1
Installation Instructions
TOOLS NEEDED: HARDWARE NEEDED:
Step -by-Step Installation Sequence
anovafurnishings.com
800.231.1327
Some products may require assembly before or during installation; please consult the assembly instructions if applicable.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a 3,000 psi
minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
1. Place the product in the desired location.
Mark the location of the holes with a pencil. To
verify the alignment of your anchor markings,
reference the foot mount sheet at the back of
these instructions.
RLA30 - Vibe Bike Rack
Wrench / Socket Set
Mason Drill Bit Set
Hammer Drill
Safety Glasses
Pencil
Wire Brush
LevelHammer
SS or Rubber Washers
90107A127 OR 90130A050
OPTIONAL
B
A
3/8" x 5" 18-8
Stainless Steel Stud Anchors
92188A203
Installation Instructions
2
RLA30 - Vibe Bike Rack
2. It is recommended that you start holes in
sequential order from the smaller to the larger
drill bits to avoid oversized holes or holes drilled
to deep.
3. Evacuate debris from the mounting holes using
compressed air and a steel wire brush.
4. Locate an anchor and adjust the nut so it is ush
to the top of the anchor to protect the threads
from being damaged, and insert into the hole.
5. Use the hammer to x the anchor into the
drilled hole by giving it several hammer blows.
6. Repeat steps 2-5 until all anchors are installed.
7. Align the mounting holes of the product over
the top of the anchors
8. Care should be taken to avoid rubbing the
powder coating o the foot. Mount the product
to the anchor using fasteners (B) and washers
(C). Leave hardware nger tight until all have
been installed.
9. Verify the product is level and aligned properly
and tighten all hardware.
Installation Instructions
3
RLA30 - Vibe Bike Rack
• Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,
missing, or broken hardware, and general instability
• Furniture that is damaged or appears to be unstable must be removed from service and repaired or replaced
• Repairs must be made using only factory authorized parts and methods.
WARNING
• Do not drag the assembled unit across any surface.
• This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove
surface dirt. Do not clean with a solvent or petroleum based products.
CARE AND
MAINTENANCE
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
FOOT MOUNT(S)
07/10/2023 Copyright 2023 Anova ® Manufactured in the U.S.
2.50
20.36
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
001
RLA30
SHEET 1 OF 1
1:2
7/5/2023
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
7/5/2023
/
