A look at the SOC-320(P)
The SOC-320(P) camera uses the VPP system exclusively manufactured by Samsung
Electronics.
It is not compatible with other products and will not in conjunction with them.
The camera is easy to install, even for general users, has a built-in microphone, and uses a
Varifocal AI (Auto iris) lens to produce the desired picture.
The Auto Iris has been installed to eliminate the Color Rolling effect, and generates clear pic-
tures without flicker at locations with different power frequencies.
What is Color Rolling? Non-periodical changes in color (to red, cyan, and yellow,
etc) due to unstable color temperature. This is caused by
the repeated flickering of mechanical fluorescent lamps
corresponding to the power frequency.
Occurrence of Color Rolling. Color Rolling can occur in environmens with mechanical
fluorescent lamps, with manual Iris installation, and with
the shutter speed set at ELC (Electronic Level Control).
What is Flicker? The Human eye can detect flickering when the contrast
repeat frequency is low. This effect is called flicker. Flicker
is serious when the vertical synchronizing frequency dif-
fers from the ON/OFF frequency of fluorescent light. This
situation occurs when using an NTSC camera at locations
where the power frequency is 50Hz and/or when using a
PAL camera at locations where the power frequency is
60Hz.
What is FL Mode? Fixing the shutter speed at 1/100(NTSC) or 1/120(PAL) to
prevent flicker at locations with different power frequen-
cies.
Introduction of the SOC-320(P) Camera
E
7
E
Check the Contents of the Package
Notice for Installation & Operation
Please make sure the following items (camera, accessories, cables, bracket,
and user's guide) are included in your SOC-320(P) package.
A
C
C
E
S
S
O
R
IE
S
6
Before Installing SOC-320(P)
✔ Confirm before installation that the chosen location can bear more than five
times the camera’s weight (approximately 1 Kg).
✔ Take care not to allow the cable to become trapped between parts, and make
sure the cable insulation is undamaged. (May cause malfunctions and/or fire)
✔ Be careful not to drop equipment while doing the installation and keep people
and valuables away from the area underneath.
✔ Install the SOC-320(P) in a cool location away from direct sunlight.
Do not expose the SOC-320(P) to direct sunlight at any time.
✔ Use the SOC-320(P) in environments with stable temperature and humidity
ranges as suggested below
- Temperature: -10°C ~ +50°C (14°F~122°F)
- Humidity: Below 90%
Camera
Bracket Accessories User Manual
Cable
9
EE
8
Installing the SOC-320(P)
1. Find a suitable place for installing the camera. (Must be able to bear five times
the weight of the camera [approx. 1Kg])
2. Install the Mounting Bracket provided at the
desired location, and assemble the camera onto
the bracket. Then connect the cable to the RJ-45
connector.
3. Plug the other end of the cable that is connected to the camera into the monitor.
4. Use the Handle on the Mounting Bracket when
adjusting the direction of view.
5. Adjusting Zoom and Focus
5-1. Turn the lens part of the camera in the direction shown in the picture and pull
to separate the lens -hood.
Installing the SOC-320(P)
5-2. Use the lens Zoom Lever to set the desired zoom
position.
5-3. After setting this position, adjust the Focus Lever
to get the picture into focus.
5-4. When the zoom and focus settings are finished,
rotate the Zoom and Focus Levers to fix the lens
in position.
5-5. After the adjustment, put the lens hood onto the
camera body and rotate it in the locking direction
to connect it.
10
E
11
E
Specifications for Outer Connector Pin
1DATA+
2 VIDEO_OUT
3 GND
4DATA-
5 AUDIO_OUT
6 VDD
7 GND_V
8 CH_SEL
8 ... 1
6. Setting the brightness (Iris setting)
The Iris is adjusted in the factory prior to ship-
ping; however, users may need to adjust the
opening and/or closing of the Iris according to the
position of installation, and ambient light condi-
tions. Use the Level VR located on the back of
the camera to optimize conditions.
7. Selecting FL-MODE Switch
This function key is used to switch the anti-flicker
function ON/OFF.
Flicker effect occurrence (due to power frequen-
cy differences) may be eliminated by turning this
Key ‘ON’.
8. After the camera lens has been adjusted, use the camera mount bracket to the
direction you want to monitor and then fasten it tight.
Installing the SOC-320(P)
Pin No. Pin Arrangement
Pins indicated with ‘★’ are not used.
★
★
★
Pin arrangement for the SOC-320(P) RJ-45 connector
E
12
ITEM
DESCRIPTION
SOC-320N SOC-320P
Product Type
Varifocal DC Auto Iris Type Normal camera Varifocal DC Auto Iris Type Normal camera
Power Source Voltage DC 12 ~ 18V From Monitor DC 12 ~ 18V From Monitor
Power Consumption Approx. 2W Approx. 2W
Broadcast System NTSC Standard Color Camera PAL Standard Color Camera
Image Device 1/4 inch IT Super HAD CCD 1/4 inch IT Super HAD CCD
Effective Pixel 510(H) X 492(V) 500(H) X 582(V)
Scanning Method 525 Line, 2:1 Interlace 625 Line, 2:1 Interlace
Line Frequency Horizontal : 15,734Hz Horizontal : 15,625Hz
Vertical : 60Hz Vertical : 50Hz
Synchronization Method INT INT
Resolution 330 TV Lines 330 TV Lines
S/N Ratio Over 48dB Over 48dB
Minimun Sence Illumination
2 Lux(F2.0 50IRE) 2 Lux(F2.0 50IRE)
Color Temperature ATW ATW
Electronic Shutter ELC ELC
Signal Output Composite Video Out : 1.0Vp-p Composite Video Out : 1.0Vp-p
75 Ohms/RJ45 Jack 75 Ohms/RJ45 Jack
Lens
3.4 ~ 9.0mm F:1.6 Varifocal DC Auto Iris
3.4 ~ 9.0mm F:1.6 Varifocal DC Auto Iris
Operating Temperature -10°C +50°C -10°C +50°C
Operating Humidity ~90% ~90%
Physical Size 62.5(W)X51(H)X119.5(L) 62.5(W)X51(H)X119.5(L)
Weight Approx. 170g Approx. 170g
SOC-320(P) Product Specification
SOC-320(P) Product SPEC
ELECTRONICS
Part No. AB68-00435A
Printed in Korea
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
AVer CC30 Camera Mount Installation guide
-
Xiaomi Yi Action Camera User manual
-
-
CNB BM7563NIR/BM7563PIR Owner's manual
-
D-Link DCS-7410 Datasheet
-
Elvox 46216.212 Operating instructions
-
Vista VVRD4V9DN Installation Instructions Manual
-
ACTiSYS CAM-6500 User manual
-
Pelco EH6500 User manual
-
COP-USA CD39IPZM-9545S2 Owner's manual
