TALA CP-OAK-LRG-01-EU Installation guide

Type
Installation guide
EU/UK
Scan me for more
technical help
FOR INDOOR USE ONLY
IP20 220  240V~
BEFORE STARTING
We advise the fitting of our canopy and pendants to be
peormed by a qualified electrician. Please read through
these instructions before commencing work, and keep them
for future reference. Please take extreme care when carrying
out these instructions.
IMPORTANT
This light fitting must be connected to the supply earth.
If your lighting circuit does not have an earth, ask a
qualified electrician to provide an earth facility. This light
fitting is suitable for indoor use only. This fitting operates
on 240V mains voltage. Please visit our website to see our
recommended dimmers.
WARNING
You must switch o electricity supply at the mains during
installation and maintenance. We strongly recommend that
you withdraw the fuse or switch o the circuit breaker whilst
work is in progress. Do not only turn o the wall switch. All
fittings must be installed in accordance with current Building
Regulations and IEE Wiring Regulations.
RECOMMENDED EQUIPMENT
- Small Flat-head and Phillips-head screwdriver
- Wire strippers
- Insulation tape
- 17mm spanner
- 7mm spanner
- Power drill with 10mm and 5mm drill bit
(Always use the correct drill bit for the material)
Thoughul lighting, responsibly designed in London.
Thank you for making the switch to Tala.
Discover the full Tala family at tala.co.uk
Installation Guide
LARGE CANOPY
SKU  CPASHLRG01EU
SKU  CPWALTLRG01EU
SKU  CPOAKLRG01EU
Large Canopy - Provided Components
x12 Cord Grips
x1 Ceiling Plate
A
A
x1 Junction Box
x1 M4 20MM Bolt
x3 Safety Tethers
and Clips
C
C
B
B
x1 Ceiling Bracket
D
D
E
E
F
F
A
B
D
STEP 1
Unhook the three safety
tethers from the plate
Set ceiling bracket with
tether to one side.
B
A
D
STEP 2A  REVERSE OR REPLACE
DISPLAY PANEL OPTIONAL
Remove panel and display disk by
loosening nut and washer .
To display the alternative finish, rotate
disc 180 degrees. Note, not all
display panels have an alternative
finish.
3
3
3
2
2
1
1
B1
B1
B2
STEP 2B
Re-assemble the plate in
the same order and fasten
it securely with nuts and
washers .
Tighten these firmly with a
spanner/wrench.
2
1
1
2
4
3
STEP 4
Flip the panel over to the
visible side and, using a 10mm drill
bit, drill final holes through the
pilots on the visible side.
Again we recommend using a
sacrificial suace.
STEP 3
Once you have chosen the hanging
positions of your pendants, with a 5mm
drill bit, drill small pilot holes through
panel from the back side .
Please take your time drilling these
holes. We recommend you clamp the
plate onto a sacrificial suace .
This will stop the plate moving and help
give a clean hole on the front suace.
4
3
4
3
3
STEP 5
Fasten cord grips through the
holes you have drilled using
the toothed washers and
nuts .
Tighten these firmly with a
spanner/wrench.
6
65
5
STEP 6
Attach to the ceiling using
screws and plug. Make sure to
use screws and plugs that are
appropriate for the ceiling type.
A
A
Mains supply
Earth
240V
Fixings not
included
STEP 7
Attach ceiling plate to ceiling
bracket using safety tether
clips .
A
D
B
A
B
D
C
F
STEP 8
Thread all nine pendant cables
through ceiling plate cord
grips .
F
C
STEP 9
Pull cables through to your
desired length.
See end of this guide for our
recommended lengths and
distance between bulbs.
Using a flat head screwdriver,
tighten set screws to secure
them.
STEP 10
Cut o excess cable and strip
wires to expose the copper core.
Maintain all double insulation.
C
C
N
L
Mains supply
Earth tag from ceiling bracket
Brown or Red (L)
Blue or Black (N)
Pendants
Pendants
Brown or Red (L)
Household Earth
Earth tag from ceiling plate
240V
240V
B
A
Pendants
Blue or Black (N)
STEP 11
Connect the pendants, plate and mains
wiring as shown.
A
2
B
1
STEP 12
Li to sit flush with .
Make sure the pins are located at the
opening of the bayonet fitting
STEP 13
Rotate plate anti-clockwise until
the pin is locked into the bayonet
mechanism .
Secure plate in place using bolt .
There will be a small shadow gap
between the canopy and the ceiling.
B
B
A
B G
1
1
2
2
G
2
B
1
A
B
MINIMUM CORD LENGTH
For all bulbs shortest recommended
cord length is 350mm
A
DISTANCE BETWEEN PENDANTS
Recommended minimum distance
between pendant, dependant on
bulb style, are as follows:
Voronoi I - 150mm
Voronoi II - 200mm
Voronoi III - 350mm
Sphere IV - 150mm
All other bulbs - 100mm
B
ADJUSTING THE CORD
To adjust the cord to your desired length, using a
flat head screw driver, loosen the grub/set screw
and push the cable up into the ceiling plate.
Secure the cable in place by
re-tightening the grub screw.
Maintain all double insulation.
1
1
PENDANT DISPLAY GUIDE
PENDANTS  RECOMMENDED CABLE LENGTHS
SCENARIO 1
Above a coffee or dining table,
or where height is required for
seated tasks
Minimum Distance
700mm
SCENARIO 2
Above side tables, or where
height is required for storage
Minimum Distance
500mm
SCENARIO 3
Above a kitchen island or bar,
or where height is required for
standing tasks
Minimum Distance
800mm
Minimum Distance
2.2m
SCENARIO 4
Above a stairwell or walkway,
or where height is required for
walking underneath
WARRANTY AND AFTERCARE
This product has a two-year warranty. If there appears to be
a functional defect with the product during this time, please
contact our team at [email protected].uk.
Please note, the flexible cable attached to this luminaire cannot
be replaced; if the cable is damaged, recycle the luminaire and
seek a replacement.
Join the Community
Instagram: @tala | Facebook: talaHQ | Pinterest: TalaLED | Tag: lighttoliveby
Tala Energy Ltd. 25B Vyner Street, London E2 9DG | hello@tala.co.uk
Tala Europe B.V, Bertus Aafjeshove 40, Nieuwegein 3437JN, Netherlands
This symbol indicates that electrical and electronic equipment (WEEE) should not
be mixed with general household waste.
For recovery and recycling, please take this product to a designated collection point
where it will be accepted free of charge. Many retailers oer this in-store. Disposing
of this product correctly will help save valuable resources and prevent any potential
negative eects on human health and the environment.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

TALA CP-OAK-LRG-01-EU Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI