Arkray Glucocard X-Meter User manual

User

Instruction

Manual

CAUTION:

Before using any product to test your blood sugar

(blood glucose), read all instructions and practice

the test. Do all quality control checks as directed and

consult with a diabetes healthcare professional. These

recommendations apply to all blood glucose monitoring

systems and are supported by the American Association

of Diabetes Educators, the American Diabetes

Association, the U.S. Food and Drug Administration, and

the Health Industry Manufacturers Association.

Introduction ...........................................5

Intended Use .......................................6

Understanding the GLUCOCARD™ 01-mini Blood Glucose Meter 7

Changing the Battery ...............................10

Changing Colored Faceplates. . . . . . . . . . . . . . . . . . . . . . . . 13

Meter Set-up .........................................15

Basic Rules ......................................17

Audible Beep ....................................18

Year . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Month/Day . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Hour/Minute .....................................22

Test Average Display ..............................23

Ending Set-up .........................................24

Performing a Control Solution Test. . . . . . . . . . . . . . . . . . . . . . . . 25

Troubleshooting Control Solution Test .................32

TABLE OF CONTENTS

3

Blood Glucose Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

The Lancing Device .......................................35

Getting a Drop of Blood ...................................38

Performing a Blood Glucose Test ............................40

Flagging Test Results .......................................44

Alternate Site Testing (AST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Understanding Test Results ....................................55

Recalling Results - Entering Memory Mode .......................60

Maintenance ...............................................64

Cleaning ................................................64

Storage and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Display Screen and Error Messages ..........................66

Product Information .........................................71

Product Speciﬁcations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Warnings, Precautions & Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Warranty ................................................75

4

Thank you for choosing the GLUCOCARD™ 01-mini Blood Glucose

Monitoring System. This system measures blood glucose in fresh

capillary whole blood. Results are shown as plasma values. This makes

it easy to compare the GLUCOCARD™ 01-mini Blood Glucose Meter

and lab results.

Please read this manual before using the system. If you have any

questions, call Customer Service at 800.566.8558 (24 hours a day,

7 days a week, USA and Canada only). Contact your healthcare

professional with questions if you are unable to reach Customer

Service.

INTRODUCTION

5

6

Intended Use

The GLUCOCARD™ 01-mini Blood Glucose Monitoring System is

intended for the quantitative measurement of glucose in fresh

capillary whole blood samples drawn from the ﬁngertips or palm.

Testing is done outside the body (In Vitro diagnostic use). It is indicated

for use at home (over the counter [OTC]) by persons with diabetes, or

in clinical settings by healthcare professionals, as an aid to monitor the

effectiveness of diabetes control.

The System Includes:

•Meter

•CarryingCase

•InterchangeableColoredFaceplates

•UserInstructionManual

•QuickReferenceGuide

•Self-testingLogbook

•LancingDeviceandLancets

Carrying Case

7

UNDERSTANDING THE GLUCOCARD™ 01-mini BLOOD GLUCOSE METER

Bottom

Test Strip

Port

Top

Display

Button(1)

Battery Cover

Strap Hole

Button(2)

Memory symbol:

Shows you a past result

in the memory.

Appears when you are

setting the date or time or reviewing

a past result.

Delete flag

Control test flag

Pre-meal flag

Post-meal flag

Battery symbol

Blood symbol:

Appears when the meter

is ready for testing.

Unit of Measurement

Thermometer symbol

Sound mute symbol

NOTE: Meters in the USA are programmed to show results in mg/dL.

Meters used outside the USA are programmed to show results in either

mg/dL or mmol/L. Results displayed in mmol/L will always have a decimal

point. Results displayed in mg/dL will never have a decimal point.

8

Explanation of the full display screen:

9

GLUCOCARD™ 01-SENSOR

These test strips need only 0.3 µL (microliter) of blood. Apply blood to the

sample application tip. The strip draws in the blood by capillary action.

The blood glucose reacts with the enzyme on the test strip. This produces

a current proportional to the blood glucose level. The meter detects the

current and converts it into a blood glucose reading.

Code No.

(F-2, 3 or 4)

Expiration date

F- 4

9

0018

F-4

Test Strip Bottle

Front Back

Test Strip

Sample

Application

Tip (Apply blood

to end of test strip.

Capillary draw will

pull blood to

reaction site).

Code No.

(F-2, 3 or 4) Contact Bars

Insert this

way into

meter

10

CAUTION: Replacing the battery will not delete meter settings or test

results stored in the meter unless you:

•Touchthemetalportiononmainunitwithyourngersoranymetal.

•Takeover1minutetoreplacebattery.

•Loadthebatteryincorrectly.

•Loadausedorweakbattery.

Changing the Battery

The GLUCOCARD™ 01-mini blood glucose meter comes with one lithium

battery CR2032 (or DL2032).

WARNING: Keep all batteries out of children’s reach. If a battery is

swallowed, consult a doctor immediately.

NOTE:

•Tosavebatterypower,themeterturnsitselfoff3–5minutesafterlastuse.

•Replacebatterieswhenlowbatterysymbolappears.Otherwise

inaccurate results could be obtained.

•Discardusedbatteriesasperlocalguidelines.

11

To replace battery:

1. Turn meter off.

2. Remove the battery cover on the back

of the meter.

3. Slide the battery to the right (a) and

remove it (b).

4. Load a new battery into the battery

cover. Place the “+” side upward.

CAUTION: Make sure the battery is loaded

in the proper position. Otherwise, the

preprogrammed times will be reset.

CAUTION: Do not touch the metal contacts

inside the battery compartment with your

ﬁnger or any metal.

a

b

12

5. Replace battery cover.

If the clock setting has been deleted, SET will appear on the screen.

If SET appears, set the time and date. If you do not set the time and

date, all subsequent results will be stored with a test date and time of

January 1, 2008, 12:00 a.m.

13

Changing the Colored Faceplates

The GLUCOCARD™ 01-mini comes with multiple interchangeable

colored faceplates. You can attach the color of your

choice.

1. Pressing on the dotted area shown on the right

with your thumb, slide the cover in the direction

of the arrow.

2. Turn your meter over. Hold the meter and pull

down the display cover until it comes off.

3. Remove the color faceplate from the

display cover.

Display

cover

4. Hook the end of the display cover into the hole

of your preferred color faceplate.

5. Fit one of the tabs on the display cover into the

corresponding slot on your meter.

6. Press forcefully on the dotted area shown on the

right to snap the display cover back into your

meter.

7. Slide the display cover back to its original

position. Make sure the display cover is

snapped closed.

Color

faceplate

7

6

14

Meter set-up allows you to adjust the audible beep volume and to set

time, date, and test averaging.

Before using the GLUCOCARD™ 01-mini blood glucose meter for the

ﬁrst time, set the time and date. Do not perform a blood glucose test

until you have set-up the meter.

METER SET-UP

Default Settings:

Audible Beep Volume High (3)

Average Off

15

16

Setup mode Audible Beep

See page 18.

Date and time

See page 20.

Test average display

See page 23.End

Press the button to

follow the black arrows.

To move from month

to day or from hour

to minute, press the

uppbutton. To change

the value, press the

lowbutton.

To go to SET:

1. Make sure

the meter

is off.

2. Hold down

both the

buttons for 5

seconds.

To change the

setting, press the

button.

NOTE

The meter turns itself off if no

buttons are pressed for 3 minutes.

Your changes will have been

stored. Review the settings for

confirmation in the SET mode.

Your new settings will be saved

when you reach the End screen.

and

To change the

setting, press the

button.

To turn off the

meter, press

button. To go

back to the bEP

screen, press

button.

Step 2: Press the and buttons at the

same time for 5 seconds. A beep sounds and the

meter turns on. Next, a second beep sounds and

“SET” shows on the screen.

17

Step 3: Use the button to change the set-up screen. When you press

the button, the set-up screen changes in the order shown in the

diagram to the left. Press the button to change a setting within a

set-up screen menu.

Note: If you need to go back to a setting, you must scroll through each

set-up option. You cannot go backwards in set-up mode.

In set-up mode, the meter will turn off automatically after 3 minutes of

non-use.

Basic rules for meter set-up:

Step 1: Turn off meter.

18

Setting the Audible Beep

If the audible beep is turned “on”, the beep will sound when:

•Youinsertateststripintothemeter.

•Youapplybloodorcontrolsolutiontoateststrip.

•Thetesthasendedandtheresultisdisplayed.

•Themeteristurnedon,butyoudonotuseitforseveralminutes. 

Meter will beep and automatically shut off.

•YougointoMemoryMode.

Make sure the meter is off. Press the and

buttons at the same time for 5 seconds.

A beep sounds and the meter turns on. Next, a

second beep sounds and “SET” shows on the

screen.

Press the button. The screen will

display “bEP” and the current beep setting.

19

Press the button to cycle through the volume levels:

“OFF” (no sound)

“on 1” (low)

“on 2”(middle)

“on 3” (high)

“OFF” (no sound) …, etc.

A beep sounds at the set volume

at each step. If “OFF” is set, the

“audible beep mute (Off)” symbol

lights up in the upper right of the

screen. After you select the beep

volume, press the button to

conﬁrm the setting. The screen

changes to the year set-up screen.

Beep

[4]

[1]

[2]

[3]

20

Setting the Year

In the year set-up screen, the last two digits of the

currently set year appear at the top of the screen.

“yEr” appears in the middle of the screen. The last

two digits of the currently set year appear at the

bottom of the screen and blink.

Press the button to change the last

two digits of the year to the correct year. After you

set the year, press the button to

conﬁrm the setting. The screen changes to the

month set-up screen.

(audible beep)

Page is loading ...

Arkray Glucocard X-Meter User manual

This manual is also suitable for

Arkray Glucocard X-Meter User manual

Related papers

Other documents