Rhino-Rack 32112 Installation guide

Brand
Rhino-Rack
Model
32112
Type
Installation guide

Below you will find brief information for Sunseeker 32112. The Sunseeker 32112 is an awning side wall extension designed for use with Rhino-Rack Sunseeker 2 or 3 awnings. It fits both 2.0m and 2.5m models. The extension utilizes poles, guy ropes, and metal pegs for secure setup. It is important to use pegs and ropes, especially in windy conditions. It's recommended to check bolt connections regularly. It easily attaches to the main awning with velcro. The product must be removed when using automatic car washes.

Below you will find brief information for Sunseeker 32112. The Sunseeker 32112 is an awning side wall extension designed for use with Rhino-Rack Sunseeker 2 or 3 awnings. It fits both 2.0m and 2.5m models. The extension utilizes poles, guy ropes, and metal pegs for secure setup. It is important to use pegs and ropes, especially in windy conditions. It's recommended to check bolt connections regularly. It easily attaches to the main awning with velcro. The product must be removed when using automatic car washes.

Rhino-Rack Sunseeker Awning Side Wall Extension (32112)
Important: Please read these instructions carefully prior to installation.
Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
Check the contents of kit before commencing fi tment and report any discrepancies.
Place these instructions in the vehicle’s glove box after installation is complete.
Important Information
Recommendations
It is essential that all bolt connections be checked after driving a short distance when you fi rst install your Rhino-
Rack SUNSEEKER 2 or 3 Awning. Bolt connections should be checked again at regular intervals (probably once a
week is enough, depending on road conditions, usage, loads and distances travelled). You should also check the
roof bars and Side Wall extension each time they are refi tted.
Use only non-stretch fastening ropes or straps.
Please remove SUNSEEKER Awning, Side Wall Extension and crossbars when putting vehicle through an
automatic car wash.
Load Ratings
With the addition of the SUNSEEKER Awning, the load capacity of your crossbars will have to be adjusted accord-
ingly. The SUNSEEKER Awning and 2 crossbars weigh approximately 15kg.
Note for Dealers and Fitters
It is your responsibility to ensure this fi tting instruction is given to the end user or client
Rhino-Rack
3 Pike Street, Rydalmere,
NSW 2116, Australia. Document No: R238 Fit Time: 3-5min.
(Ph) (02) 9638 4744 Prepared By: Kayle Everett Issue No: 03
(Fax) (02) 9638 4822 Authorised By: Chris Murty Issue Date: 08/05/2017
These instructions remain the property of Rhino-Rack Australia Pty Ltd and may not be used or changed for any other purpose than intended.
Layout
Note: Use caution in windy conditions!
The pegs and ropes must always be used when the
SUNSEEKER 2 or 3 awning and the Side Wall extension are
open.
Page 1 of 3
This side wall extension  ts both 2.0m
and 2.5m Sunseeker Awnings
CONTROLLED
Rhino-Rack Sunseeker Awning Side Wall Extension (32112)
Page 2 of 3
Tools Required:
Mallet.
Care Instruction:
Wash and clean vehicle roof racks prior to fi tment
NOTE: AWNING SIDE WALL EXTENSION FITS BOTH
SUNSEEKER 2 or 3, 2.5m AND 2.0m AWNINGS
Parts List
Fitting Instructions
3
4
2
1
1Undo the velcro tabs holding
the horizontal support poles
in place. Position the poles
outwards slightly as shown. The
guy ropes will hold the awning
in place.
Item Component Qty Part No.
1 SUNSEEKER Side Wall
Extension 1 32112
2 Poles 2 C915
3 Guy Rope 2 C910
4 Metal Peg 3 C909
5 Fitting Instruction 1 R238
2Slide the awning into the pole as shown. Make sure the part with the velcro strips are facing out. Fix the
horizontal supports back in place.
Rhino-Rack Sunseeker Awning Side Wall Extension (32112)
Page 3 of 3
3Attach velcro tabs from awning to side wall extension as shown.
Side Wall Extension setup options
  • Page 1 1
  • Page 2 2
  • Page 3 3

Rhino-Rack 32112 Installation guide

Brand
Rhino-Rack
Model
32112
Type
Installation guide

Below you will find brief information for Sunseeker 32112. The Sunseeker 32112 is an awning side wall extension designed for use with Rhino-Rack Sunseeker 2 or 3 awnings. It fits both 2.0m and 2.5m models. The extension utilizes poles, guy ropes, and metal pegs for secure setup. It is important to use pegs and ropes, especially in windy conditions. It's recommended to check bolt connections regularly. It easily attaches to the main awning with velcro. The product must be removed when using automatic car washes.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents