Pipistrel Sinus Build Manual

Type
Build Manual

This manual is also suitable for

K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Pipistrel
Sinus & Virus
Kit Build Manual
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 1 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Table of Contents
What do you need?......................................................................................................................................4
Preparing the Fuselage .............................................................................................................................. 5
Preparing the undercarriage.....................................................................................................................10
Fitting the undercarriage to the aircraft...................................................................................................18
Firewall setup ............................................................................................................................................ 21
Mounting the engine to the firewall..........................................................................................................22
Sound dampening material ...................................................................................................................... 23
Painting the fuselages interior (part 1) ................................................................................................... 25
General touch ups and painting the fuselage (part 2)............................................................................27
Lining the fuselage interior with carpet and mounting the fuel taps....................................................29
Fitting the cockpit carpet .......................................................................................................................... 32
Installation of the heat duct, oil tank bracket and wire bundle fittings.................................................33
Cutting the slots for the fuel gauge ......................................................................................................... 34
Fitting the throttle assembly and the flap handle ................................................................................... 34
Fitting the ballistic chute (part 1) ............................................................................................................. 37
Fitting the ballistic chute (part 2) ............................................................................................................. 43
Fitting the lower fuel system .................................................................................................................... 49
Fitting the Velcro for the seats..................................................................................................................54
Rudder pedal preparation ......................................................................................................................... 55
Seat belt preparation..................................................................................................................................56
Drilling the rudder cable holes..................................................................................................................58
Running the rudder cable outers..............................................................................................................58
Mounting the pedals ................................................................................................................................. 61
Fitting the rudder cables .......................................................................................................................... 69
Mounting the upper flaperon pushrod bracket.......................................................................................70
Mounting the electrical panel ................................................................................................................... 71
Fitting the rudder assembly ..................................................................................................................... 72
Horizontal stabilizer preparation..............................................................................................................81
Preparing the elevator / rudder ................................................................................................................ 83
Fitting the horizontal stabilizer ................................................................................................................ 88
Installation of the sliding elevator trim knob .......................................................................................... 93
Fitting the trim system .............................................................................................................................. 95
The Control System .................................................................................................................................. 98
Mounting the control system..................................................................................................................102
Nose wheel cable preparation ................................................................................................................ 107
Finishing the rudder cables ................................................................................................................... 109
Fitting the rudder .................................................................................................................................... 110
Fitting the brake lines ............................................................................................................................. 111
Mounting the fuel lines in the cabin ...................................................................................................... 117
Fitting the windscreen ............................................................................................................................ 118
Installation of the strobes ....................................................................................................................... 123
Fitting the engine (part 1) ....................................................................................................................... 126
Fitting the engine (part 2) ....................................................................................................................... 167
Fitting the dashboard ............................................................................................................................. 175
Fitting the front cowls ............................................................................................................................. 178
Fitting the cowling around the exhaust and final cowl touch ups ...................................................... 187
Propeller setup ........................................................................................................................................ 191
Fitting the nose wheel ............................................................................................................................ 196
Wing preparation ..................................................................................................................................... 197
Assembling the airbrakes........................................................................................................................215
Mounting the wings ................................................................................................................................ 223
Fitting the Wheel Spats ........................................................................................................................... 229
Fitting the nose wheel spat .................................................................................................................... 233
Fitting the luggage rack and headsets...................................................................................................234
Mounting the Autopilot System..............................................................................................................237
Automatic nose wheel and rudder centering systems ........................................................................ 245
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 2 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Congratulations on your purchase or evaluation of the Pipistrel Sinus or Virus aircraft kit.
The Sinus and Virus are unique aircraft, providing exceptional performance, unparalleled
flying qualities and astonishing economy.
The building procedures explained in this manual are aimed towards the abilities of an average
person with basic tools. Most of the precision manufacture has been performed at the factory
under controlled conditions, and this will provide the homebuilder with an aircraft which should
be every bit as good as a factory manufactured plane.
Most of the construction can be performed by the builder alone, but you will require additional
assistance for some tasks. Possibly a friend or partner could assist you with some of the
construction. In situations, where you need to rotate the fuselage or fit the wings, you may
need three people.
By following these simple instructions and the accompanying photographs, we expect that you
will need around 250 to 400 hours of enjoyable construction to finish the aircraft. Should you
have any questions with this manual or the construction techniques please contact Pipistrel USA
for clarification. If you aren't used to the metric system, be sure to check Appendix 1 where we
have added a conversion table to help you with certain measurements.
As this is a new version of the kit manual for Pipistrel's Sinus and Virus rcraft, we would like your
feedback and suggestions on the different tasks, so we may improve the manual for future
customers. Please email [email protected]m with any of your questions
They say a picture is worth 1000 words... so we have tried to incorporate this in our manual and
let the pictures do the talking. With over 1000 deruddered images to select from and print out
you will probably find many answers to your questions in the photos and accompanying text.
Time to build..... Lets start !!
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 3 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
What do you need?
Space
Pipistrel Sinus aircraft have a wingspan of just under 15 meters, while Virus aircraft have
approximately 12.5. In order to work the wings comfortably, you're going to need a work space
that is at least 9 meters long, because Sinus wings measure approximately 8 meters long. This
would give you a little space at each end to move around a little more if you're making a Virus.
Work Conditions
Working with epoxy requires, that the components epoxy and work space need to be around 21
degrees Celsius until the epoxy completely cures. For all other steps and procedures you aren't
required to heat your workspace.
Work Conditions
Here is a list of tools that will definitely come in handy when making your Pipistrel aircraft:
Vapor mask Tape measure
Variable speed drill Swaging tool
Set of metric drill bits (longer ones if possible) Work lamp (one that you can hang in the aircraft if
need be)
Metric thread taps Scissors or clippers
Metric step drill Paint brushes
Standard metric open-end wrenches Dremel hand drill
Standard metric ratchet sockets Dremel sanding drill bits
Standard metric Allen wrenches Heat gun
Special NutSert installation tool Various files for sanding, grinding and polishing
Right angle hand drill (or drill angle attachment) Felt-tip marker (erasable)
Jigsaw Drill bits for countersinking
De-burring tool Vernier caliper set
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 4 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Materials
Here is a list of materials that you will definitely need when making your Pipistrel aircraft:
Loctite 243
Loctite 262
Sheets of plastic for masking while painting (3M
Painter's Masking Tape Pre-Taped Drop Cloth is highly
recommended)
Grease (SKF bearing grease or Xintex)
Silicon (black if possible)
WD-40
Sandpaper (80 and 100 granulation)
Electrical tape
Two-sided tape
Rubber gloves
Preparing the Fuselage
Support the fuselage on a suitable stand and support the rudder on a piece of foam to
protect it from damage.
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 5 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Mask the elevator pushrod with masking tape to keep out dust and debris from the
pushrod bearings during the early fuselage preparation phases.
Sand the cockpit openings smooth to remove the sharp edges from manufacture
Sand the windscreen edge to ensure a good fit of the Lexan windscreen, paying particular
attention to the section marked with ovals in the photos below. The key is to make sure
the edges around the windscreen are smooth and not sharp.
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 6 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
The sections highlighted below need a little extra material taken off the inside edge to
make sure the windscreen seats perfectly. Be sure to do both sides.
With a marker pen, mark the center of the fuselage halves above the firewall section.
Look for the strip of raised plastic on the fuselages surface, which is a result of the
fuselages manufacturing process. This will assist you in finding the center position, which
in turn will be used to locate the windscreen brace.
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 7 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Clean the windscreen mounting areas with thinners or alcohol removers to ensure they
are clean and will bond properly. Blow them with compressed air and a vacuum to
ensure they are totally clean.
Drill holes in the floor for the cables, flaps and the trim slot. Use the Dremel tool to cut
the holes and then sand smooth with a file and sandpaper. The same goes for the flap
handle area and also the throttle nutserts. The factory will already have these positions
marked for you in marker pen. Look at Appendix 2, 3 and 4 for hole diagrams with exact
dimensions.
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 8 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Dremel the holes and slots, use a vacuum cleaner to keep the dust under control when
cutting.
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 9 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Preparing the undercarriage
Drilling the main axle hole:
NOTE: The main axle hole most likely has already been drilled for you.
The main axle hole is drilled half way in from both sides to avoid drifting
The use of a reamer drill is recommended
The tighter the fit the better, therefore drill cautiously. The last thing you want to do is
drill a hole that is too big.
Placement of the main axle and endplates:
Place the endplates - be sure to align the plates correctly, as shown in the pictures below.
If aligned the wrong way, drilling the holes could cause perforation of the undercarriage's
upper edge. When the plates are aligned correctly, the holes are drilled further away
from the edge and will not cause perforation of the undercarriage.
Slide the axle through and fix the assembly with the washer and the non-machined nyloc
nut - apply Loctite 243 to the axle's threads before assembling the washer and nyloc nut
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 10 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Now we have to to drill the holes for the brake pins.
The goal is to drill a hole that is just deep enough, so that the pin, once placed, sticks out
exactly 1 cm from the brake assembly resting plate. This can be done by marking the
drill.
Insert the pins and tap them in with a hammer
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 11 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 12 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Placement of the brake assembly:
First check to see that the brake pad fits nicely into the brake assembly housing. It
should slide in and out of the housing smoothly, without being hindered or getting stuck.
If needed, lightly grind the brake pad's two alignment pegs with a file until the pad slides
in and out of the housing nicely. This is very important in order for the brakes to function
properly.
Slide the brake assembly on and ensure that it is properly seated on the resting plate. If
necessary, use a piece of pipe to tap it flush on the resting plate.
Note that there is a left and a right brake; they must be fitted so the hydraulic nipple is
pointing to the front of the aircraft on both sides of the plane.
Fit washer and clean brake – NOTE: FOR ALL VIRUS AND SIRUS MODELS WITH SERIES
NUMBER 277 AND GREATER, IT IS NOT NECESSARY TO PLACE A WASHER BETWEEN THE
BRAKE ASSEMBLY AND THE WHEEL. THESE MODELS HAVE AN ALTERED BRAKE
ASSEMBLY WITH A BIGGER FLANGE AND THUS DO NOT REQUIRE THE WASHER.
Brake assembly WITH washer
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 13 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Wheel placement:
Place wheel on the axle
Thoroughly grease the bearing and the wheel hub
Place the bearing and apply even more grease around the bearing afterwards
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 14 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Fit the dust cover on the axle after thoroughly greasing it.
Fit the nyloc nut - note there is no washer as the nut is especially machined to fit
Tighten the nut up so that the wheel still turns freely - do not over tighten the nut or the
wheel may bind
Wipe off excess grease
Fit the wheel spat spacer, but first apply Loctite 243 to the axle's threads
When tightening the spacer, be sure not to also tighten the locknut. Brace the locknut
while tightening the spacer as shown below.
Check one last time to ensure that the wheel turns freely and quietly.
Also grab the wheel with two hands and check to see that there is no free movement of
the wheel along the axis.
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 15 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Go to other side of axle and tighten the other locknut, torque setting 6 Newton meters.
Mark all nuts with red paint. Repeat for other side.
Check tire pressures at 32 psi or 2.2 atmospheres
Modification of the landing gear for the aircraft with a nose wheel:
Aircraft with a nose wheel have a different way to run the brake lines and it is necessary to
make modification to the tops of the landing gear legs. Normally the brake lines come from the
brakes and travel up the inside of the legs and enter into the cabin. If the aircraft has a nose
wheel, it is necessary to modify the exit hole so the line actually travels the normal route, goes
back into the landing gear leg and exits on the bottom where it then enters the cabin on the
front side of the leg.
Drill a hole at a 45 degree angle directly beside pre-drilled hole located on top of the
undercarriage's legs. Do the same for the other side. Check to make sure no sharp
edges remain.
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 16 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 17 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Fitting the undercarriage to the aircraft
For aircraft equipped with a nose wheel, the undercarriage is attached to the fuselage with bolts
and special washers.
These washers require a recessed hole to be drilled in the cockpit floor. Use an
appropriate drill bit.
It is important that the washer is seated properly; if you make the hole too big, it will
allow the undercarriage to move around excessively and if you make the recess too small,
the bolt and washer wont be seated properly. If by chance the holes are drilled too big,
be sure to fill them in with epoxy.
Note: for aircraft without a nose wheel there is no recess. There are just normal bolts
mounted with locknuts and a plate to hold the undercarriage in place.
Setup for aircraft without a nose wheel
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 18 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
Put a fair amount of epoxy around the top of the holes in the cockpit. This makes the
large locating washers sit perfectly in the holes.
Then put a light smear of grease around the bottom of the washer and around the bolt
shaft to stop the epoxy from sticking to the metal parts. It is important to have the
washers seated properly to avoid future damage to the structure
Cover the tops of the landing gear leg with silicone before mounting as shown below
Place undercarriage bolts into floor of fuselage and fit undercarriage leg. You'll need
someone to lift the front of the plane to do this, as its not so light.
Tighten the nylocs on the undercarriage to 5.5 Newton meters. Apply Loctite 243.
Wipe up any excess epoxy and grease. After 24 hours it is necessary to retighten the
bolts again to 5.5 Newton meters to allow for the epoxy to come out while it is curing.
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 19 of 267
K i t M a n u a l f o r P i p i s t r e l S i n u s a n d V i r u s A i r c r a f t
The last step is to prepare the fuselage for the brake lines. Position yourself under the
fuselage so that you're looking directly at the undercarriage and your legs are pointing
towards the engine.
Locate the center mark of the undercarriage's groove and drill two holes. Each hole
should be approximately 3 cm from the center mark.
Dremel the opening in the side of the aircraft for the brake lines to run from the pedals to
the wheels. The position is already marked in marker pen by the factory.
Be careful not to go to deep or you can go through the outer shell of the aircraft, then
clean up with a drill and sandpaper
http://www.pipistrel.si © Pipistrel Release March 2009 © Page 20 of 267
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267

Pipistrel Sinus Build Manual

Type
Build Manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI