Dedicated Micros TransVu Express Quick start guide

Dedicated Micros
Brand
Dedicated Micros
Model
TransVu Express
Type
Quick start guide

Dedicated Micros TransVu Express

The TransVu Express is a versatile device designed for use in various applications, including vehicle surveillance and monitoring. It features a range of capabilities that make it suitable for a variety of use cases.

Key Features:

  • Video Recording: Records up to eight video channels simultaneously, providing comprehensive surveillance coverage.
  • Remote Access: Allows for remote monitoring and configuration via web interface or PC software, enabling real-time access to footage.
  • Event Triggering: Configurable event triggers initiate recording based on specific criteria, such as motion detection or alarm activation.

Dedicated Micros TransVu Express

The TransVu Express is a versatile device designed for use in various applications, including vehicle surveillance and monitoring. It features a range of capabilities that make it suitable for a variety of use cases.

Key Features:

  • Video Recording: Records up to eight video channels simultaneously, providing comprehensive surveillance coverage.
  • Remote Access: Allows for remote monitoring and configuration via web interface or PC software, enabling real-time access to footage.
  • Event Triggering: Configurable event triggers initiate recording based on specific criteria, such as motion detection or alarm activation.
Quick Start Guide
MI-Q-TVE/E2-0
Installing the Hard Drive
The hard drive for the unit is provided un-installed.
1) Unlock the keylock on the front of the TransVu Express and withdraw
the caddy.
2) Remove from the protective packaging from the Hard drive and insert
into the caddy. Ensure the pins on the hard drive are pointing away
from the front of the caddy drawer and the label on the hard drive
is facing upwards and visible when the hard drive is placed in the
caddy.
3) Carefully slide the caddy back into the TransVu Express. Remember
to lock the caddy into the TransVu Express using the keylock. Failure
to do so will prevent the unit starting up.
Connections
Please ensure the following are available and have been tested prior to the
installation:
• 10~30VDCVehiclePowerSource
• Crossednetworkcablerequiredforwebpagesetup
• Activevideosignals.
• Correctlyterminatedcableloom,pleaseseeTransVuExpress
installation manual for further information.
• DeskorLaptopPCwithCDROMdrivewithInternetExplorer5.5
upwardsforunitconguration
• Notethatpin35oftheconnectorprovidesaswitchedoutputofthe
inputvoltageNOTa12Vregulatedsupply
WARNING: Operate the TransVu Express from the power source
indicated on the label. Failure to do so may cause injury, and
will invalidate the warranty. Under no circumstances make
connections to this unit whilst power is applied
.
37 way Connector Layout
Numbers looking at the front of the male connector.
1 19
3720
Read the Instructions First
Read all safety and operating instructions and labels before working with the
TransVu Express. This Quick Start Guide is not for use in isolation and should
always be used in conjunction with the main user manuals.
Pleasecontactthesupplierwithanyproblems.Reportanydifcultieswiththis
guidetoDedicatedMicrosattheUKofce.Addressesandphonenumbers
are given in the user guides and also in the Contacts area of the website at:
http://www.dedicatedmicros.com
Servicing
Donotattempttoservicethisunit.Openingorremovingcoversmayexpose
dangerousvoltagesorotherhazards.Referallservicingtoqualiedservice
personnel.
Lifting and Handling
Alwaysfollowhealthandsafetyguidelineswhenliftingtheunitfromthebox
or installing the TransVu Express unit.
Unpacking
Remove all the items from the box and check components listed below are
included.
The TransVu Express package contains the following items:
• TransVuExpressunit
• MountingPlate
• RubberShockMounts
• InstallationCDROM
• InstallationGuide
• Conguration&OperationGuide
• SetupGuide
• QuickStartGuide(thisdocument)
Ifanyoftheseitemsaremissing,pleasecontactthedistributerCustomer
Services department.
Location
• Drillingextraholesinthecasingoftheunitwillimmediatelyinvalidate
the warranty.
• Theunitshouldbemountedawayfromanypossibleplaceswhere
water may puddle during vehicle operation as the TransVu Express
casing is not rated for submersion.
The unit should be mounted on a secure base free from resonance and
secondary vibrations using the mounting plate provided.
• Atmentareaof290mmx190mmx90mm(11½”x7½”x3½”)is
required.
• Extraspaceisrequiredaroundtotheplugareatoensureeasy
removal.
• RefertoTransVuExpressInstallationandConguration&Operation
Guides for more information.
Pin Description
1
MonitorOutput(1Vp-pCVBSvideo)
2 Video ground
3 Camera8(1Vp-pCVBSvideo)
4 Camera5(1Vp-pCVBSvideo)
5 Videoground
6 Camera4(1Vp-pCVBSvideo)
7 Camera1(1Vp-pCVBSvideo)
8 Audioground
9 AudioInput2(mic-level)
10Relayoutput(negativeside)
11COM3port:RS-232TXD
1210/100Ethernetport:TX+
1310/100Ethernetport:TX-
14AlarmInput1
15AlarmInput3
16 Switched power output – negative
17Powerinput-negative:ground
18Powerinput-negative:ground
19Videoground
Pin Description
20Camera7(1Vp-pCVBSvideo)
21Camera6(1Vp-pCVBSvideo)
22 Video ground
23Camera3(1Vp-pCVBSvideo)
24Camera2(1Vp-pCVBSvideo)
25Videoground
26AudioInput1(line-level)
27Relayoutput(positiveside)
28Alarmground
29AlarmInput2
30Ignitionsenseinput
31COM3port:RS-232RXD
32COM3ground
3310/100Ethernetport:RX+
3410/100Ethernetport:RX-
35Switchedpoweroutput–positive(1A)
36Powerinput-positive:10V–30VDC
37Powerinput-positive:10V–30VDC
15 way Expansion Port Layout
Numbers looking at the front of the male connector.
1
6
5
10
15
11
PIN NO. FUNCTION
1 POWERMANGERRS232-RXD
2 POWERMANGERRS232-TXD
3 GND
4 COM1RS232-RXD
5 COM1RS232-TXD
6 COM2-RS485+/RS422_TX+
7 COM2-RS485-/RS422_TX-
8 GND
9 COM1CTS
10 COM1RTS
11 COM2-RS422_RX+
12 COM2-RS422_RX-
13 GND
14 AUDIOOUT0linelevel
15 AUDIOOUT1linelevel
Quick Start Guide
MI-Q-TVE/E2-0
LED’s
The six status LEDs are on the opposite end of the unit to the
connector.
They are labelled as follows:
HDD NET
PWR
REC
FAIL
CF/SD
Description Function
HDD Illuminatesredtoindicatepowertotheharddiskdrive
CF/SD IlluminatesredtoindicatepowertotheCF/SDslots
PWR IlluminatesgreenwhenPowerisconnectedtotheunit
REC Illuminatesgreenwhentheunitisrecording
NET Illuminatesgreenwhentheunitisconnectedtothenetwork
FAIL Illuminatesgreenuntiltheunitsensesafailurecondition
Accessing & Conguring the Unit
The unit can be congured either on the local monitor or over the network
using a PC with Internet Explorer or similar browser. Both have near
identical menu interfaces.
Accessing the menus on a PC web browser
Locating the Unit IP address
The IP address of the unit is required to access the webpages. It can be
identied from the conguration menu pages using the local monitor, press
the MENU button on the IR Remote Control and navigate to the System
Settings->System menu to nd the DHCP assigned IP address.
Note: The unit can be connected to a DHCP network environment via
the 15 way connector to allow an IP address, subnet mask and
default gateway to be automatically be allocated by the network
DHCP Server (DHCP is enabled by default).
Note: If a DNS (Domain Name Server) address is not to be used, it is
strongly advised that a xed IP address be assigned (a DHCP
assigned address can change without notication i.e. following
power failure).
A xed IP address can be assigned via the Network Settings-
>Network menu.
For information on locating the unit’s IP address via a PC and serial port
connection, refer to Appendix D in the installation manual
.
Default DNS Address
It is recommended that a DNS (Domain Name Server) address be
congured. Assigning a recognisable name can help a remote user to
locate the unit.
If no System name is allocated to the unit, the default DNS address will
be:
machine serial number.yourdomain.com
• <machineserialnumber>isdisplayedintheSystem
menu page and also on the
underside of the unit.
• <yourdomain> isthenameassignedtoyour
DNSnetwork.
The default DNS address can be renamed via the Network Settings ->
Network menu. Following renaming, the DNS address will be:
yourname.yourdomain.com
• ’yourname‘ isthenameassignedviathe
Networkmenu.
• <yourdomain> isthenameassignedtoyour
DNSnetwork
Note: To activate an assigned DNS address, it will be necessary
to reboot the unit. The unit can be rebooted via System
Settings:>Maintain-> Reset.
IMPORTANT: To set the time and date on the unit, navigate to System
Settings->Time and Date.
Accessing the Conguration Webpages
The unit can be congured using the webpages. To access these:
1. LaunchInternetExplorer(orsimilarwebbrowserpackage).
2. TypetheURLfortheunit(IPorDNSaddress).
3. TheOpeningmenupagewillbedisplayed.
  • Page 1 1
  • Page 2 2

Dedicated Micros TransVu Express Quick start guide

Dedicated Micros
Brand
Dedicated Micros
Model
TransVu Express
Type
Quick start guide

Dedicated Micros TransVu Express

The TransVu Express is a versatile device designed for use in various applications, including vehicle surveillance and monitoring. It features a range of capabilities that make it suitable for a variety of use cases.

Key Features:

  • Video Recording: Records up to eight video channels simultaneously, providing comprehensive surveillance coverage.
  • Remote Access: Allows for remote monitoring and configuration via web interface or PC software, enabling real-time access to footage.
  • Event Triggering: Configurable event triggers initiate recording based on specific criteria, such as motion detection or alarm activation.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents