THANK YOU
We appreciate the trust and condence you have placed in Commercial Electric through the purchase of this wall
mount. We strive to continually create quality products designed to enhance your home. Visit us online to see our full
line of products available for your home improvement needs. Thank you for choosing Commercial Electric!
USE AND CARE GUIDE
WALL MOUNT COMPONENT SHELF
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Item #1002 263 937
Model #50501
2
Table of Contents
Table of Contents ....................................................... 2
Safety Information ..................................................... 2
Warranty.....................................................................2
Pre-Installation ..........................................................3
Installation .................................................................5
Safety Information
Before you begin, make sure you carefully read and
understand the instructions in this manual. Please follow
the instructions in the order presented in this manual and
observe all warnings and cautions.
WARNING: A Warning alerts you to the possibility of
serious injury or death if you do not follow the instructions.
This wall mount has been tested to support equipment
with a weight up to 17.6 lbs (8 kgs).
WARNING: This wall mount is intended for use only
with the maximum weights indicated. Use with products
heavier than the maximum weights indicated may result in
collapse of the mount and its accessories causing possible
injury. This mount has been tested to support 17.6 lbs. (8
kgs). Do not exceed this weight.
WARNING: Observe all safety measures at all times
during the installation of this product. Use proper safety
gear and tools during the installation process to prevent
physical injury.
WARNING: Check that the bracket is secure and safe to
use at regular intervals (at least every 3 months).
WARNING: Failure to provide adequate structural
strength for this component can result in physical
injury and/or damage to equipment. It is the installer’s
responsibility to make sure the structure to which
this component is attached can support the combined
weight of the equipment and all attached hardware and
components.
WARNING: This product was designed to be installed
and utilized ONLY as specied in this manual. Improper
installation may cause damage or serious injury.
WARNING: This product should only be installed by
someone with good mechanical ability who has basic
building experience and fully understands this manual.
WARNING: If mounting to wood wall studs, make sure
the mounting screws are anchored into the center of the
studs. The use of a stud nder is highly recommended.
WARNING: Always use an assistant or mechanical lifting
equipment to safely lift and position the equipment.
WARNING: Tighten screws rmly but do not over-
tighten. Over-tightening can cause damage to the product.
This greatly reduces the holding power.
WARNING: This product is intended for indoor use only.
Using this product outdoors could lead to product failure
and personal injury.
CAUTION: A Caution alerts you to the possibility of
damage to or destruction of the equipment if you do not
follow the corresponding instructions.
CAUTION: Do not install on a structure that is prone to
vibration, movement or chance of impact. Doing so could
result in damage to the mounting surface.
Warranty
The manufacturer warrants that it will replace or repair this item, free of charge, at the manufacturer’s sole
discretion, should it prove defective in materials or workmanship.
If a claim is made under this warranty, the mount should be returned, freight prepaid, with the original purchase
receipt to your dealer.
This warranty does not apply to:
□ Normal wear and tear
□ Friction damage
□ Coating defects
□ Defects caused by loosened screws, nuts, or bolts
□ Improperly mounting the bracket to the wall
□ Improperly installing the bracket to the equipment
□ Failure to properly follow installation
instructions
□ Modication or repairs not made or authorized
by the manufacturer
□ Loading beyond permitted load
□ Intentional misuse
Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.
3 HOMEDEPOT.com
Please contact 1-877-527-0313 for further assistance.
Pre-Installation
PLANNING INSTALLATION
Compare all parts in the package with the Hardware Included and Package Contents lists in this manual. If any part
is missing or damaged, do not install this wall mount system and call customer service at 1-877-527-0313.
PLANNING WALL PLACEMENT
CAUTION: Ensure the wall you select is a weight-bearing wall. Failure to observe this precaution can result in serious physical injury
and/or property damage. Consult a professional installer or contact customer service if you have any questions.
When selecting a wall to mount your audio/video components, keep the following in mind:
□ Select a place with easy access to power outlets, cable input sources, and connections for speakers and
accessories.
□ Avoid direct sunlight, heat, and vibrations and do not place in direct ow of trafc.
□ Select a weight-bearing wall. The wall must be able to safely support four times the combined load of the
equipment and all attached hardware and components.
11.02 in.
280 mm
14.96 in.
380 mm
3.15 in.
80 mm
0.78 in.
20 mm
8.66 in.
220 mm
ENSURING WALL STABILITY
Carefully inspect the wall area you have selected. Examine the wall surface before you begin drilling.
WARNING: Do not drill near electrical wiring and water pipes.
□ For concrete walls, check for damaged or loose concrete and do not drill in those areas.
□ For brick wall, never drill into the mortar between blocks.
□ For wood studs, locate the wall studs and drill in the center of the stud.
TOOLS REQUIRED (NOT INCLUDED)
Power
drill
5/32 in. (4 mm)
wood drill bit or
5/16 in. (8 mm)
masonry drill bit
Phillips
screwdriver
Level Pencil
Stud
nder
Tape measure Hammer
Safety
glasses
4
Pre-Installation (continued)
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
NOTE: The hardware included is suitable for mounting to walls made of brick, solid concrete, or wood studs covered with drywall.
If your mounting situation is different, please consult a qualied installer or contact customer service at 1-877-527-0313 or visit
www. HomeDepot.com.
AA BB CC DD EE FF
Part Description Quantity
AA Lag bolt 2
BB Concrete anchor 2
CC M5 bolt 3
DD Plastic button 1
EE Plastic cap 2
FF 3 mm Allen key 1
PACKAGE CONTENTS
A
C
D
E
B
Part Description Quantity
A Tempered glass shelf 1
B Glass holder 1
C Wall plate 1
D Connector 1
E Decorative cover 2
5 HOMEDEPOT.com
Please contact 1-877-527-0313 for further assistance.
Installation
1
Installing the wall plate
(wood stud)
If you are installing this mounting system in brick
(concrete), proceed to step 2.
CAUTION: Avoid drilling near electrical wiring and water
pipes. The mounting system must be attached to a weight
bearing wall and must be installed directly onto the center
of the wood studs. Failure to observe all safety precautions
can result in serious physical injury and/or property
damage. Consult a professional installer or call customer
service if you have any questions.
CAUTION: Tighten the screws so that the wall plate is
rmly attached. Do not overtighten. Over-tightening can
damage the screws, greatly reducing the holding power.
CAUTION: Wood studs must be no smaller than 2 x 4
in. in size.
□ Use a commercially-available stud nder to
locate the stud centers in the wall. Studs are
usually spaced 16 in. apart.
□ Use the wall plate (C) as a template to mark
the installation holes. Use a level to ensure the
plate is level.
□ Use a 5/32 in. (4 mm) wood drill bit to drill 2 in.
(50 mm) pilot holes.
□ Position the wall plate (C) over the installation
holes. Ensure that the plate is level and then
attach using the lag bolts (AA).
C
AA
2
Installing the wall plate
(concrete/brick walls)
CAUTION: Avoid drilling near electrical wiring and water
pipes. The mounting system must be attached to a weight
bearing wall. Failure to observe all safety precautions can
result in serious physical injury and/or property damage.
Consult a professional installer or call customer service if
you have any questions.
CAUTION: Do not drill in mortar between bricks or into
loose concrete. Never drill into hollow brick.
□ Use the wall plate (C) as a template to mark
the installation holes. Use a level to ensure the
plate is level.
□ Use a 5/16 in. (8 mm) masonry drill bit to
slowly drill 2.2 in. (55 mm) pilot holes.
□ Insert anchors (BB) into the holes. Ensure the
anchors are completely ush to the concrete
surface even if covered by a layer of joint
compound or other material.
□ Position the wall plate (C) over the installation
holes. Ensure that the plate is level and then
attach using the lag bolts (AA).
BB
A
A
C
6
Installation (continued)
3
Attaching the connector to the
glass holder
□ Position the connector (D) along the center
piece of the glass holder (B) and connect
the two pieces together using two M5 bolts
(CC). Loosely tighten using the wrench (FF),
ensuring there is a 3 mm space between the
connector (D) and glass holder (B). This will
allow you to more easily slide this assembly
onto the wall plate.
3 mm
D
B
FF
B
D
CC
4
Installing the glass holder
□ Slide the connector (D) portion of the glass
holder (B) down into the top of the wall plate
(C).
□ When you reach the desired position for the
glass holder (B) along the wall plate (C), secure
the holder (B) in place by tightening the bolts
(CC) using the wrench (FF).
□ Attach the decorative covers (E) on each end
of the wall plate (C) and plastic caps (EE) over
the two mounting holes on the wall plate (C),
as shown.
□ (Optional) To adjust the height of the glass
holder (B), loosen the bolts (CC) and move the
holder (B) up or down along the wall plate (C),
as desired. Re-tighten the bolts (CC) when
nished.
CC
E
EE
FF
B
D
C
7 HOMEDEPOT.com
Please contact 1-877-527-0313 for further assistance.
Installation (continued)
5
Installing the glass shelf
□ Place the glass shelf (A) onto the wall plate
assembly, as shown.
□ Secure the glass shelf (A) in place using a
plastic button (DD) and M5 bolt (CC). Tighten
using the wrench (FF).
CAUTION: Do not overtighten the M5 bolt.
DD
FF
CC
A
6
Placing your component on the
wall mount
□ Gently place your component (not included) on
the wall mount, as shown.
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.
/
