Vivotek PZ7122 Quick Installation Manual

Vivotek
Brand
Vivotek
Model
PZ7122
Category
Security cameras
Type
Quick Installation Manual

This manual is also suitable for

P/N: 625006701G Ver.1.1
EN - 1
English
Contact your distributor when such
cases happen.
Keep the Network Camera away
from water. If the Network Camera
is wet, power off immediately.
Refer to your user's manual for the
operating temperature.
Power off the Network Camera
as soon as it is found smoking or
smelt unusual.
Do not place the Network Camera
around the heat sources, such as
television or oven.
Keep the Network Camera away
from direct sunlight.
Do not place the Network Camera
in high humid environments.
Activity
Power/MIC
Activity
Power/MIC
Activity
Power/MIC
Activity
Power/MIC
Contact your distributor when such
cases happen.
Warning Before Install
EN - 2
Do not place the Network Camera
on unsteady surfaces.
Do not touch the Network Camera
when it's lightening.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert any object into the
Network Camera, such as needles.
Activity
Power/MIC
Activity
Power/MIC
Activity
Power/MIC
Activity
Power/MIC
Activity
Power/MIC
Do not manually pan and tilt the
Network Camera when the power is
on.
Activity
Power/MIC
EN - 3
English
Antenna
(PZ7112 / PZ7122 only)
Screws
PZ7111 / PZ7121/
PZ7112 / PZ7122
A/V cable
Power adapter
Quick installation guide /
Warranty card
Software CD
Activity
Power/MIC
Ceiling mount brackets
Package Contents
1
EN - 4
Front panel
Back panel
Activity
Power/MIC
Built-in microphone
Status LED
Lens
Indented reset button
Ethernet 10/100
RJ45 socket
External/Internal
microphone switch
General I/O
terminal block
AV out
Microphone in
Power cord socket
Antenna
(PZ7112 / PZ7122 only)
Physical Description
2
ee
AV
EN - 5
English
2
Mounting the Network Camera
1. Attach ceiling mount bracket A to the Network Camera and secure it with two
small screws.
2. Drill three pilot holes into the ceiling; hammer the plastic anchors into the
holes.
3. Fasten ceiling mount bracket B to the ceiling with three screws.
4. Slide the Network Camera into ceiling mount bracket B.
5. Secure ceiling mount bracket A and B with a small screw.
2
3
4
1
A B
5
Hardware Installation
3
EN - 6
General Connection (without PoE)
1. If you have external devices such as sensors and alarms, make connections from gen-
eral I/O terminal block.
2. Connect the camera to a switch via a Ethernet cable.
3. Connect the supplied power cable from the camera to a power outlet.
ee
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
AV
2
3
Ethernet switch
Network Deployment
4
1: Power
2: Digital output
3: Digital input
4: Ground
1
EN - 7
English
Power over Ethernet (PoE)
ee
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
AV
PoE switch
ee
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
AV
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the camera and a non-PoE
switch.
PoE power injector
(optional)
When using a PoE-enabled switch
The camera is PoE-compliant, allowing transmission of power and data via single Ether-
net cable. See the following illustration to connect the camera to a PoE-enabled switch
via Ethernet cable.
non-PoE switch
EN - 8
0002D10766AD
RoHS
Network Camera
PZ7112
1. Install the "Installation Wizard 2" under the Software Utility directory from software CD.
2. The program will conduct analyses on your network environment. After your network is
analyzed, please click on the "Next" button to continue the program.
3. The program will search the VIVOTEK Network Devices in the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the bottom of your device to connect the Internet Explorer to the
Network Camera.
0002D10766AD
172.16.7.13 PZ71X2
Installation
Wizard 2
IW
2
Assigning IP Address
5
EN - 9
English
For further setup, please refer to user's manual on the software CD.
Ready to Use
6
1. Access to the Network Camera from the Internet.
2. Retrieve live video through web browsers or recording software.
EN - 10
1. Check the SSID currently set on your wireless access point (AP).
2. Go to PZ7112 / PZ7122's Configuration > Advanced mode > Wireless.
3. Type in the SSID consistent with the setting on your AP.
4. Select the Wireless mode as "Infrastructure".
5. Click Save. The Network Camera starts to reboot.
Note
1. SSID, abbreviated from Service Set Identifier, is the name assigned to the wireless
network. The PZ7112 / PZ7122's factory SSID setting is set to "default".
2. Select "Ad-Hoc" wireless mode if you want the PZ7112 / PZ7122 to communicate
without using an AP or wireless router.
ee
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
ADSL/Cable/Hub
AP
AV Out
For further setup, please refer to user's manual on the software CD.
Configure the Wireless Connection (PZ7112 / PZ7122 only)
7
PZ7112 / PZ7122
6. Wait for the live image is reloaded to your browser. Then, unplug the power cable and
Ethernet cable from the Network Camera.
7. Replug the power cable to the camera. The Network Camera now operates in wireless
mode.
P/N: 625006701G Ver.1.1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Vivotek PZ7122 Quick Installation Manual

Vivotek
Brand
Vivotek
Model
PZ7122
Category
Security cameras
Type
Quick Installation Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents