Xanté Impressia Digital Multi Media Press Owner's manual

Xanté
Brand
Xanté
Model
Impressia Digital Multi Media Press
Category
Toners & Laser Cartridges
Type
Owner's manual
©2012 Xanté Corporation. Xanté, the Xanté logo and Impressia are registered trademarks of Xanté Corporation.
Page
1 of 3
DMMP Setup / Installation
IMP DMMP Setup Rev 3.pdf
Nov 12, 2012 - DSO
Unbox printer stand
Unbox the printer stand and set
upright. Place the stand where the
feeder system will be located. Lock
all wheels in place by pressing the
locks down.
Use foot to lock all
wheels in place
Unbox printer
Remove the 4 plastic box cover
caps. Lift the box straight up. Re-
move the plastic and locate the 4
lift handles. Lift the printer by using
the handles and place on the stand.
Printer positioning
Slide the printer into the slotted rail
on the left side of the stand. Insert
the 2 alignment screws from under-
neath the stand’s table top and into
the bottom of the printer.
The printer will
stop at the edge
Alignment Screw Alignment Screw
Page 2 of 3
Install stand wings
Install both side wings on the stand
by aligning the side notches with
the 4 screws located on both ends
of the stand.
Remove Pack Tape
Remove all packaging tape from
the printer and its trays.
Unbox
/
Install Feeder
Unbox the feeder and place it on
the right side of the printer stand.
Slide the feeder into the open slot
on the printer. Screw the locking
knob in place.
Locking KnobVerify alignment
Slide the right side media guide un-
der the alignment rail and position
the guide against the media block.
Secure 2 allen screws to the block.
Repeat for the left side. Then install
the media back stop by inserting
the nut under the slotted rail and
tighten down the thumb screw.
Right side
Left side
Screws
Right side
Left side
Right side
Screws
Screws
Thumb Screw
Thumb Screw & Nut
Locate the 4 thumb screws for the
optional conveyor tray. Place the
tray into position on the left side
and secure all four screws. Place
the optional conveyor on top of the
printer and slide it into position.
Secure the 2 locking knobs on the
bottom of the conveyor tray.
Locate the single small at screw.
Secure the screw into the front right
side of the alignment arm on the
front of the printer.
Screws
Unbox
/
Install Optional Conveyor
Locking Knob
Locking Knob
Left side
Right side
Screws
Page 3 of 3
Unbox
/
Install Toners
Unbox all 4 color toners. Before in-
serting the toner, shake each toner
container up and down 5 to 6 times
to ensure even distribution of toner
within the cartridge.
With the toner label facing up, in-
sert the toner into place, keeping
the container horizontal. Repeat
the same procedure for all 4 toner
cartridges.
Power & Communication
Plug in the optional conveyor power to
the right side port on the feeder. Plug
the feeder power to the left side port.
Plug in the
ethernet
and power
cable.
Conveyor
Ethernet
Feeder
Power
Removing Paper Stacker Cover
If the printer was shipped with the paper
stacker cover installed and the optional
conveyor is going to used, the cover must
be removed. Lift the handle and compress
the center release tabs to lift off the printer.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Xanté Impressia Digital Multi Media Press Owner's manual

Xanté
Brand
Xanté
Model
Impressia Digital Multi Media Press
Category
Toners & Laser Cartridges
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents