LBL Lighting SU768SCLED830 Installation guide

Brand: LBL Lighting

Model: SU768SCLED830

Type: Installation guide

Installation Instructions for

Calix 7-Light Suspension ( )LED

1.1

980 7SCALIX

Suspension

768_SU

GP I :ENERAL RODUCT NFORMATION

This product is suitable for damp locations.

This product may be dimmed with a low-voltage electronic dimmer.

Determine the desired location fixture and center the canopy to the electrical box.

Ensure that the power cord port will be aligned with the canopy’s thumb screw and the locations of the two aircraft cable

posts as illustrated above.

While ensuring that the fixture’s location is aligned accordingly, make two aircraft cable post location marks 10.625” away

from the center of the power cord post.

Install the Fixture

AIRCRAFT CABLE POST LOCATION AIRCRAFT CABLE POST LOCATION

THUMB SCREWPOWER CORD POST

10.625” 10.625”

Tap the anchor at the marked point up to the threaded portion with a hammer.

Screw the anchor in the rest of the way with a Phillips screwdriver.

ANCHOR

CEILING

CAUTION RISK OF FIRE-

This product must be installed in accordance with

the applicable installation code by a person familiar

with the construction and operation of the product

and the hazards involved.

Use minimum 90°c supply conductors.

Prepare the Canopy

#8-32

SCREW

CROSSBAR

Mount the crossbar assembly to the electrical box with

the two provided #8-32 screws.

2 2

Screw the cable post completely to the threaded nipple.

CABLE POST

THREADED NIPPLE

Feed the aircraft cables through the cable post to the desired

length.

To level the fixture, push the tab on the cable clutch and feed

more or less of the support cable into the cable clutch. Make

fine adjustments to each cable until the fixture is level.

If necessary, trim the excess cable from the cable post.

CAUTION: Make sure to support the fixture while

making adjustments, an assistant will be needed to

complete this step.

CABLE CLUTCH

CABLE POST

AIRCRAFT CABLE

Remove the crossbar from the canopy by completely

unscrewing the thumb screw.

CROSSBAR

POWER

CORD

THUMB SCREW

CANOPY

Shorten the Power Cord (optional)

Take note of the wire connections and remove the wire nuts

to disconnect the power cord wires from the driver wires.

POWER

CORD

DRIVER

POWER

CORD

STRAIN

RELIEF

SET SCREW

Loosen the 2 set screws on the strain(Do Not Remove)

relief.

Pull the power cords through the strain relief to the

desired length and re-tighten the 2 set screws.

Leave at least 6” of cord in the back of the canopy for

wire connections and trim off the excess cable.

From the end of the cord, strip the insulation 4" using a

sharp knife. .Make sure not to nick the inner wires

Strip the end of the wires.

Reconnect the power cord wires to their original

connections to the driver (reversal of 2A).

Install the Canopy

Ground the fixture to a suitable ground in accordance

with local electrical codes.

Connect the white driver wire to the neutral power line

wire.

Connect the black driver wire to the hot power line

wire.

POWER

CORD

DRIVER

SAVETHESE INSTRUCTIONS!

7400 Linder Ave, Skokie, 60077IL

800.323.3226 - 847.626.6300

www.lbllighting.com

registered trademark of Lighting. Lighting reserves the right toLBL LBL

change specifications for product improvements without notification.

A Generation Brands Company

Properly place the driver, all wires, and wire connections into

the electrical box.

Mount the canopy to the crossbar by completely screwing in

the thumb screw.

THUMB SCREW

NOTE: If installing the canopy onto a electrical box

with a plaster ring, loosen the screws to the crossbar

to insert the driver into the electrical box, then re-

tighten the screws the screws to the crossbar.

Adjust the Heads

Rotate the heads to the desired direction.

LBL Lighting SU768SCLED830 Installation guide

LBL Lighting SU768SCLED830 Installation guide

LBL Lighting SU768SCLED830 Installation guide

Related papers

Other documents