Metra 108-CH4DK Operating instructions

Brand: Metra

Model: 108-CH4DK

Category: Car kits

Type: Operating instructions

This manual is also suitable for

Metra 108-CH4DK is a car installation kit that lets you seamlessly integrate an 8-inch Pioneer DMH-C5500NEX radio into your Jeep Commander (without NAV) from 2006-2007. It's designed to match the factory finish in Dark Khaki, ensuring a cohesive look with your vehicle's interior.

Key Features:

Custom Fit: Specifically engineered for the Pioneer DMH-C5500NEX radio, providing a secure and stable installation.
Factory-Matched Finish: Painted in Dark Khaki to seamlessly blend with your Jeep's interior.
Complete Kit: Includes all necessary components for a hassle-free installation, including a radio bezel, brackets, retaining caps, and screws.

Key Features:

Custom Fit: Specifically engineered for the Pioneer DMH-C5500NEX radio, providing a secure and stable installation.
Factory-Matched Finish: Painted in Dark Khaki to seamlessly blend with your Jeep's interior.
Complete Kit: Includes all necessary components for a hassle-free installation, including a radio bezel, brackets, retaining caps, and screws.

Metra. The World’s Best Kits.

INSTALLATION INSTRUCTIONS

108-CH4

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• Designed speciﬁcally for the Pioneer DMH-C5500NEX 8-inch radio

• Painted to match the factory ﬁnish:

• 108-CH4G - Gray

• 108-CH4DK - Dark Khaki

KIT COMPONENTS

• A) Radio bezel • B) Radio brackets • C) Retaining caps • D) Philips screws (4)

TOOLS REQUIRED

• 9/32” Socket wrench • 5mm Allen screwdriver

• Cutting tool • Panel removal tool

• Phillips screwdriver • Solder gun

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation .......................................................3

Kit Assembly ..........................................................3

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: CHTO-01

Antenna Adapter: 40-CR10

A B C D

Jeep Commander (without NAV) 2006-2007

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

386.257.1187

MetraOnline.com

1. Remove (16) 5mm Allen screws securing

the dashboard trim panel. (Figure A)

2. Unclip and remove the dashboard trim

panel. (Figure B)

3. Remove (4) 9/32” screws securing the

radio. Slide the radio out, then unplug

and remove.

Continue to Kit Preparation

DASH DISASSEMBLY

(Figure B)

(Figure A)

(4) screws (4) screws (4) screws (4) screws

REV. 4/14/2020 INST108-CH4

From the factory dashboard trim panel:

1. Using either a solder gun or cutting tool,

remove the plastic welds holding the

factory radio bezel in place. (Figure A)

2. Using a pry tool, remove the factory

radio bezel from the center of the

factory dash panel.

Note: Be sure NOT to damage the holes

in the dash panel, so they can be used for

mounting the radio bezel in the next step

3. Clip the radio bezel in, then place the

retaining caps over the (4) screw holes.

Using a manual screwdriver, secure

using (4) Phillips screws provided.

(Figure B)

Continue to Kit Assembly

KIT PREPARATION KIT ASSEMBLY

(Figure A)

(Figure B)

Attention! For steps 1 and 2, reference the

installation manual provided with the radio

for which hardware to use. The display

screen and radio chassis use two different

types of screws

1. Secure the radio chassis to the radio

brackets using (4) screws supplied with

the radio. (Figure B)

2. Secure the display screen to the radio

brackets using (4) screws supplied with

the radio. (Figure A)

3. Locate the factory wiring harness and

antenna connector in the dash and

complete all necessary connections to

the radio. Metra recommends using

the proper mating adapter from Metra

and/or Axxess. Test the radio for proper

operation.

4. Slide the radio into the dash, then

secure using the factory screws.

Reinstall the dash in reverse order of

disassembly to complete the installation.

(Figure A)

(Figure B)

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certiﬁed technicians

Metra. The World’s Best Kits.

INSTALLATION INSTRUCTIONS

108-CH4

If you are having difﬁculties with the installation

of this product, contact our Tech Support line

either by phone at 386-257-1187, or email at

techsupport@metra-autosound.com. Before

doing so, look over the instruction booklet a

second time and ensure that the installation was

performed exactly as the instruction booklet

is stated. Have the vehicle apart and ready to

perform troubleshooting steps before contacting

Metra/Axxess Tech Support.

Metra 108-CH4DK Operating instructions

Brand: Metra

Model: 108-CH4DK

Category: Car kits

Type: Operating instructions

This manual is also suitable for

Key Features:

Custom Fit: Specifically engineered for the Pioneer DMH-C5500NEX radio, providing a secure and stable installation.
Factory-Matched Finish: Painted in Dark Khaki to seamlessly blend with your Jeep's interior.
Complete Kit: Includes all necessary components for a hassle-free installation, including a radio bezel, brackets, retaining caps, and screws.

Download PDF

report

Metra 108-CH4DK Operating instructions

This manual is also suitable for

Metra 108-CH4DK Operating instructions

Related papers

Other documents