PAC NDK748G User manual

Type
User manual

This manual is also suitable for

PAC NDK748G is a mounting kit that allows you to install a Double DIN or Single ISO mountable radio into your 2013-14 Nissan Sentra. The kit includes everything you need to install your new radio, including brackets, screws, and metal clips.

The NDK748G is easy to install and can be completed in just a few steps. First, you will need to disassemble your dash and remove your old radio. Then, you will need to insert your new radio into the NDK748G brackets and attach it to the sides of the radio.

Once your radio is in place, you will need to test fit the kit to make sure that everything aligns correctly. If everything looks good, you can then attach the metal clips to the mainframe and snap the mainframe into place.

PAC NDK748G is a mounting kit that allows you to install a Double DIN or Single ISO mountable radio into your 2013-14 Nissan Sentra. The kit includes everything you need to install your new radio, including brackets, screws, and metal clips.

The NDK748G is easy to install and can be completed in just a few steps. First, you will need to disassemble your dash and remove your old radio. Then, you will need to insert your new radio into the NDK748G brackets and attach it to the sides of the radio.

Once your radio is in place, you will need to test fit the kit to make sure that everything aligns correctly. If everything looks good, you can then attach the metal clips to the mainframe and snap the mainframe into place.

CUSTOMER HELP LINE
USA 800-323-4329 Canada 800-245-8777
iNDK748G
Automotive Products Division
1040 Avenida Acaso Camarillo, CA 93012, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006 USA Fax (805) 388-7950
For information about other American International automotive
accessories visit our website at:
http://www.americaninternational.net
NDK748G Mounting Kit
Nissan
2013-14 SENTRA
VEHICLE APPLICATIONS
©2014 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 5/14 PRINT Ver. 5/14
IMB748G LEFT
IMB748G RIGHT
Fig B
MAIN FRAME
DASH DISASSEMBLY AND RADIO REMOVAL
1 2
KIT ASSEMBLY INSTRUCTIONS
Note: DO NOT snap metal clips to mainframe until you are at step 5.
1. Insert pocket into lower section of the NDK748G brackets. See fig A
2. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible, or screws supplied with kit.
3. Slide radio forward or backward for desired look and tighten screws.
4. Test fit kit/radio by making sure the main frame of the NDK748G aligns correctly and
does not leave any gaps when installed. If everything looks correct go to step #5.
If not, go back to step # 3.
5. Attach the 4 metal clips supplied to the mainframe See Photo B.
Snap mainframe to the dash pressing firmly on the bottom right and left, and then
the top right and left.
6. Suggested…Attach a rear support bracket to the rear of the new radio and adjust as
necessary to support the weight of the radio.
Single ISO Mount Applications
F
ig A
1. With a soft tool loosen the dash panel surrounding the radio. Remove. See Photo A.
2. Remove (4) Phillips screws securing the radio brackets to the sub dash.
3. Remove radio and unplug all harnesses and antenna connections.
MAI
N F
RAME
IMB748G LEFT
POC7
4
8
G
IMB7438G RIGHT
CORRECT
NOT CORRECT
Double DIN Mount Applications
See Fig B
Note: DO NOT snap metal clips to mainframe until you are at step 4.
1. Insert ISO mountable radio between ISO mount brackets and loosely attach to
sides of radio using screws provided with radio when possible, or screws supplied
with kit.
2. Slide radio forward or backward for desired look and tighten screws.
3. Test fit kit/radio by making sure the main frame of the NDK748G aligns correctly
and does not leave any gaps when installed. If everything looks correct go to
step #5. If not, go back to step # 3.
4. Attach the 4 metal clips supplied to the mainframe See Photo B. Snap mainframe
to the dash pressing firmly on the bottom right and left, and then the top right
and left. 5.Suggested…Attach a rear support bracket to the rear of the new radio
and adjust as necessary to support the weight of the radio.
KIT ASSEMBLY INSTRUCTIONS
  • Page 1 1
  • Page 2 2

PAC NDK748G User manual

Type
User manual
This manual is also suitable for

PAC NDK748G is a mounting kit that allows you to install a Double DIN or Single ISO mountable radio into your 2013-14 Nissan Sentra. The kit includes everything you need to install your new radio, including brackets, screws, and metal clips.

The NDK748G is easy to install and can be completed in just a few steps. First, you will need to disassemble your dash and remove your old radio. Then, you will need to insert your new radio into the NDK748G brackets and attach it to the sides of the radio.

Once your radio is in place, you will need to test fit the kit to make sure that everything aligns correctly. If everything looks good, you can then attach the metal clips to the mainframe and snap the mainframe into place.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI