Panasonic VLSWD501EX Operating instructions

Brand: Panasonic

Model: VLSWD501EX

Category: Door intercom systems

Type: Operating instructions

This manual is also suitable for

VLSWD501UEX

Panasonic VLSWD501EX is a wireless video intercom system that allows you to see and talk to visitors at your door from anywhere in your home. The system includes a door station that is installed outside your door and a main monitor station that is installed inside your home. The door station has a camera that provides a clear view of your visitor, and the main monitor station has a screen that displays the video feed from the door station. You can use the main monitor station to talk to your visitor and to unlock the door if you wish.

Installation Guide

Note to the installer

■ Beforeattemptingtoconnectoroperatethisproduct,pleasereadthelabelontherearof

themainmonitor.

■

Pleasereadthis

guide

carefully,andinstalltheproductsafelyandcorrectlybyfollowing

theinstructions.Carefullyreadtheinformationfoundinthesectiontitled"Foryoursafety"

inparticular.

■

Onlyuseattachments/accessoriesspecifiedbythemanufacturer.

■

Theinstallationshallbecarriedoutinaccordancewithallapplicableinstallationrules.

■

Panasonicassumesnoresponsibilityforinjuriesorpropertydamageresultingfromfailures

arisingoutofimproperinstallationoroperationinconsistentwiththisguide.Additionally,

anyresultingmalfunctionwillnotbecoveredunderthewarranty.

■ Afterinstallation,makesuretoleavethisguidewiththecustomer.

For the Installation of door station

and main monitor station

•VL-V554EXisasurfacemounttype,VL-V554UEX

isaushmounttype.

For your safety

Topreventsevereinjuryandlossoflife/property,readthissectioncarefullybeforeusingthe

producttoensureproperandsafeoperationofyourproduct.

WARNING

Preventingre,electricshockandshortcircuits

● Leaveinstallationworktothedealer.

Installationworkrequirestechniqueandexperiences.Failuretoobservethismay

causere,electricshock,injury,ordamagetotheproduct.Consultthedealer.

● Electricalconnectionworkshouldbeperformedbycertiedpersonnelonly.Certication

isrequiredforperformingelectricalconnectionwork.Consultyourdealer.

● Useonlythespeciedpowersupplyunit.

● Donotattempttodisassembleormodifythisproduct.Contactan authorisedservice

centreforrepairs.

● Neverinstallwiringduringalightningstorm.

● Donotconnectnon-specieddevices.

● Donotconnectapowercabletoaterminalthatisnotspeciedinthisguide.

● Whenopening holes in walls forinstallationorwiring, or when securingthepower

cable,makesureyoudonotdamageexistingwiringandductwork.

● Donotmakeanywiringconnectionswhenthepowersupplyisturnedon.

● Donotusethesuppliedpowersupplyunitforoutdoorinstallations(itisforindooruse

only).

● Donotinstallthemainmonitorandpowersupplyunitinthefollowingplaces:

- Placeswherethemainmonitorandpowersupplyunitmaybesplashedwithwateror

chemicals.



- Placeswherethereisahighconcentrationofdust,orhighhumidity.

● Donotperformanyactions(suchasfabricating,twisting,stretching,bundling,forcibly

bending,damaging,altering,exposingtoheatsources,orplacingheavyobjectsonthe

powercable) thatmaydamage thepowercable. Usingtheproduct withadamaged

powercable may causeelectricshock, shortcircuits,orfire. Contactanauthorised

servicecentreforrepairs.

● When existing chime wires are used, it is possible that they containAC voltage.

Contactanauthorisedservicecentre.

● Donot installoruse theproductinhealth carefacilitiesif anyregulationspostedin

theareainstructyounottodoso.Hospitalsor healthcare facilitiesmay be using

equipmentthatcouldbesensitivetoexternalRF(radiofrequency)energy.

● Do not install or use this product near automatically controlled devices such as

automaticdoors andfirealarms.Radio wavesemittedfrom this productmaycause

suchdevicestomalfunction,resultinginanaccident.

Preventingaccidentsandinjuries

CAUTION

● Ifthewiringisunderground,donotmakeanyconnectionsunderground.

● Ifthewiringisunderground,useaprotectiontube.

● Ifthewiringisoutdoors,useaprotectiontubeorasurgeprotector.

● Installtheproductsecurelyadheringto theinstructionsin thisguidetoprevent itfrom

fallingoffthewall.Avoidinstallingontolow-strengthwalls,suchasgypsumboard,ALC

(autoclavedlightweightconcrete),concreteblock,orveneer(lessthan18mmthick)walls.

Preventingelectricshock

Preventinginjury

1-62,4-chome,Minoshima,Hakata-ku,Fukuoka812-8531,Japan

©PanasonicSystemNetworksCo.,Ltd.2013

PNQW3982ZA PC1113MT1113

VL-V554EX/

VL-V554UEX

VL-MWD501EX

Doorstation Mainmonitorstation

Doorstationisdescribedas"doorphone"

andMainmonitorstationisdescribedas

"mainmonitor"inthisguide.

ModelNo.

VL-SWD501EX

VL-SWD501UEX

Wireless Video Intercom System

Toavoidmalfunctionorcommunicationdisturbances,donotinstallthedoorphoneorthemain

monitorinthefollowinglocations:

- Placeswherevibrationoranyotherkindofimpactoccurs.

- Placeswhereechoingisfrequent.

- Placesnearahighconcentrationofdust,hydrogensulphide,ammonia,sulphur,ornoxious

fumes.

■

For the doorphone

● Ifastronglightisshiningonthedoorphone,thevisitor’sfacemaynotbedistinguishable.Do

notplacethedoorphoneinthefollowinglocations:

- Wheremostofthebackgroundisthesky.

- Wherethebackgroundisawhitewall,anddirectsunlightwillreectoffit.

- Wheredirectsunlightwillshineonthedoorphone.

● Do not place the doorphone in locations where echoing occurs, as this will cause the

doorphonetobeepfrequently.

● Dustprotection/waterprotectionisIP54.

Onlywheninstallationworkspeciedinthisguideisproperlyperformedandappropriatewater

protectiontreatmentisperformed.

● Makesuretherearofthedoorphoneisnotsubjecttowater.

● Dependingontheinstallationlocation,condensationmayformonthedoorphone’slenscover.

Thismaycauseimagestobecomeobscured.Condensationwilldissipateasthetemperature

rises.

■

For the main monitor

● Installthe main monitor away fromelectronic appliances such as TVs, radios, personal

computers,air conditioners,boilercontrolpanels withintercom,home securityequipment,

wirelessdevices,ordigitalcordlessphones.

● Donotinstallthemainmonitorinplaceswhereitwillbeaffectedbyextremelyhigh-frequency

radiowaves (nearbroadcastingantennasetc.).Thismaycausethe displaytoickeroran

interruptingnoisetooccur.

● Leaveat least 20 cm of space above, below,and to the left and right sides ofthe main

monitor.Donotinstallonawallthatisdeeplyrecessed.

● Donotinstallthemainmonitorinsideawall.

● Besuretoinstallthemainmonitormorethan5mawayfromthedoorphone.

● The product operates in the frequency range of 1.88 GHz to 1.90 GHz, and the RF

transmissionpoweris 250 mW (max.).Refertothe "For best performance" sectioninthe

OperatingInstructions.

● Inareassurroundedbya highelectrical eld,disturbances mayoccurinthemainmonitor’s

imageorsound.

Supplied accessories for installation

■

For the doorphone

(EXonly)

Mounting

base×1

(UEXonly)

Flush

mounting

box

1

Screw×4(Usedwhen

installingthedoorphone)

(EX



:4mmx12mm)

(UEX:4mmx25mm)

Nameplate×2

(incl.1spare)

Hexwrench×1

■

For the main monitor



Mounting

bracket×1

Cablebinder×1

■ Power supply unit and related items



Powersupply

unit×1

(PartNo.VL-PS240)

Cablebinder×2

Important:

● You will need the following additional items to install and congure the doorphone

and the main monitor.

[Locally procured]

- Screws(formountingbase:×2,formountingbracket:×2):

Preparethescrews(

thedrawingontheright)accordingto

thematerial,structure,strengthandotherfactorsofthemounting

areaandthetotalweightofobjectstobemounted.

- Powercables(AC/DCcables),wires(fordoorphoneandotherconnections):

Preparecablesandwiresoftheappropriatespecication.(

"Wiretypeandlength")

Note:

● Theillustrationsinthesuppliedmanual(s)mayvaryslightlyfromtheactualproduct.

4mm

Precautions for installation

Wiring schematic diagram

Setupcorrectlyaccordingtothefollowingwiringschematicdiagramand"Wiretypeandlength".

● Forinformation,suchasordernumbers,aboutoptionaldevicesthatcanbeconnectedto,refertothe"Additional/replacementaccessories"sectionintheOperatingInstructions.

ブ

プ

MAIN MONITOR

DOORPHONE 1

DOORPHONE 2

POWER SUPPLY UNIT

220-240VAC

Connectiondeviceforoptionoutput(Acontact)

*1MakesuretoonlyconnectelectricvehiclegatelockstotheS3/S4terminalsofthe

doorphones.

*2MakesuretoonlyconnectelectricdoorlockstotheS1/S2terminalsofthedoorphones.

NP: Non-polarised

Power

supply

Power

supply

Power

supply

Power

supply

12VAC/DC

Electriclock

(Electricvehicle

gatelock)

Electriclock

(Electricdoor

lock)

Electriclock

(Electricdoor

lock)

Electriclock

(Electricvehicle

gatelock)

24VDC

Wire type and length

Wiringrun

Wiretype

Diameter Length(Max.)

Mainmonitor–

Doorphone

φ0.65mm 22AWG 100m

φ1.0mm 18AWG 130m

φ0.5mm CAT5 50m

Mainmonitor–

Powersupplyunit

φ0.65mm 22AWG 10m

φ1.0mm 18AWG 20m

Powersupplyunit–

ACpowersource

φ1.2mm-φ2.0mm

(17AWG-12AWG)

Norequirement

Doorphone–

Electriclock

φ0.5mm-φ1.2mm

(24AWG-17AWG)

Accordingtospeci-

cationofconnected

device.

Mainmonitor–

Connectiondeviceforoption

output(Acontact)

φ0.5mm-φ1.2mm

(24AWG-17AWG)

Accordingtospeci-

cationofconnected

device.

*1Type:Single-paircablewithoutersheath(jacket)

Conductor:Coppersolid

● Acertiedpowersupplywiringhastobeusedwiththisequipment.Therelevantnational

installationand/orequipmentregulationsshallbeconsidered.Acertiedpowersupplywiring

notlighterthanordinarypolyvinylchlorideexiblewiringaccordingtoIEC60227shallbeused.

*2Whenusinganelectriclockoraconnectiondeviceforoptionoutput(Acontact),selectadevice

thatmeetsthefollowingguidelines:

● Electriclockconnectionterminal(S1/S2,S3/S4):

- N/Odryclosurecontact

- 12VAC/DC,lessthan1A

● Connectiondeviceforoptionoutput(Acontact)terminal(OUT1/OUT2):

- 24VAC/DC,lessthan0.3A(minimumcontact:5VDC1mA)

A D

ScrewA

Youcanusethe[Wide/Zoomsettings]settingonthemainmonitortoselecttheareathat

isvisiblewhenavisitorcalls;availablesettingsare[Wide],[Zoom],and[All](entireimage

display).(Defaultsetting:[Wide])

● Thefollowingvaluesareforwhenthedoorphoneisinstalledinthestandardposition(thecentre

ofthe doorphone’sheight isapproximately1,450mm)and at a distance ofapproximately

500mmfromthecameralens.

■ Installation height and area visible by the camera lens

When set to zoom

Displaysaportionofthewideimageat2timesthesize.

● Because a digital zoom is used, the image quality of zoom

displayislowerthanthatofwidedisplayorentireimagedisplay.

Imagedisplayedon

mainmonitor:

● You canusethemainmonitor’s[Zoomposition settings]settingtoselectthedesiredarea

visiblewhenzooming.

Refertothefollowingandcongurethemainmonitor.

Entire image display

Theareaaboveandbelowthewideimageisvisible.

Important:

● Onthebottomsurfaceofthedoorphoneandthemountingbase,thereareholestoallowwater

todrain.Donotcoverthemupwheninstalling.

● Whenexistingwiring(suchaschimewires)isused:

- ItmaycontainACvoltagethatmaycauseelectricshockand/ordamagetheproduct.

- Neverusethefollowingtypesofwiring.Consultaqualiedtechnician/dealer.

VL-V554EX VL-V554UEX

Attachthemountingbasetothewallsecurely.

Mountingbase

(accessory)

Wire(locallyprocured)

Wall

83.5mm

Screws(locallyprocured)×2

● Installthemountingbaseonaverticalatwall.

Installtheflushmountingboxinthe

wall.

Flushmountingbox(accessory)

100mm

Knockouthole

151mm

37mm

*1Onlyopentheknockoutholesas

requiredforthewiring.

Useahexwrench(accessory)toloosenscrewAandremovethefrontpanelofthedoor-

phone.



ScrewA

Frontpanel

2mmhexwrench

(accessory)

Connectthewires.

Terminalforthe

mainmonitor

<Rear

view>

Terminalsfortheelectriclocks

● Recommendedtorque:

0.5N·m{5.1k

f·cm}

● Maximumtorque:

0.7N·m{7.1k

f·cm}

3-1Loosenthescrews.

3-2Pushinthewirestotheterminalconnectors(non-polar),thentightenthescrews.

Attachthedoorphonetothemounting

base.

Screws(accessory)×4

Attachthedoorphonetotheflushmounting

box.



Screws(accessory)×4

AttachthenameplatetothedoorphoneandusescrewAtosecurethefrontpanel.

● Writethenameonthenameplateasneeded.

Nameplate

(accessory)

ScrewA

● Recommendedtorque:

0.35N·m{3.6k

f·cm}

Approx.500

Approx.170°

Approx.2,250

Imagerange

Approx.115°

Approx.500

Imagedisplayedon

mainmonitor:

Approx.1,600

Approx.650

Approx.1,450

Upanddown

Leftandright(whenlookingfromabove)

Imagerange

Approx.2,050

Approx.500

Centreof

doorphone

Approx.45°

Centre (default)

Approx.45°

Approx.500

Imagerange

Approx.1,650

Down

Approx.45°

Approx.500

Approx.1,400

Imagerange

Left

Approx.1,500

Approx.1,450

Approx.550

Approx.1,450

Approx.1,250

Approx.400

Installing the doorphone

■

About the installation location

● Thedevicemustbeinstalledinsideanelectricalpanelorcabinet.

● Areadilyaccessibledisconnectdeviceshallbeincorporatedexternaltotheequipment.

- Externaldisconnectdevicemustbecertiedandhaveacreepageandclearancedistance

of3mmormore.

■

Precautions for wiring

● Makesureyouturnoffthepoweratthebreakerbeforeperforminganywiringwork.

● Always connectAC or DC cables to the appropriate connection terminals. Incorrectly

connectingtheACorDCcablesmaydamagethepowersupplyunit.

● Topreventthepower cablesfromdisconnectingandto preventelectric shock,secure the

powercablesusingthecablebinders(accessory)andattachthecablecovers.

How to connect the power cable (AC/DC)

StriptheAC/DCcablesasfollows:

7mm

45mm

<ACcable>

<DCcable>

25mm

7mm

Removethescrews(

)andthenremove

thecablecovers(

ConnecttheAC/DCcabletotheACIN

terminal/DCOUTterminalonthetopand

bottomofthepowersupplyunit,andthen

securethewiresbytighteningthescrews.

● Recommendedtorque:

- ACterminal:0.4N·m{4.1k

f·cm}

- DCterminal:0.45N·m{4.6k

f·cm}

<Frontview>

ACcable

DCcable

Screws

Cablebinders(accessory)

Usethecablebinders(accessory)to

securetheAC/DCcables(double-coated

area)tothepowersupplyunit.

Makesuretoreplacethecablecovers(

Connectthepowersupplyunit(accessory)andAC/DCcables(locallyprocured).

CAUTION

Insertthecablesfirmlyalltheway

intotheterminals.

Ifthecablesarenotinsertedall

theway,heatmaybegenerated.

*1 Makesurethattherearenobarewires

exposedoutsidetheproduct.

Screws(

)

Cablecovers(

)

DCOUTterminal

ACcable

binderhole

ACINterminal

<Topview>

<Bottomview>

DCcable

binderhole

Power supply unit (with cable covers

removed)

Attach to the DIN rail

Attachintheorderdescribedbelowsothathook(b)ispositionedatthebottom.

Hanghook(a)ontheDINrail(

Pullandholdtheleverdown(

Securehook(b)totheDINrail(

Hook(a)

Hook(b)

Main monitor installation position

Installing the main monitor

Mainmonitor

installationposition

82.5mm

82.7mm

ConnecttheDCcableandwires.

● Connectthewires correctly according to "Wiring schematic

diagram".

Mountthemainmonitortothemountingbracket.

3-1 Lineupthetabonthebottomofthebracketwiththegrooveonthemainmonitor(

3-2 Lineupthetabonthetopofthebracketwiththegrooveonthemainmonitor,and

pushthemainmonitordownuntilitissecure(

Wall

Attachthemountingbrackettothewall

securely.

● Installthemountingbracketona vertical

atwall.

A

RemovescrewAandthenremovethe

terminalcover.

 LoosenscrewBandpushinthewiresof

theDCcabletotheterminalconnectors

(non-polar),thentightenthescrews.

● Recommendedtorque:

0.8N·m{8.2k

f·cm}

C

Usethecablebinder(accessory)to

securetheDCcable(double-coated

area)tothemainmonitor.

 Makesuretoreplacetheterminalcover.

How to connect the DC cable:

Whilepressingonthebuttonwithapoint-

edobjectsuchasascrewdriver,insert

thewireintotheterminalconnector.(To

disconnectawire,whilepressingonthe

button,pulloutthewire.)

Barewireattip

9mm

Terminal

Button

Wiringfrom

doorphone

Important:

Donotconnectthepowercable.

(Damagemayoccur.)

How to make wiring connections:

Resetbutton

SDcard

slot

20cm

Cablebinder

(accessory)

12mm

Barewireattip

ScrewB

● Forthefollowingreasons,leaveatleast20cmofspace

above,below,andtotheleftandrightsidesofthemain

monitor:

-Topreventmalfunctionandsoundcuttingout

-To ensureSDcardscanbeinsertedandremoved,

andtomakesuretheresetbuttoncanbeused

(theSDcardslotisonthesideofthemainmonitor;

theresetbuttonisonthebottom)

■

About the installation position of the main monitor and mounting bracket

● Placethemainmonitorinalocationthatyoureyesarethesameheightasthecentre

ofthedisplay.

● Afterdecidingwheretoinstallthemainmonitor,attach

the mounting bracket in thelocationshown on the

right.

Doorphone installation position

Installing the power supply unit

Imagerange:

Approx.900

Approx.500

Approx.85°

Approx.170°

Centre (default)

Imagerange:

Approx.900

Approx.85°

Right

Imagerange:

Approx.900

Approx.500

Approx.170°

Approx.85°

Approx.500

Approx.850

Approx.1,450

Approx.550

32mm

When set to wide (default)

Centreof

doorphone

Centreof

doorphone

Centreof

doorphone

Approx.95°

Centreof

doorphone

Approx.1,450

Approx.500

Approx.900

Approx.170°

Approx.500

Approx.1,100

Approx.2,000

Imagerange

Imagedisplayedon

mainmonitor:

Viewwhenlooking

fromabove

Viewwhenlooking

fromabove

(Units:mm)

Notes about electrical wiring

Makesurenottopinchthewires(asshowntothe

right)onthemountingbracketwheninstalling.

● Donotforciblyattachtothemountingbracket.

Vertical,flatwall

Screws

(locallyprocured)

Holeinwall

83.5

Mountingbracket

(Units:mm)

Panasonic VLSWD501EX Operating instructions

Brand: Panasonic

Model: VLSWD501EX

Category: Door intercom systems

Type: Operating instructions

This manual is also suitable for

VLSWD501UEX

Download PDF

report

Panasonic VLSWD501EX Operating instructions

This manual is also suitable for

Panasonic VLSWD501EX Operating instructions

Related papers

Other documents