Panasonic VLSWD501FX Operating instructions

Category
Door intercom systems
Type
Operating instructions

This manual is also suitable for

Panasonic VLSWD501FX is a wireless video intercom system that allows you to see and talk to visitors at your door from anywhere in your home. It comes with a main monitor and a doorphone, which can be installed either surface-mounted or flush-mounted. The system features a 3.5-inch color LCD screen, a built-in microphone and speaker, and the ability to connect to up to two doorphones and two additional monitors. It also has various functions such as door release, call transfer, and image recording.

Panasonic VLSWD501FX is a wireless video intercom system that allows you to see and talk to visitors at your door from anywhere in your home. It comes with a main monitor and a doorphone, which can be installed either surface-mounted or flush-mounted. The system features a 3.5-inch color LCD screen, a built-in microphone and speaker, and the ability to connect to up to two doorphones and two additional monitors. It also has various functions such as door release, call transfer, and image recording.

Installation Guide
Note to the installer
■ Beforeattemptingtoconnectoroperatethisproduct,pleasereadthelabelontherearof
themainmonitor.
■
Pleasereadthis
guide
carefully,andinstalltheproductsafelyandcorrectlybyfollowing
theinstructions.Carefullyreadtheinformationfoundinthesectiontitled"Foryoursafety"
inparticular.
■
Onlyuseattachments/accessoriesspecifiedbythemanufacturer.
■
Theinstallationshallbecarriedoutinaccordancewithallapplicableinstallationrules.
■
Panasonicassumesnoresponsibilityforinjuriesorpropertydamageresultingfromfailures
arisingoutofimproperinstallationoroperationinconsistentwiththisguide.Additionally,
anyresultingmalfunctionwillnotbecoveredunderthewarranty.
■ Afterinstallation,makesuretoleavethisguidewiththecustomer.
For the Installation of door station
and main monitor station
•VL-V554isasurfacemounttype,VL-V554Uisaush
mounttype.
•Inthismanual,thesufxofeachmodelnumber(e.g.,
the"FX"in"VL-SWD501FX")isomitted.
For your safety
Topreventsevereinjuryandlossoflife/property,readthissectioncarefullybeforeusingthe
producttoensureproperandsafeoperationofyourproduct.
WARNING
Preventingre,electricshockandshortcircuits
Leaveinstallationworktothedealer.
Installationworkrequirestechniqueandexperiences.Failuretoobservethismay
causere,electricshock,injury,ordamagetotheproduct.Consultthedealer.
Electricalconnectionworkshouldbeperformedbycertiedpersonnelonly.Certication
isrequiredforperformingelectricalconnectionwork.Consultyourdealer.
Useonlythespeciedpowersupplyunit.
Donotattempttodisassembleormodify thisproduct. Contactanauthorisedservice
centreforrepairs.
Neverinstallwiringduringalightningstorm.
Donotconnectnon-specieddevices.
Donotconnectapowercabletoaterminalthatisnotspeciedinthisguide.
When opening holes inwallsforinstallation or wiring,or whensecuring the power
cable,makesureyoudonotdamageexistingwiringandductwork.
Donotmakeanywiringconnectionswhenthepowersupplyisturnedon.
Donotusethesuppliedpowersupplyunitforoutdoorinstallations(itisforindooruseonly).
Donotinstallthemainmonitorandpowersupplyunitinthefollowingplaces:
- Placeswherethemainmonitorandpowersupplyunitmaybesplashedwithwateror
chemicals.
- Placeswherethereisahighconcentrationofdust,orhighhumidity.
Donotperformanyactions(suchasfabricating,twisting,stretching,bundling,forcibly
bending,damaging,altering,exposingtoheatsources,orplacingheavyobjectsonthe
powercable) thatmaydamage thepowercable. Usingthe productwithadamaged
powercablemay cause electricshock, short circuits, orfire. Contactanauthorised
servicecentreforrepairs.
When existing chime wires are used, it ispossible that they containAC voltage.
Contactanauthorisedservicecentre.
Donotinstallor use theproductin healthcare facilitiesifany regulationsposted in
the area instruct you not to do so. Hospitals orhealthcare facilities may be using
equipmentthatcouldbesensitivetoexternalRF(radiofrequency)energy.
Do not install orusethis product nearautomatically controlled devices such as
automatic doorsandfire alarms. Radiowavesemittedfromthis productmay cause
suchdevicestomalfunction,resultinginanaccident.
Preventingaccidentsandinjuries
CAUTION
Ifthewiringisunderground,donotmakeanyconnectionsunderground.
Ifthewiringisunderground,useaprotectiontube.
Ifthewiringisoutdoors,useaprotectiontubeorasurgeprotector.
Installtheproductsecurelyadhering totheinstructionsin thisguide toprevent itfrom
fallingoffthe wall.Avoidinstallingontolow-strengthwalls,suchasgypsumboard,ALC
(autoclavedlightweightconcrete),concreteblock,orveneer(lessthan18mmthick)walls.
Preventingelectricshock
Preventinginjury
VL-V554/
VL-V554U
VL-MWD501
Doorstation Mainmonitorstation
Doorstationisdescribedas"doorphone"
andMainmonitorstationisdescribedas
"mainmonitor"inthisguide.
ModelNo.
VL-SWD501
VL-SWD501U
Wireless Video Intercom System
Toavoidmalfunctionorcommunicationdisturbances,donotinstallthedoorphoneorthemain
monitorinthefollowinglocations:
- Placeswherevibrationoranyotherkindofimpactoccurs.
- Placeswhereechoingisfrequent.
- Placesnearahighconcentrationofdust,hydrogensulphide,ammonia,sulphur,ornoxious
fumes.
■
For the doorphone
Ifastronglightisshiningonthedoorphone,thevisitor’sfacemaynotbedistinguishable.Do
notplacethedoorphoneinthefollowinglocations:
- Wheremostofthebackgroundisthesky.
- Wherethebackgroundisawhitewall,anddirectsunlightwillreectoffit.
- Wheredirectsunlightwillshineonthedoorphone.
Do not place the doorphone in locationswhere echoing occurs, as this will cause the
doorphonetobeepfrequently.
Dustprotection/waterprotectionisIP54.
Onlywheninstallationworkspeciedinthisguideisproperlyperformedandappropriatewater
protectiontreatmentisperformed.
Makesuretherearofthedoorphoneisnotsubjecttowater.
Dependingontheinstallationlocation,condensationmayformonthedoorphone’slenscover.
Thismaycauseimagestobecomeobscured.Condensationwilldissipateasthetemperature
rises.
■
For the main monitor
Install the main monitor away from electronic appliances such asTVs, radios, personal
computers, airconditioners,boilercontrolpanelswithintercom,homesecurityequipment,
wirelessdevices,ordigitalcordlessphones.
Donotinstallthemainmonitorinplaceswhereitwillbeaffectedbyextremelyhigh-frequency
radiowaves(nearbroadcasting antennasetc.).This maycausethe displaytoicker oran
interruptingnoisetooccur.
Leave at least 20 cm of space above, below,and to the left and rightsides of the main
monitor.Donotinstallonawallthatisdeeplyrecessed.
Donotinstallthemainmonitorinsideawall.
Besuretoinstallthemainmonitormorethan5mawayfromthedoorphone.
The product operates in the frequency range of 1.88 GHz to 1.90 GHz, and the RF
transmissionpower is 250 mW (max.).Refertothe "Forbestperformance" section in the
OperatingInstructions.
Inareas surroundedbyahighelectricaleld,disturbancesmay occurinthemainmonitor’s
imageorsound.
Supplied accessories for installation
For the doorphone
(VL-V554only)
Mounting
base×1
(VL-V554Uonly)
Flush
mounting
box
×
1
Screw×4(Usedwhen
installingthedoorphone)
(VL-V554

:4mmx12mm)
(VL-V554U:4mmx25mm)
Nameplate×2
(incl.1spare)
Hexwrench×1
For the main monitor
Mounting
bracket×1
Cablebinder×1
■ Powersupplyunitandrelateditems
Powersupply
unit×1
(PartNo.VL-PS240)
Cablebinder×2
Important:
Youwillneedthefollowingadditionalitemstoinstallandcongurethedoorphone
and the main monitor.
[Locally procured]
- Screws(formountingbase:×2,formountingbracket:×2):
Preparethescrews(
thedrawingontheright)accordingto
thematerial,structure,strengthandotherfactorsofthemounting
areaandthetotalweightofobjectstobemounted.
- Powercables(AC/DCcables),wires(fordoorphoneandotherconnections):
Preparecablesandwiresoftheappropriatespecication.(
"Wiretypeandlength")
Note:
Theillustrationsinthesuppliedmanual(s)mayvaryslightlyfromtheactualproduct.
4mm
Precautionsforinstallation
Wiringschematicdiagram
Setupcorrectlyaccordingtothefollowingwiringschematicdiagramand"Wiretypeandlength".
Forinformation,suchasordernumbers,aboutoptionaldevicesthatcanbeconnectedto,refertothe"Additional/replacementaccessories"sectionintheOperatingInstructions.
MAIN MONITOR
DOORPHONE1
DOORPHONE2
POWERSUPPLYUNIT
220-240VAC
Connectiondeviceforoptionoutput(Acontact)
*1MakesuretoonlyconnectelectricvehiclegatelockstotheS3/S4terminalsofthe
doorphones.
*2MakesuretoonlyconnectelectricdoorlockstotheS1/S2terminalsofthedoorphones.
NP:Non-polarised
Power
supply
Power
supply
Power
supply
Power
supply
12VAC/DC
12VAC/DC
12VAC/DC
12VAC/DC
Electriclock
(Electricvehicle
gatelock)
*1
Electriclock
(Electricdoor
lock)
*2
Electriclock
(Electricdoor
lock)
*2
Electriclock
(Electricvehicle
gatelock)
*1
24VDC
Wiretypeandlength
Wiringrun
Wiretype
*1
Diameter Length(Max.)
Mainmonitor–
Doorphone
A
φ0.65mm 22AWG 100m
φ1.0mm 18AWG 130m
φ0.5mm CAT5 50m
Mainmonitor–
Powersupplyunit
B
φ0.65mm 22AWG 10m
φ1.0mm 18AWG 20m
Powersupplyunit–
ACpowersource
C
φ1.2mm-φ2.0mm
(17AWG-12AWG)
Norequirement
Doorphone–
Electriclock
*2
D
φ0.5mm-φ1.2mm
(24AWG-17AWG)
Accordingtospeci-
cationofconnected
device.
Mainmonitor–
Connectiondeviceforoption
output(Acontact)
*2
E
φ0.5mm-φ1.2mm
(24AWG-17AWG)
Accordingtospeci-
cationofconnected
device.
*1Type:Single-paircablewithoutersheath(jacket)
Conductor:Coppersolid
Acertiedpowersupplywiringhastobeusedwiththisequipment.Therelevantnational
installationand/orequipmentregulationsshallbeconsidered.Acertiedpowersupplywiring
notlighterthanordinarypolyvinylchlorideexiblewiringaccordingtoIEC60227shallbeused.
*2Whenusinganelectriclockoraconnectiondeviceforoptionoutput(Acontact),selectadevice
thatmeetsthefollowingguidelines:
Electriclockconnectionterminal(S1/S2,S3/S4):
- N/Odryclosurecontact
- 12VAC/DC,lessthan1A
Connectiondeviceforoptionoutput(Acontact)terminal(OUT1/OUT2):
- 24VAC/DC,lessthan0.3A(minimumcontact:5VDC1mA)
A D
D
E
B
C
NP
NP
NP
NP
NP
NP
NP
NP
1-62,4-chome,Minoshima,Hakata-ku,Fukuoka812-8531,Japan
©PanasonicSystemNetworksCo.,Ltd.2015 PNQW4915ZAC1015MM0
ScrewA
Youcanusethe[Wide/Zoomsettings]settingonthemainmonitortoselecttheareathat
isvisiblewhenavisitorcalls;availablesettingsare[Wide],[Zoom],and[All](entireimage
display).(Defaultsetting:[Wide])
Thefollowingvaluesareforwhenthedoorphoneisinstalledinthestandardposition(thecentre
of thedoorphone’s heightisapproximately1,450mm) andat adistanceofapproximately
500mmfromthecameralens.
■ Installationheightandareavisiblebythecameralens
When set to zoom
Displaysaportionofthewideimageat2timesthesize.
Because a digital zoom isused, the image quality of zoom
displayislowerthanthatofwidedisplayorentireimagedisplay.
Imagedisplayedon
mainmonitor:
Youcanusethemainmonitor’s[Zoompositionsettings]settingtoselectthedesiredarea
visiblewhenzooming.
Refertothefollowingandcongurethemainmonitor.
Entireimagedisplay
Theareaaboveandbelowthewideimageisvisible.
Important:
Onthebottomsurfaceofthedoorphoneandthemountingbase,thereareholestoallowwater
todrain.Donotcoverthemupwheninstalling.
Whenexistingwiring(suchaschimewires)isused:
- ItmaycontainACvoltagethatmaycauseelectricshockand/ordamagetheproduct.
- Neverusethefollowingtypesofwiring.Consultaqualiedtechnician/dealer.
VL-V554 VL-V554U
1
Attachthemountingbasetothewallsecurely.
Mountingbase
(accessory)
Wire(locallyprocured)
Wall
83.5mm
Screws(locallyprocured)×2
Installthemountingbaseonaverticalatwall.
1
Installtheflushmountingboxinthe
wall.
Flushmountingbox(accessory)
100mm
Knockouthole
*1
151mm
37mm
*1Onlyopentheknockoutholesas
requiredforthewiring.
2
Useahexwrench(accessory)toloosenscrewAandremovethefrontpanelofthedoor-
phone.
ScrewA
Frontpanel
2mmhexwrench
(accessory)
3
Connectthewires.
Terminalforthe
mainmonitor
<Rear
view>
Terminalsfortheelectriclocks
Recommendedtorque:
0.5N·m{5.1k
g
f·cm}
Maximumtorque:
0.7N·m{7.1k
g
f·cm}
3-1Loosenthescrews.
3-2Pushinthewirestotheterminalconnectors(non-polar),thentightenthescrews.
4
Attachthedoorphonetothemounting
base.
Screws(accessory)×4
4
Attachthedoorphonetotheflushmounting
box.
Screws(accessory)×4
5
AttachthenameplatetothedoorphoneandusescrewAtosecurethefrontpanel.
Writethenameonthenameplateasneeded.
Nameplate
(accessory)
ScrewA
Recommendedtorque:
0.35N·m{3.6k
g
f·cm}
Approx.500
Approx.170°
Approx.2,250
Imagerange
Approx.115°
Approx.500
Imagedisplayedon
mainmonitor:
Approx.1,600
Approx.650
Approx.1,450
Upanddown
Leftandright(whenlookingfromabove)
Up
Imagerange
Approx.2,050
Approx.500
Centreof
doorphone
Approx.45°
Centre (default)
Approx.45°
Approx.500
Imagerange
Approx.1,650
Down
Approx.45°
Approx.500
Approx.1,400
Imagerange
Left
Approx.1,500
Approx.1,450
Approx.550
Approx.1,450
Approx.1,250
Approx.400
Installingthedoorphone
■
Abouttheinstallationlocation
Thedevicemustbeinstalledinsideanelectricalpanelorcabinet.
Areadilyaccessibledisconnectdeviceshallbeincorporatedexternaltotheequipment.
- Externaldisconnectdevicemustbecertiedandhaveacreepageandclearancedistance
of3mmormore.
■
Precautionsforwiring
Makesureyouturnoffthepoweratthebreakerbeforeperforminganywiringwork.
Always connectAC or DC cables to the appropriate connection terminals. Incorrectly
connectingtheACorDCcablesmaydamagethepowersupplyunit.
Topreventthe powercables fromdisconnectingand toprevent electric shock,secure the
powercablesusingthecablebinders(accessory)andattachthecablecovers.
Howtoconnectthepowercable(AC/DC)
1
StriptheAC/DCcablesasfollows:
7mm
45mm
<ACcable>
<DCcable>
25mm
7mm
2
Removethescrews(
B
)andthenremove
thecablecovers(
A
).
3
ConnecttheAC/DCcabletotheACIN
terminal/DCOUTterminalonthetopand
bottomofthepowersupplyunit,andthen
securethewiresbytighteningthescrews.
Recommendedtorque:
- ACterminal:0.4N·m{4.1k
g
f·cm}
- DCterminal:0.45N·m{4.6k
g
f·cm}
<Frontview>
ACcable
*1
DCcable
Screws
*1
Cablebinders(accessory)
4
Usethecablebinders(accessory)to
securetheAC/DCcables(double-coated
area)tothepowersupplyunit.
5
Makesuretoreplacethecablecovers(
A
).
Connectthepowersupplyunit(accessory)andAC/DCcables(locallyprocured).
CAUTION
Insertthecablesfirmlyalltheway
intotheterminals.
Ifthecablesarenotinsertedall
theway,heatmaybegenerated.
*1Makesurethattherearenobarewires
exposedoutsidetheproduct.
Screws(
B
)
Cablecovers(
A
)
DCOUTterminal
ACcable
binderhole
ACINterminal
<Topview>
<Bottomview>
DCcable
binderhole
Powersupplyunit(withcablecovers
removed)
Attach to the DIN rail
Attachintheorderdescribedbelowsothathook(b)ispositionedatthebottom.
1
Hanghook(a)ontheDINrail(
A
).
2
Pullandholdtheleverdown(
B
).
3
Securehook(b)totheDINrail(
C
).
Hook(a)
A
B
C
Hook(b)
Main monitor installation position
Installingthemainmonitor
Mainmonitor
installationposition
82.5mm
82.7mm
2
ConnecttheDCcableandwires.
Connect thewires correctly accordingto"Wiringschematic
diagram".
3
Mountthemainmonitortothemountingbracket.
3-1 Lineupthetabonthebottomofthebracketwiththegrooveonthemainmonitor(
A
).
3-2 Lineupthetabonthetopofthebracketwiththegrooveonthemainmonitor,and
pushthemainmonitordownuntilitissecure(
B
).
Wall
1
Attachthemountingbrackettothewall
securely.
Installthemountingbracketon avertical
atwall.
A
RemovescrewAandthenremovethe
terminalcover.
B
LoosenscrewBandpushinthewiresof
theDCcabletotheterminalconnectors
(non-polar),thentightenthescrews.
Recommendedtorque:
0.8N·m{8.2k
g
f·cm}
C
Usethecablebinder(accessory)to
securetheDCcable(double-coated
area)tothemainmonitor.
D
Makesuretoreplacetheterminalcover.
HowtoconnecttheDCcable:
Whilepressingonthebuttonwithapoint-
edobjectsuchasascrewdriver,insert
thewireintotheterminalconnector.(To
disconnectawire,whilepressingonthe
button,pulloutthewire.)
Barewireattip
9mm
Terminal
Button
Wiringfrom
doorphone
Important:
Donotconnectthepowercable.
(Damagemayoccur.)
Howtomakewiringconnections:
Resetbutton
SDcard
slot
20cm
20cm
20cm
20cm
Cablebinder
(accessory)
12mm
Barewireattip
ScrewB
Forthefollowingreasons,leaveatleast20cmofspace
above,below,andtotheleftandrightsidesofthemain
monitor:
-Topreventmalfunctionandsoundcuttingout
-ToensureSDcardscanbeinsertedandremoved,
andtomakesuretheresetbuttoncanbeused
(theSDcardslotisonthesideofthemainmonitor;
theresetbuttonisonthebottom)
■
Abouttheinstallationpositionofthemainmonitorandmountingbracket
Placethemainmonitorinalocationthatyoureyesarethesameheightasthecentre
ofthedisplay.
Afterdecidingwheretoinstallthemainmonitor,attach
the mounting bracket in the location shown on the
right.
Doorphone installation position
Installingthepowersupplyunit
Imagerange:
Approx.900
Approx.500
Approx.85°
Approx.170°
Centre (default)
Imagerange:
Approx.900
Approx.85°
Right
Imagerange:
Approx.900
Approx.500
Approx.170°
Approx.85°
Approx.500
Approx.850
Approx.1,450
Approx.550
32mm
Whensettowide(default)
Centreof
doorphone
Centreof
doorphone
Centreof
doorphone
Approx.95°
Centreof
doorphone
Approx.1,450
Approx.500
Approx.900
Approx.170°
Approx.500
Approx.1,100
Approx.2,000
Imagerange
Imagedisplayedon
mainmonitor:
Viewwhenlooking
fromabove
Viewwhenlooking
fromabove
(Units:mm)
Notesaboutelectricalwiring
Makesurenottopinchthewires(asshowntothe
right)onthemountingbracketwheninstalling.
Donotforciblyattachtothemountingbracket.
Vertical,flatwall
Screws
(locallyprocured)
Holeinwall
83.5
60
7
50
Mountingbracket
(Units:mm)
(Units:mm)
(Units:mm)
(Units:mm)
  • Page 1 1
  • Page 2 2

Panasonic VLSWD501FX Operating instructions

Category
Door intercom systems
Type
Operating instructions
This manual is also suitable for

Panasonic VLSWD501FX is a wireless video intercom system that allows you to see and talk to visitors at your door from anywhere in your home. It comes with a main monitor and a doorphone, which can be installed either surface-mounted or flush-mounted. The system features a 3.5-inch color LCD screen, a built-in microphone and speaker, and the ability to connect to up to two doorphones and two additional monitors. It also has various functions such as door release, call transfer, and image recording.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI