EverFocus EMV1200 HD User manual

User Manual

E

EM

MV

V1

12

20

00

0/

/8

80

00

0

D

DV

VR

R

EVERFOCUS ELECTRONICS CORPORATION

EMV1200/800 DVR

Instruction Manual

 2010 EverFocus Electronics Corp

www.everfocus.com

any means without written permission of the Everfocus Electronics Corporation.

Release Date: Jan. 2010

QuickTime is a registered trademark of the Apple Computer, Inc.

Windows is a registered trademark of the Microsoft Corporation.

Linksys is a registered trademark of the Linksys Corporation.

D-Link is a registered trademark of the D-Link Corporation.

DynDNS is a registered trademark of the DynDNS.org Corporation.

Other product and company names mentioned herein may be the trademarks of their respective owners.

ii

Safety Precautions

 Refer all work related to the installation of this product to qualified service personnel or system

installers.

 Do not block the ventilation openings or slots on the cover.

 Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the

power off immediately and contact qualified service personnel for service.

 Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or

covers. There are no user-serviceable parts inside. Contact qualified service personnel for

maintenance. Handle the appliance with care. Do not strike or shake, as this may damage the

appliance.

 Do not expose the appliance to water or moisture, nor try to operate it in wet areas. Do take immediate

action if the appliance becomes wet. Turn the power off and refer servicing to qualified service

personnel. Moisture may damage the appliance and also may cause electric shock.

 Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to clean

the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently.

 Do not overload outlets and extension cords as this may result in a risk of fire or electric shock.

 Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do

not use the appliance in an extreme environment where high temperature or high humidity exists. Use

the DVR at indoor type temperatures within -40℃~55℃ (-40F~131ºF). The input power source for

this device is 10V~36VDC.

 Read Instructions

All the safety and operating instructions should be read before the unit is operated.

 Retain Instructions

The safety and operating instructions should be retained for future reference.

 Heed Warnings

All warnings on the unit and in the operating instructions should be adhered to.

 Follow Instructions

All operating and use instructions should be followed.

 Cleaning

Unplug the unit from the outlet before cleaning. Do not use liquid cleaners, abrasive or aerosol

cleaners. Use a damp cloth for cleaning

iii

 Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

 Water and Moisture

Do not use this unit near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub,

in a wet basement, near a swimming pool, in an unprotected outdoor installation, or any area which is

classified as a wet location.

 Servicing

Do not attempt to service this unit by yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

 Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items

placed upon or against them, playing particular attention to cords and plugs, convenience receptacles,

and the point where they exit from the appliance.

 Object and Liquid Entry

Never push objects of any kind into this unit through openings as they may touch dangerous voltage

points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the

unit.

ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in

this case, the user ma

y

be ur

g

ed to take ade

q

uate measures.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one of the following measures :

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance

could void the users’ authority to operate this equipment.

iv

This Product is RoHS compliant.

WEEE

The information in this manual was current upon publication. The manufacturer reserves the right to revise and improve his products.

Therefore, all specifications are subject to change without prior notice. Manufacturer is not responsible for misprints or typographical

errors.

Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.

v

TABLE OF CONTENTS

1 PRODUCT OVERVIEW..................................................................................................... 1

1.1 FEATURES....................................................................................................................... 1

1.2 PACKAGE CONTENTS................................................................................................... 2

1.3 SPECIFICATIONS ........................................................................................................... 3

1.4 FRONT PANEL ................................................................................................................ 5

1.5 REAR PANEL................................................................................................................... 7

1.6 SYSTEM CONNECTION................................................................................................. 9

1.7 REAR PANEL CONNECTOR........................................................................................ 10

1.8 INSTALLATION OF EMV1200/800 ............................................................................. 12

1.9 VIDEO INPUTS/OUTPUTS INSTALLATION............................................................. 20

1.10 AUDIO INSTALLATION............................................................................................ 20

1.11 ALARM CONTACTS INSTALLATION .................................................................... 20

1.11.1 Alarm Input Contacts ............................................................................................................................21

1.11.2 Alarm Output Relay...............................................................................................................................21

1.12 USB-MOUSE INSTALLATION.......................................................................................... 21

1.13 NETWORK CONNECTION........................................................................................ 21

1.13.1 Direct PC Connection through Crossover Network Cable ...................................................................22

1.13.2 Network Connection through Patch Cable............................................................................................22

1.14 FINAL INSTALL PROCESS....................................................................................... 23

2 MOUSE OPERATION....................................................................................................... 24

2.1 GENERAL USB MOUSE OPERATION....................................................................... 24

2.1.1 How to select a channel.........................................................................................................................24

2.1.2 OSD Root Menu.....................................................................................................................................24

2.1.3 Field Input Options ...............................................................................................................................25

3 CONFIGURATION............................................................................................................ 26

3.1 CONFIGURATION OF DVR......................................................................................... 26

3.2 LOGIN............................................................................................................................. 26

3.3 ON SCREEN CONFIGURATION MENU ................................................................................ 27

3.4 SEARCH ......................................................................................................................... 28

3.4.1 Time Search...........................................................................................................................................29

3.4.2 G Sensor Search....................................................................................................................................30

3.4.3 GPS Speed Search.................................................................................................................................31

3.4.4 Event Search..........................................................................................................................................33

3.5 ARCHIVE (USB)............................................................................................................ 35

3.6 ZOOM ............................................................................................................................... 36

4 DVR CONFIGURATION.................................................................................................. 37

4.1 CONFIGURATION MENU.................................................................................................... 37

4.2 CAMERA SETTING ...................................................................................................... 39

vi

4.2.1 Normal...................................................................................................................................................39

4.2.2 Video Loss.............................................................................................................................................41

4.2.3 Alarm.....................................................................................................................................................43

4.3 RECORD SETTING ....................................................................................................... 44

4.3.1 Record ...................................................................................................................................................44

4.4 ALARM/GPS .................................................................................................................. 45

4.4.1 Alarm-Alarm Settings............................................................................................................................45

4.4.2 Alarm-Event Settings.............................................................................................................................47

4.4.3 Alarm – Video Loss...............................................................................................................................56

4.4.4 Alarm-G-Sensor Settings.......................................................................................................................58

4.4.5 Alarm-GPS Speed..................................................................................................................................59

4.4.6 Alarm-GPS Event Action.......................................................................................................................60

4.4.7 Alarm-GPS Fencing..............................................................................................................................61

4.5 DATE/TIME SETTING ........................................................................................................ 62

4.5.1 Date/Time Settings ................................................................................................................................62

4.5.2 Daylight Saving.....................................................................................................................................63

4.6 DISPLAY ........................................................................................................................... 64

4.6.1 Title .......................................................................................................................................................64

4.6.2 Monitor On Screen Display...................................................................................................................64

4.6.3 Layout....................................................................................................................................................66

4.6.4 Sequence................................................................................................................................................67

4.7 NETWORK SETTING.................................................................................................... 68

4.7.1 LAN Settings..........................................................................................................................................68

4.7.2 Wireless Settings....................................................................................................................................71

4.7.3 Mobile Connection Settings...................................................................................................................72

4.7.4 Email Settings........................................................................................................................................73

4.7.5 DDNS Settings.......................................................................................................................................74

4.7.6 Alarm Server Settings............................................................................................................................76

4.7.7 Meta Server Settings..............................................................................................................................77

4.7.8 Network Test..........................................................................................................................................78

4.7.9 Remote/Mobile ......................................................................................................................................79

4.8 SYSTEM ......................................................................................................................... 80

4.8.1 User.......................................................................................................................................................80

4.8.2 I/O Control............................................................................................................................................83

4.8.3 DISK......................................................................................................................................................85

4.8.4 LOG.......................................................................................................................................................86

4.8.5 SETTINGS.............................................................................................................................................88

4.8.6 SERVICE...............................................................................................................................................89

4.9 INFORMATION............................................................................................................. 90

5 NETWORKING OVERVIEW.......................................................................................... 91

5.1 INTRODUCTION TO TCP/IP............................................................................................... 91

5.2 SUBNET MASKS................................................................................................................ 91

5.3 GATEWAY ADDRESS......................................................................................................... 91

5.4 VIRTUAL PORTS................................................................................................................ 92

5.5 PRE-INSTALLATION .......................................................................................................... 92

5.6 WHAT IS YOUR NETWORK SETUP?.................................................................................... 93

5.7 SIMPLE ONE TO ONE CONNECTION................................................................................... 94

5.8 DIRECT HIGH SPEED MODEM CONNECTION ..................................................................... 99

vii

5.9 ROUTER OR LAN CONNECTION...................................................................................... 101

6 REMOTE OPERATION FROM BROWSER.................................................................... 104

6.1 CONNECTING TO EMV1200/800.............................................................................. 104

6.2 BROWSER SECURITY SETTING .................................................................................. 105

6.2.1 Installing ActiveX controls..................................................................................................................105

6.2.2 Enabling ActiveX Controls..................................................................................................................108

6.3 GREMOTE LIVE VIEW.............................................................................................. 111

6.4 REMOTE PLAYBACK................................................................................................ 113

7 EVERFOCUS DDNS SETUP.......................................................................................... 114

8 LINKSYS & D-LINK PORT FORWARDING ............................................................. 116

8.1 TYPICAL LINKSYS PORT FORWARDING............................................................. 116

8.2 TYPICAL D-LINK PORT FORWARDING ................................................................ 118

9 TROUBLESHOOTING................................................................................................... 121

APPENDIX A: TIMING OF ALARM MODES.................................................................... 123

APPENDIX B: EXPRESS SETUP RECORDING VALUE SELECTION RULES .......... 126

APPENDIX C: REMOTE CONTROL................................................................................... 128

1

1 PRODUCT OVERVIEW

Full featured video surveillance on the move: the EverFocus EMV1200 / 800 digital video recorder, with

H.264 compression technology for enhanced recording capacity and improved network image transmission

speed with high image quality, delivers real-time video and audio recoding on all 12 / 8 channels along with

comprehensive features including hot swap hard drive, embedded 3-axis g-sensor, GPS receiver interface,

802.11 b/g WiFi, individual camera power outputs, remote control capability and shock/vibration resistant

locking Molex connectors make this DVR the best choice for your portable and mobile recording

applications. The DVR provides multiple interfaces including 3 USB ports, RS-485, RS-232, GPS port,

wired and WiFi Ethernet, IR remote control, 12 / 8 alarm inputs and 2 alarm outputs. Video and audio

outputs are provided at both front and rear panels for ease of installation and maintenance, plus the new

easy to read graphical user interface is specially designed for use with portable small-screen monitors. The

power supply in the EMV1200 / 800 provides surge protection, voltage regulation, and programmable delay

power on/off for the DVR and the system cameras. The EMV1200 / 800 can be equipped with an optional

explosion-proof ‘Explosion-proof storage’ to retain the last minute of recorded video for

evidence/investigation.

1.1 FEATURES

 12 / 8 Channels of video and audio recording

 Recording Rate :

EMV1200 : 120fps @ D1 resolution / 240fps @ 2CIF / 360fps @ CIF resolution (duplex)

EMV800 : 240fps @ D1 / 2CIF / CIF resolution

(with global settings; record rate, resolution and quality can be set independently per-camera up to

the maximum of 360 / 240 CIF-equivalent FPS)

 H.264 compression format for efficient disk and network utilization

 Front and rear panel video/audio outputs for easy connection and configuration

 Special Graphical User Interface design for use with mobile small-sized monitors

 Molex connectors for shock & vibration resistance; interface cables to BNC, RCA and power jacks

supplied

 Alarm Inputs & Outputs : 12 / 8 & 2 (alarm outputs are form “C”)

 Embedded 3-axis g-sensor function with separate programmable alarm levels for X/Y and Z axis

 Removable video storage hard disk; easy playback on PC (using EPR110 purchased separately)

 Supports single 3.5” SATA hard disk standard (up to 2TB), 2.5” SATA hard disk standard (up to 1TB)

 Supports multiple interfaces: 3xUSB , RS-485, RS-232, GPS port, wired Ethernet, IR Remote Control

 Built in wireless 802.11 b/g with diversity antennas

 Provides camera power for 8 cameras; interface cables to power jacks supplied

Chapter

1

2

 Optional External EDGE/GPRS/CDMA/WI-FI Modules for cellular/specialized wireless Transmission

 GPS function tracks speed and geographic limits (optional external GPS receiver)

 Explosion-proof ‘Explosion-proof storage’ interface (option)

 Power Supply : 10V~36VDC with Surge Protection, Voltage Regulator, programmable Delay on/off

 Temperature : -40ºC ~ 55ºC (Operating), -40ºC ~ 85ºC (Non-Operating)

1.2 PACKAGE CONTENTS

- Digital Video Recorder x1

- HDD Tray x 1

- HDD Fixing Bracket x 1 set

- Screws x 1 pack

- Antenna x 1 set

- IR Remote Control x 1

- Battery x 2

- Camera Power cable x 3

- Video & Audio cable x 3

- Alarm cable x 1

- Alarm Output cable x 1

- RS232/RS485 cable x 1

- GPS cable x 1

- GPS PS2 to MOLEX converter cable x 1

- Camera power converter cable x 3

- DVR power cord x 1

3

1.3 SPECIFICATIONS

EMV1200 / 800 – 12 / 8 Channel Mobile DVR

Video Format NTSC/PAL (auto detected by system)

Operating System Embedded Linux with special small monitor friendly GUI

Video Input 12 / 8 channels (vibration resistant locking Molex connectors –

Interface cables to BNC-F supplied: 3X / 2X groups of 4 cameras

each)

Video Output Main monitor: 1 composite BNC rear panel / 1 front panel RCA

output

Call monitor: 1 composite BNC rear panel

Video Compression H.264

Video Display Full, 4/9/12, Sequence

Recording Resolutions

(set independently per

camera) NTSC: 720x480/720x240/360x240

PAL: 704x576/704x288/352x288

Audio Inputs 12 / 8 line in (vibration resistant locking Molex connectors -

Interface cables to RCA-F supplied:3X / 2X groups of 4 cameras

each)

Audio Outputs 1 front panel RCA line out, 1 rear panel RCA line out

Alarm Inputs 12 / 8 alarm inputs (vibration resistant locking Molex connectors -

Interface cables supplied)

Alarm Outputs 2 alarm outputs (form “C”; contacts rated at 30V AC/DC @ 1

amp – interface cables supplied)

Storage 3.5" HDD x 1 (up to 2TB ) or 2.5" HDD x 1 (up to 1TB )

Recording Rate

12CH

NTSC: D1 120fps, 2CIF 240fps & CIF 480fps(duplex) if set

globally

PAL: D1 100fps, 2CIF 200fps & CIF 400fps(duplex) if set globally

8CH

NTSC: D1/2CIF/CIF 240fps if set globally

PAL: D1/2CIF/CIF 200fps if set globally

Per camera resolutions and record rates can be set individually

per camera through the OSD menus up to the maximum record

capacity of 480 NTSC (400 PAL) / 960 NTSC (800 PAL) CIF

equivalent FPS

Recording Mode Continuous recording, event recording, continuous + event

recording

(Rate and resolution in each mode set independently per camera)

Record Quality Adjustable in five levels per camera per Record Mode

Pre Alarm Recording Optional; 5 second interval

Playback Rate

12CH

NTSC: D1 120fps, 2CIF 240fps & CIF 480fps(duplex)

PAL: D1 100fps, 2CIF 200fps & CIF 400fps(duplex)

8CH

NTSC: D1/2CIF/CIF 240fps

PAL: D1/2CIF/CIF 200fps

4

Camera resolutions and record rates can be set individually per

camera through OSD menus up to the maximum total record

capacity of 480 (400)/ 960(800) CIF FPS

Playback Search Time/date, event search

Video Loss Detection Yes

Event Alarm Fan failure, hard disk temperature, hard disk failure, hard disk full,

hard disk removed, power loss (after power is restored), network

loss, GPS loss, GPS speed, GPS fencing, G sensor limits

Email alert Multiple email notifications in response to alarms and events.

(Requires real time network connectivity though cellular or WiFi

service).

G Sensor Embedded 3-axis G Sensor; data recorded; alarm if separate user

limits for X/Y or Z axis exceeded

GPS Function Optional External GPS Sensor for speed and geographic limit

alarms (rectangular or circular fencing)

Configuration Method On screen menu with ‘portable monitor friendly’ graphical user

interface

Control/Setup IR remote control, USB mouse, network I/F

Real time clock Can be synchronized to GPS/NTP time source; flexible DST

settings

Watchdog Function Reboots DVR automatically if required

Networking RJ45 socket, 10/100Mbps; 802.11b/g WiFi, diversity antennas

TCP-IP/DHCP/PPPoE/DDNS/SMTP/SSL/POP3/HTTP/NTP

System Warnings System fail LED : HDD full, HDD/Sys Temp, Fan fail,

HDD fail LED : HDD power off, HDD failure

File Export USB 2.0 interface

Interfaces RS-232 x 2, RS-485, USB x 3, GPS port

Explosion-proof storage 4GB device (option)

Power Source

10V~36VDC (Built in surge protection, voltage regulation,

programmable Delay On/Off relative to ignition or other switched

voltage)

With 4.8 / 3 amps cameras

Camera Power Outputs

Total current 4.8 / 3 amps @ 12VDC (vibration resistant locking

Molex connectors – interface cable provided to coaxial power

plugs: 3 X groups of 4 cameras); 1.2A for camera 1~4 and 1.8A

for camera 5~12

Dimensions (W x D x H) DVR alone : 210 x 260 x 70mm / 8.27" x 10.22" x 2.76"

DVR in mount with antennas : 312 x 298 x 164mm / 12.29" x

11.75" x 6.47"

Weight DVR without mount 3.2kg / 7.05 lbs.

DVR with mount 3.65kg / 8.05 lbs

Operating Temp. Working Temperature: -40℃~55℃; -40F~131ºF

Storage Temperature: -40℃~85℃; -40F~185ºF

5

1.4 FRONT PANEL

Your primary interaction with your new DVR will be through the Front Panel buttons and their

corresponding buttons on the included IR Remote Control. Take a moment to learn where the keys are as

the remainder of the manual will refer to them often.

Figure 1-1 Front Panel

1) USB 2.0: For connecting USB-Flash-Drive to copy/archive video or for firmware upgrades.

2) Audio Out: Connect to the line level input of an audio amplifier (same output as the audio out at

rear panel, no conflict between these 2 outputs, they both can be connected

simultaneously).

3) Main Monitor Out: Main monitor for live and playback display and on-screen display. (same output

as the main monitor out at rear panel, no conflict between these 2 outputs, they both

can be connected simultaneously).

6

4) ETHERNET: RJ-45 network connection 10/100Mbps Ethernet. There are two LEDs on the LAN jack;

Green LED means network is connected, amber LED flickers when data is being

exchanged.

5) System Status LEDs: Indicators system status.

System fail LED: HDD full, HDD/System Temperature, Fan fail

HDD fail LED: HDD power off, HDD failure

Copy: This LED ON indicates system is archiving data.

LAN: This LED ON indicates Network active. Network LED turns on depending on the network type

(LAN, Wireless or Mobile) set in Network setting.

Record: This LED ON indicates Record active.

Power: This LED ON indicates Power on.

7

1.5 REAR PANEL

During initial setup you will be connecting your DVR to multiple input and output devices. This is done

through the rear panel.

Figure 1-2 Rear Panel

○

1 Main Monitor Out: Main monitor for live and playback display and on-screen display.(same output as

the main monitor out at front panel, no conflict between these 2 outputs, they both can be

connected simultaneously)

○

2 Audio Out: Connect to the line level input of an audio amplifier. (same output as the audio out at front

panel, no conflict between these 2 outputs, they both can be connected simultaneously)

8

○

3 Alarm Input: Connect up to 12/8 alarm inputs, selectable between N.O./N.C. contacts.

○

4 Alarm Output: N.C or N.O type alarm out (form “C”).

○

5 RS232 socket: Connect this connector to RS232/RS485 compatible device.

○

6 GPS Data Input: Connect this connector to GPS receiver via GPS cable.

○

7 USB port: USB port recommended for connecting the USB mouse.

○

8 Power Input/Ignition Control In/Switched power out: 4 pins are reserved for power input; connect to

10V~36VDC power source. 1pin is for ignition control; connect to the other vehicle devices to avoid

excess power consumption at ignition. 1 pin is reserved for switched power out. The power source

used for this additional power output is 600 mA x 12VDC.

○

9 Video & Audio Inputs (12/8): Connect camera’s video output or other composite video source to the

video input connection.

Connect line level output of an audio preamplifier to the audio input connection corresponding to the

appropriate camera.

○

10 Camera Power Outputs (12/8): EMV1200/800 can provide power source to cameras, connect camera

power to this output by using the camera power cable. For EMV800, the power source used is 450mA

x 12VDC. For EMV1200, the power source used for the first 4 CH is 300mA x 12VDC and 450mA x

12VDC for the rest.

○

11 Serial Port: Reserved port.

○

12 Control Port: Reserved port.

○

13 Call Monitor Out: This connector is used for the call monitor. This monitor can only display a full screen

picture.

○

14 802.11 b / g WiFi: Connection of the antenna.

9

1.6 SYSTEM CONNECTION

Please refer to the following diagrams for the system connections.

Note: Monitor and Camera must be purchased separately.

10

1.7 REAR PANEL CONNECTOR

RS232/RS485

TX RX GND

485+ 485- GND

ALARM IN

ALM IN1 ALM IN2 GND ALM IN3 ALM IN4 GND ALM IN5 ALM IN6 GND

ALM IN7 ALM IN8 GND ALM IN9 ALM IN10 GND ALM IN11 ALM IN12 GND

VIDEO/AUDIO IN1

VID IN1 VID IN2 VID IN3 VID IN4 AUD IN1 AUD IN2 AUD IN3 AUD IN4

GND GND GND GND GND GND GND GND

VIDEO/AUDIO IN1

VID IN5 VID IN6 VID IN7 VID IN8 AUD IN5 AUD IN6 AUD IN7 AUD IN8

GND GND GND GND GND GND GND GND

VIDEO/AUDIO IN1

VID IN9 VID IN10 VID IN11 VID IN12 AUD IN9 AUD IN10 AUD IN11 AUD IN12

GND GND GND GND GND GND GND GND

ALARM

OUT

NC2 COM2 NO2

NC1 COM1 NO1

11

POWER

IGN 12V 12V

OUT GND GND

CAM POWER1

12V OUT 12V OUT 12V OUT 12V OUT

GND GND GND GND

GPS

GND GPS_TX

GPS_RX +5V

CAM POWER2

12V OUT 12V OUT 12V OUT 12V OUT

GND GND GND GND

CAM POWER3

12V OUT 12V OUT 12V OUT 12V OUT

GND GND GND GND

12

1.8 INSTALLATION OF EMV1200/800

 The DVR can be mounted horizontally (suspend or support mounted).

 Show all the possible ways to mount the DVR.

Use the two Z-brackets supplied to mount it in any ways shown.

Support

Suspend

Interface

Support

Sus

p

end

ED

S

R4

0

EDSR400M

Support

Page is loading ...

EverFocus EMV1200 HD, EMV800 User manual

Related papers

Other documents