Rhino-Rack 572 Installation guide

Brand
Rhino-Rack
Model
572
Type
Installation guide

Rhino-Rack 572 is a ski and snowboard carrier designed to securely transport your gear on the roof of your vehicle. It has a maximum load capacity of 79lbs/36kg when evenly distributed, allowing you to carry up to six pairs of skis or four snowboards. The carrier is easy to install and remove, and it comes with all the necessary hardware.

The Rhino-Rack 572 is made from durable materials and is designed to withstand the elements. It features a locking mechanism to keep your gear safe and secure, and it can be used on both round and square crossbars.

Here are some of the benefits of using the Rhino-Rack 572:

Rhino-Rack 572 is a ski and snowboard carrier designed to securely transport your gear on the roof of your vehicle. It has a maximum load capacity of 79lbs/36kg when evenly distributed, allowing you to carry up to six pairs of skis or four snowboards. The carrier is easy to install and remove, and it comes with all the necessary hardware.

The Rhino-Rack 572 is made from durable materials and is designed to withstand the elements. It features a locking mechanism to keep your gear safe and secure, and it can be used on both round and square crossbars.

Here are some of the benefits of using the Rhino-Rack 572:

Maximum Load Capacity evenly distributed inside ski carriers:
6 Pair = 79lbs/36kg.
4 Pair = 53lbs/24kg.
2 Pair = 26lbs/12kg.
3 Pair = 39lbs/18kg.
Recommendations:
It is essential that all bolt connections be checked after driving a short distance when you fi rst install your crossbars and acces-
sories. Bolt connections should be checked again at regular intervals (probably once a week is enough, depending on road con-
ditions, usage, loads and distances travelled). Please ensure that all loads are evenly distributed and that the centre of gravity
is kept as low as possible. Make sure to fasten your load securely.
Use only non-stretch fastening ropes or straps.
Caution: The handling characteristics of the vehicle changes when you transport a load on the roof. For safety reasons we
recommend you exercise extreme care when transporting wind-resistant loads. Special consideration must be taken into account
when cornering and braking.
Please remove crossbars & accessories when putting vehicle through an automatic car wash.
Off-road use:
Ski/ Snowboard Carriers are not recommended for off-road use.
Note for Dealers and Fitters:
It is your responsibility to ensure instructions are given to the end user or client.
Rhino-Rack
3 Pike Street, Rydalmere, Document No: R790 Fit Time: 10min
NSW 2116, Australia. Prepared By: Kayle Everett Issue No: 02
(Ph) (02) 9638 4744 Authorised By: Chris Murty Issue Date: 08/04/2016
(Fax) (02) 9638 4822
These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
Page 1 of 5
!
Rhino Ski/ Snowboard Carrier 572, 573, 574, 576
Important: Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
Check the contents of kit before commencing fi tment and report any discrepancies.
Place these instructions in the vehicle’s glove box after installation is complete.
CONTROLLED
Rhino Ski Carrier 572, 573, 574, 576
Page 2 of 5
Remove hardware.
Remove tube nuts, washers and T-bolts.
2
1Open ski carrier.
Turn the key anti-clockwise to unlock ski carrier.
Depress the button to open.
Key (vertical) in
unlocked position.
Tools Required:
5mm Security Allen key, provided in kit Tape measure.
Note:
When using round Yakima
Crossbars, remove the
Ski Carriers when not in use.
It is possible the Ski Carrier
could rotate in strong winds.
1
12
4
3
5
6,7
8
11
9
10
2
Parts List
Item Component Name Qty Part No.
1 Ski Carrier 2 -
2 Keys 4 -
3 M6 Spring Washer 4 W004
4 Top Clamp 4 M529
5 M6 x 40mm Security Screw 8 B085-BLK
6 M6 Flat Washer Black 8 W003-BLK
7 M6 Flat Washer Silver 4 W003
8 M6 Nut 8 N022-BLK
9 M6 Tube Nut 4 N038
10 Lower Clamp 4 M530
11 M6 x 30mm T-Bolt 4 B183
12 5mm Allen Key 1 H002
13 Instructions 1 R790
Rhino Ski Carrier 572, 573, 574, 576
Page 3 of 5
Position ski carriers.
Check ski carriers are in line when viewed from
front or rear of vehicle.
5
In line front to rear
Attach to crossbars.
Attach ski carriers to crossbars using hardware
supplied. Leave loose for adjustment.
4
M6 x 40mm
security screw
M6 fl at washer
Lower clamp
Attach top clamp.
Attach top clamp (M529). Fasten tube nut,
washers and T-bolt as shown, 2-3 lb/ft (3-4 Nm).
3
M6 tube nut
M6 spring washer
M6 fl at washer
Top clamp
M6 T-bolt
Rhino Ski Carrier 572, 573, 574, 576
Page 4 of 5
Transporting skis.
Ski carriers must be locked when transporting skis. Ski tips must face rearward.
8
Front of vehicle
7Locking the ski carrier.
Push top half down to clamp your skis until you here
the latch snap in place. Turn key clockwise to lock.
Remove key.
IMPORTANT: SKI CARRIER MUST ALWAYS BE
LOCKED WHEN CLOSED.
Key locked
89
Fasten ski carriers.
Check ski carriers are sitting square to the
crossbar. Tighten M6 screws on each clamp.
Tighten to 2-3 lb/ft (3-4 Nm).
DO NOT OVER TIGHTEN.
6
Rhino Ski Carrier 572, 573, 574, 576
Page 5 of 5
C-groove crossbars.
Measure and then cut the rubber strip to fi ll the gaps on
either side of the ski carriers.
b
C-groove crossbars.
Remove rubber buffer strip.
Remove Top & Bottom clamp, refer Step 2.
Locate T-bolts in the C-groove by sliding the whole
assembly into the top of the crossbar.
Position ski carriers in line as described in step 4.
Open ski carriers to tighten the M6 tube nuts, 2-3 lb/ft
(3-4 Nm).
C-groove with
T-bolt in place
Attaching Ski Carriers to C-groove of crossbar
a
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Rhino-Rack 572 Installation guide

Brand
Rhino-Rack
Model
572
Type
Installation guide

Rhino-Rack 572 is a ski and snowboard carrier designed to securely transport your gear on the roof of your vehicle. It has a maximum load capacity of 79lbs/36kg when evenly distributed, allowing you to carry up to six pairs of skis or four snowboards. The carrier is easy to install and remove, and it comes with all the necessary hardware.

The Rhino-Rack 572 is made from durable materials and is designed to withstand the elements. It features a locking mechanism to keep your gear safe and secure, and it can be used on both round and square crossbars.

Here are some of the benefits of using the Rhino-Rack 572:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents