Anderic KTN828 Operating instructions

Brand
Anderic
Model
KTN828
Category
Electrical timers
Type
Operating instructions
Anderic KTN828 Operating Manual
The KTN828 is designed to work with most air conditioners that require a remote control.
Note: Sliding the door panel on the front-bottom of the remote down will expose the rest of the
keys including the “SELECT” key used for programing. Also, take note of the numbers located
on the bottom left corner of each key. These keys are used for entering the codes. See section
below for programming using code input.
Install batteries
To install batteries, simply slide off the battery cover on the back of the remote. Please make
sure to install 2 AAA batteries, taking note of the polarity marks located in the compartment.
Programming using code input
1. Take note of the codes beside the brand of your AC in the code section of this manual.
2. Press the ”SELECT” key, the code section on the screen will flash.
3. Enter the first 4-digit code beside your brand from the code section.
a. Remote should now operate AC, if it does not, please repeat from step 2 with the
next code from the code section.
b. After you find a code that is working try other function keys to see if they work. If
you feel that the other keys should be working, then you can try a different code
to see if there is a better code that works more fully.
Programming using auto-search
If you do not know the brand of your air conditioner, or if your brand is not listed in the code
table, please operate as per following steps:
1. Aim the remote control at your air conditioner during this whole process.
2. Press the “SELECT” key for 5 seconds and then release, remote control has entered
auto-search status. The remote is now sending codes continuously.
3. When AC responds, immediately press any key on the remote to save the current code
quickly.
4. Try other function keys to test to see if code works fully, if not, please repeat steps
above.
Intelligent Cooling & Intelligent Heating
In the summer, press the “Intelligent Cooling” only, the air conditioner will be cooled
immediately. In the winter, press the “Intelligent Heating” key only, the air conditioner will be
heated immediately. In both status, the air conditioner will let the heating and cooling in a
comfortable temperature automatically, and the fan and swing are all automatic. At the same
time, user can also adjust the temperature by “Temp.+/-” keys as needed.
Clock set up
1. Press the “CLOCK” key, clock signal flashes.
2. Press “Time +/-” keys to adjust the current time.
3. Press the “CLOCK” key again to save and exit.
Timer operations:
Notes:
1. If to press the “TMR ON” or “TMR OFF” key twice, timer will cancel.
2. After setting the timer feature with the remote, make sure to put remote in a stationary
position in direct line of sight with the AC unit, or timer feature will not work.
3. If to view the remaining time of timer, pressing the “TIMER ON” or “TIMER OFF” key.
Timer on
1. Press the “TMR ON” key, the time section on LCD starts flashing.
2. Press “TIME +/-” keys to adjust the time when you want to make the AC turn on
automatically.
3. Time on LCD will stop flashing after 15 seconds. Setting is complete.
Timer off
1. Press the “TMR OFF” key, the time section on LCD starts flashing.
2. Press “TIME +/-” keys to adjust the time when you want to make the AC turn off
automatically.
3. Time on LCD will stop flashing after 15 seconds. Setting is complete.
Toggling Celsius & Fahrenheit
1. Press the “C/F” key.
Sleep function
In the summer, press the “SLEEP” key while it is in cool mode, the temperature will be raised
1ºC per hour in the first 2 hours and will be shut off by itself after 8 hours. In the winter, press
the “SLEEP” key while it is in heat mode, the temperature will fall 1ºC per hour in the first 2
hours and AC will shut off after 8 hours. After setting sleep function, make sure to put remote in
a stationary position in direct line of sight with the AC unit, or sleep feature will not work.
Other notes about the KTN828
1. If remote is to be stored and not used for a long time, please remove the batteries to
avoid and possibility of corrosion or leakage due to the batteries going bad.
ANDERIC® is a registered trademark of Dan’s Electronics Etc. Inc.
For support, please visit Anderic.com/KTN828 or call 1-855-263-3742.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Anderic KTN828 Operating instructions

Brand
Anderic
Model
KTN828
Category
Electrical timers
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents