Beghelli Fortezza™ Plus Installation guide

Brand: Beghelli

Model: Fortezza™ Plus

Type: Installation guide

926000318 02/10/14

BEGHELLI USA 3250 CORPORATE WAY - MIRAMAR, FL 33025 • P: 800.726.4316 • P: 954.442.6600 • F: 954.442.6677

INSTRUCTIONS

Fortezza™ Plus (FTZ)

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS

2. Disconnect power before performing work on electrical equipment.

3. Use caution when servicing batteries.

4. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to

tampering.

5. The use of accessory equipment not recommended by Beghelli USA Inc., may cause an unsafe condition, and

will void the unit’s warranty.

6. Do not use this equipment for other than its intended purpose.

7. Servicing of this equipment should be performed by qualiﬁed service personnel.

8. SAVE THESE INSTRUCTIONS!

Chassis GND LED Board

AC ONLY SIGN

Chassis GND

GREEN Ground

BLACK 120VAC

RED 120-277VAC or ORANGE 200-277VAC

WHITE Neutral

LED Board

AC & UNIVERSAL DC SIGN

YELLOW Positive 6 to 24VDC

PURPLE Negative

Emergency Supply

FROM Battery Pack

SELF-POWERED SIGN

Chassis GND

24 hours

Unswitched Supply

GREEN Ground

BLACK 120-277VAC

WHITE Neutral

LED Board

DUAL UNIVERSAL AC SIGN

From Generator OR

Emergency Supply

BROWN 120 to 277VAC

BLUE Neutral

NOTE: Cap unused AC Wire!

24 hours

Unswitched Supply

GREEN Ground

BLACK 120VAC

RED 120-277VAC or ORANGE 200-277VAC

WHITE Neutral

24 hours

Unswitched Supply

Chassis GND LED Board

NOTE: Cap unused AC Wire!

GREEN Ground

BLACK 120VAC

RED 277VAC or ORANGE 120-277VAC

WHITE Neutral

24 hours

Unswitched Supply

Ni-Cd

Battery

CEILING/END MOUNT INSTALLATION

WALL MOUNT INSTALLATION:

1. Remove torx screws (9) to release clear cover (1). There are 4 O-rings (10) inserted to the clear cover screw holes.

Release the stencil (2) from the clear cover (1). Knockout to remove the chevron as necessary from the stencil.

Peel o backing paper from the tape on the back of the stencil and carefully position and stick the colored ﬁbre to the

stencil.

2. To install canopy kit, knockout on the top (for ceiling mount) or the knockout on the side (for end mount). Position

canopy gasket and the canopy (14). Install the cap screws and the washers. Attach canopy nuts and then tighten.

Install the liquid tight bushing (12), feed the lead wired through the bushing and tighten to complete the liquid tight

seal. Install the canopy mounting base (15) to the octagon box (11) (not supplied). Connect wires per diagram

provided. Caution! Failure to insulate unused wire may result in a shock hazard or unsafe condition as well as

equipment failure. The mounting base can be rotated for the desired mounting angle. Install the canopy (14) to the

mounting base (15) with the supplied screws.

3. Note: When installing the cover, be sure to align the light pipe (5) and LED indicator.

4. Apply power.

SELF-POWERED:

1. For models FTZ-SP, plug the battery into the circuit board per (wiring diagram) self-powered sign.

MAINTENANCE

1. Clean face(s) on a regular basis.

NOTE: The servicing of any parts should be performed by qualiﬁed service personnel only. The use of replacement

parts not furnished by Beghelli Canada Inc., may cause equipment failure and will void the warranty.

WIRING DIAGRAM

1. Remove torx screws (9) to release clear cover (1). There are 4 O-rings (10) inserted to the clear cover screw holes.

Release the stencil (2) from the clear face cover (1). Knockout to remove the chevron as necessary from the stencil.

Peel o backing paper from the tape on the back of the stencil (2) and carefully position and stick the colored ﬁbre to

the stencil.

2. Remove the back plate (16) knockouts using applicable knockout holes. Install the liquid tight bushing into the large

center knockout with the lock nut (12). Feed the lead wires through the bushing, tighten to complete the liquid tight

seal and install the wall gasket (18) then secure the back plate and housing to the wall. Connect wire per wiring

diagram provided. Caution! Failure to insulate unused wire may result in a shock hazard or unsafe condition as

well as equipment failure.

3. Replace faceplate, clear cover and torx screws. Note: When installing the cover, be sure to align the light pipe (5) and

LED indicator.

4. Apply power.

926000318 02/10/14

BEGHELLI USA 3250 CORPORATE WAY - MIRAMAR, FL 33025 • P: 800.726.4316 • P: 954.442.6600 • F: 954.442.6677

I cahnged the contact info, the technical info seems pretty universal is there anything else you see that I need to change?

926000318 02/10/14

BEGHELLI USA 3250 CORPORATE WAY - MIRAMAR, FL 33025 • P: 800.726.4316 • P: 954.442.6600 • F: 954.442.6677

Parts List

DESCRIPTIONITEM

CLEAR COVER

STENCIL2

FRAME

FIBER4

LIGHTPIPE5

LED BOARD6

TEST SWITCH7

CEILING MOUNT GASKET8

TAMPER PROOF SCREWS9

O-RING10

OCTAGON BOX(SUPPI

I cahnged the contact info, the technical info seems pretty universal is there anything else you see that I need to change?

ED BT OTHERS)

BUSHING12

CANOPY GASKET13

CANOPY14

CANOPY MOUNTING BASE

BACK PLATE16

CAP SCREWS

WALL MOUNT GASKET18

OVAL HEAD SCREWS19

BATTERY BOX20

PART #

Figure 1

PARTS L IST

1. Clear Cover

2. Stencil

3. Frame

4. Fiber

5. Lightpipe

6. LED board

7. Test switch

8. Ceiling mount gasket

9. Tamper proof screws

10. O-ring

11. Octagon box (not supplied)

12. Bushing

13. Canopy Gasket

14. Canopy

15. Canopy mounting base

16. Back plate

17. Cap screws

18. Wall mount gasket

19. Oval head screws

20. Battery box

Beghelli Fortezza™ Plus Installation guide

Beghelli Fortezza™ Plus Installation guide

Beghelli Fortezza™ Plus Installation guide

Related papers

Other documents