© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
10’
VK-1964 - 10’ x 10’ Display
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View
© 2023
Order #XXXXX General Information
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
© 2023
Order #XXXXX
Straight Connection
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Straight Connector
Straight Connector
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
CEI110 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
CEI110 Frame Assembly
© 2023
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab. Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation
© 2023
Case 1 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Graphics
Setup Hardware
Top View of Each Level
Level 1
Wings
4 5 4A 5A 3A,3 8 8A 2,2A
Level 2 Level 3
iPad Holders
Case Packing
© 2023
Case 2 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
7A
10A 10/11
Counter Top
Base
Plates
6A 6 7
Canopy
Pieces
Level 2 Level 3
Case Packing
© 2023
Case 3 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
SHELF SUPPORTS
Door
6, 6A, 7, 7A
Side
Panel
Assembly
Side
Panel
Assembly
Shelf
Counter Top
Infill
Top View of Each Level
Level 1 Level 2 Level 3 Level 4 Level 5
Case Packing
© 2023
Step 1 of 5
Order #XXXXX
Locked layer contains
placeholder marks.
4
1
5
8
8A
1
4A
5A
3
3A
6A
7A
2
2A
6
7
Power
Break
Completed Backwall Assembly
Power
Break
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
Item
1
2/2A
3/3A
4/4A
5/5A
6/6A
7/7A
8/8A
Qty.
2
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Description
Base Plate
42”w S40 Vertical Extrusion
42”h S40 Vertical Extrusion
42”h CEI110 Horizontal Extrusion
42”h CEI110 Horizontal Extrusion
42“h CEI110 Vertical Extrusion
42“h CEI110 Vertical Extrusion
40.1767“h Z45 Vertical Extrusion
Steps:
1) Attach Base Plates [1] to Vertical [2] & [3], using bolts.
3) Assemble CEI-110 Extrusions together, with Verticals [8,8A] between.
See General Information page CEI-110 Frames Assembly for details.
4) Connect Verticals [2,2A] and [3,3A] together then attach to each side
of assembled CEI-110 frame. See CEI-110 to S40 Connection detail.
5) Connect lighting power cords and attach transformers.
See Light to Light Connections & Light to Transformer details.
6) Apply SEG graphic and blocker to front & back of assembled frame.
See SEG Graphic Installation detail.
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
Light to Light Attachment
Light to Tranformer Attachment
CEI-110 to S40 Connection
V4 Connector
CEI-110
S40
Slide V4 Connector into groove of S40. Tighten set
screw with tool to secure V4 Connectorin place at
correct elevation (may be already in place on the
Verticals [2,2A,3,3A]). Insert Socket-Head Bolt through
hole of CEI-110 into matching threaded hole of V4
connecator. Tighten Socket-Head Bolt with tool to
secure in place.
Socket-Head
Bolt
Backwall Assembly
© 2023
Step 2 of 5
Order #XXXXX
Using Your Setup Instructions
The Aero Setup Instructions are created specifically for your configuration. The instructions include an
exploded view of the frame which is sequentially labeled. We encourage you to review the instructions
before attempting to assemble your exhibit.
Connections are kept very simple; no tools required. Everything assembles with push-button connectors.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Push-Button
Push-Button
66
6
6
Numbered Label
Connections are made by holding the button down and
sliding the red tube into opposing tube until button locks
into the hole of the opposing tube. To disassemble, push button
and pull or twist extrusions apart.
Locked layer contains
placeholder marks.
Steps:
1) Connect canopy pieces together as shown.
2) Apply pillow case graphic to assembled canopy.
AA
BB
D
D
CC
Push-Button
Push button then rotate
for packing purposes
E
F
E
FG
H
G
H
Canopy Assembly
© 2023
Step 3 of 5
Order #XXXXX
Locked layer contains
placeholder marks.
Completed Assembly
10
10A
2
Canopy
11
Screw
Note: Curved Extrusion
[10] and Horizontal [11]
stay assembled for
shipping and packing.
*
Item
10
10A
11
11A
Description
30.2” Curved Extrusion
Support Leg
12.184”w Horizontal Extrusion
Flange Plate
Qty.
1
1
1
1
Steps:
1) Connect assembled Extrusions [10/11] and Shelf to Vertical [2].
2) Connect Support Leg [10A] to Curved Extrusion [10].
3) Attach Flange Plates [11A] to tops of Curved Extrusions [10], using screws.
4) Attach Counter Tops to [11,11A]. See Counter Top Attachment detail.
5) Attach Wings to A10 clamps. See Wing Attachment detail.
6) Place Canopy on posts at top of assembled frame.
Counter Top Attachment
*Insert Screws, located on underside
of Counter Top, into holes on Flange
Plate then secure with Wing Nuts.
Wing Nut
Fixed
Screws
Flange
Plate
10
11
Counter Top
Slide A10 clamp into
groove of Extrusion.
When desired location
is found, tighten
Set Screw to secure.
Set
Screw
A10
Tighten Black Plastic
Set Screw to secure
Wing in place.
Wing Attachment
Keep A10 clamps
attached to Verticals
Black
Plastic
Set Screw
Shelf
11A
Backwall Attachments
© 2023
Step 4 of 5
Order #XXXXX
Locked layer contains
placeholder marks.
Infill
Infill
Infill
1
56
5
Door
Shelf
Counter
iPad Stand
7
2
3
5A 6A
5A
7A
4
HingeHinge
Completed Assembly
Item
1
2
3
4
5/5A
6/6A
7/7A
Qty.
1
1
1
1
2/2
1/1
1/1
Description
37.5”h Vertical Extrusion
37.5”h Vertical Extrusion
37.5”h Vertical Extrusion
37.5”h Vertical Extrusion
13.25”w Horizontal Extrusion
22.5”w Horizontal Extrusion
22.5”w Horizontal Extrusion
Steps:
1) Connect lower horizotnals [5, 6 & 7] between verticals.
2) Place infills between verticals where indicated.
3) Attach door using hinges.
See Door Attachment detail.
4) Insall shelf supports to inside of counter, using velcro.
4) Lower shelf down on to the top of the
shelf supports and set in place.
5) Attach upper horizontals [5A, 6A & 7A] between verticals.
6) Place counter on top of assembly and lock in place.
See Counter Top Attachment detail
7) Attach iPad stand to counter using bolt under counter.
See Swivel iPad Clamshell Attachment detail.
BACK SIDE
BACK SIDE
BACK SIDE
FRONT SIDE
Hex
Nuts
Clamshell rotates
between portrait
and landscape
viewing modes.
Swivel
Mounting
Plate
Swivel iPad Clamshell
Attachment
Bolt iPad clamshell to mounting
plate with hex nuts.
Cord
Access
iPad
Lock
Lock
*
*
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
**
Shelf Supports
Shelf Supports
Shelf Supports
Shelf Supports
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
Reception Counter Assembly
© 2023
Step 5 of 5
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Attach mount plate to post, using set screw.
NOTE: Mount plate must rotate to left and right before installing clamshell.
2) Attach post assembly to counter top, using bolt from under counter top.
3) Attach clamshell to mount plate, using hex nuts.
4) Insert iPad in clamshell, then route cords. See Cord Management for iPad detail.
Counter
Top
Clamshell
Foam Lining
Removed
Home Button Shield
Optional Cover for Home Button
1) Remove foam lining from inside bottom of
clamshell.
2) Attach Home Button Shield with double-sided
tape to inside of clamshell, keeping top of
shield flush with clamshell opening.
NOTE: This is a permanent fix and can’t be
easily removed.
Rotate clamshell
to turn iPad from portrait
to landscape orientation.
Hex
Nuts
Completed Assembly
Mount
Plate
Post Rotates
Set
Screw
Post
to power
Cord Management for iPad
Attach iPad cord to supplied USB extension
cord. Feed USB cord through top hole of
post, then out bottom hole of post.
Connect to power.
Cord
Access
iPad
Lock Lock
Bolt
MOD-1329 Rotating iPad Mount
/
