Vivotek PT8133W Quick Installation Manual

PT8133W
Vivotek
Brand
Vivotek
Model
PT8133W
Category
Security cameras
Type
Quick Installation Manual

This manual is also suitable for

Vivotek PT8133W is an advanced network camera with 1MP resolution, wireless connectivity, and Power over Ethernet (PoE) capability. With built-in Wi-Fi and support for WPS (Wi-Fi Protected Setup), the camera can be easily connected to a wireless network. The PoE feature allows for easy installation with a single cable providing both power and data.

Vivotek PT8133W is an advanced network camera with 1MP resolution, wireless connectivity, and Power over Ethernet (PoE) capability. With built-in Wi-Fi and support for WPS (Wi-Fi Protected Setup), the camera can be easily connected to a wireless network. The PoE feature allows for easy installation with a single cable providing both power and data.

Quick Installation Guide
PT8133/33W
1MP • PoE
1MP • WPS • 802.11n
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
All specications are subject to change without notice. Copyright 2011 VIVOTEK INC. All rights reserved. P/N:625016400G
c
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T: +886-2-82455282|F: +886-2-82455532|E: [email protected]
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686|F: 408-773-8298|E: [email protected]
PT8133:
PT8133W:
EN - 1
English
Contact your distributor in the event of
occurrence.
Keep the Network Camera
away from water. If the Network
Camera becomes wet, power off
immediately.
Refer to your user’s manual for the
operating temperature.
Power off the Network Camera as
soon as smoke or unusual odors
are detected.
Do not place the Network Camera
around heat sources, such as a
television or oven.
Keep the Network Camera away
from direct sunlight.
Do not place the Network Camera
in high humidity environments.
Contact your distributor in the event of
occurrence.
Warning Before Installation
EN - 2
Do not place the Network Camera
on unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
Do not manually pan and tilt the
Network Camera when the power is
on.
EN - 3
English
5
0
0
0
2
4
7
0
1
G
Antenna
(PT8133W Only)
Screws
PT8133/33W Power Adapter
Quick Installation Guide /
Warranty Card
Software CD
Mount kit & Foot Pads
Package Contents
1
EN - 4
Front Panel
Back Panel
Antenna
Status LEDs
Lens and Manual
Focus Ring
Ethernet 10/100
RJ45 Socket Power cord socket
Physical Description
2
ETHERNET 12V
1.5A
WPS
WPS button (PT8133W)
Recessed Reset
Button
Item LED status Description
LED Denitions
1 Steady Red Power on and system boot
Red LED off Power off
2 Blink Green every 1 sec. + Steady Red Network connected (heartbeat)
Green LED off + Steady Red Network failed
3 Blink Red every 0.15 sec. + Blink Green every 1 sec. Upgrading rmware
4 Blink Red every 0.15 sec. + Blink Green every 0.15 sec. Restoring defaults
5 Steady Blue Linked to a wireless AP
Blue LED off Not connected to wireless network
6 Blink Blue every 0.15 sec. WPS searching
EN - 5
English
Mounting the Network Camera - Ceiling Mount
1. Use the holes on the mount bracket as a template to mark where holes will be drilled
on the ceiling. Drill two holes into the ceiling; and hammer in the plastic anchors.
2. Attach the Network Camera to the mount bracket using two athead screws.
3. Secure mount bracket to the ceiling using two panhead screws.
4. You can now proceed with cabling.
Hardware Installation
3
If you prefer wireless conguration, you
can congure wireless connection before
you mount the camera to bracket.
NOTE:
EN - 6
2
Mounting the Network Camera - Wall Mount
1. Use the holes on the mount bracket as a template to mark where holes will be drilled
on the ceiling. Drill two holes into the wall; and hammer in the plastic anchors.
2. Secure mount bracket to the wall using two included panhead screws.
3. Attach the Network Camera to the mount bracket using two athead screws.
4. You can now proceed with cabling.
If you prefer wireless conguration, you
can congure wireless connection before
you mount the camera to bracket.
NOTE:
EN - 7
English
General Connection (without PoE)
1. Connect the camera to a switch via Ethernet cable.
2. Connect the supplied power adapter between the camera and a power outlet.
Network Deployment
4
12V
1.5A
ETHERNET
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
2
Ethernet Switch
1
NOTE:
The PT8133W comes with an antenna. It should be installed by turning clockwise to
attach to the associated connector. The wireless model, PT8133W, does not support
PoE.
EN - 8
Power over Ethernet (PoE)
12V
1.5A
ETHERNET
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
PoE switch
12V
1.5A
ETHERNET
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.
PoE Power Injector
(optional)
When using a PoE-enabled switch
The PT8133 Network Camera is PoE-compliant, allowing transmission of power and
data via a single Ethernet cable. Follow the below illustration to connect the camera to a
PoE enabled switch via a CAT5e Ethernet cable.
Non-PoE Switch
EN - 9
English
0002D10766AD
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is
analyzed, please click on the “Next” button to continue the program.
0002D10766AD
172.16.7.13 PZ71X2
PZ81X1
Installation
Wizard 2
IW
2
Assigning an IP Address
5
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After a brief search, the main installer window will pop up. Double-click on the MAC
address that matches the one printed on the camera label or the S/N number on the
package box label to open a browser management session with the Network Camera.
EN - 10
For further setup, please refer to the user's manual on the software CD.
Wireless Mega-Pixel Network Camera
Ready to Use
6
1. A browser session with the Network Camera should prompt as shown below.
2. You should be able to see live video from your camera. You may also install the
32-channel recording software from the software CD in a deployment consisting of
multiple cameras. For its installation details, please refer to its related documents.
EN - 11
English
Congure the Wireless Connection (PT8133W)
7
1. Make sure your AP (Access Point) and Operating System support the WPS (Wi-Fi
Protected Setup) functions. WPS enables easy setup with compatible APs.
4. Wait for 2 minutes with the onscreen progress bar. The camera should then reboot.
When the progress bar disappears, disconnect your LAN cable. You can refresh or
re-start your web console to see live video.
When WPS conguration is done, wireless connectivity will be established and the
security encryption, such as WEP or WPA-PSK, will be synchronized with the AP.
Use the IW2 utility to nd the camera. As for IP setting, the camera's use of DHCP
or static IP is determined by your conguration on the network camera via the web
console. The camera's default is DHCP.
ADSL/Cable/Hub
12V
1.5A
ETHERNET
WPS
PT8133W
Wireless AP WPS buttons
2. Connect your camera using a LAN cable, open a web console, and enter the
Conguration -> Wireless page. Select the WPS checkbox, and click the Save
button.
3. The camera's blue LED should start ashing. Press and hold down both of the
WPS buttons on your AP and your camera for at least 1 second. (Some router/
AP will have a virtual button on their management software instead.) Refer to your
AP's documentation for details using its WPS function.
EN - 12
NOTE:
1. WPS may not work if your AP is congured with a "hidden" SSID.
2. If the camera can not detect an AP after 2 minutes, the wireless setup will be
cancelled.
3. If a camera is assigned with a xed IP outside the AP's network segment, wireless
setup will fail.
4. A wired connection always has a higher priority. Unplug the LAN cable at an
appropriate time for the wireless setup to take effect.
5. The camera also supports manual conguration of wireless settings, enter the
SSID (Service Set Identier) and security authentication password in a web
console with the camera.
5-1. Enter the Conguration page -> Wireless.
5-2. Enter the SSID and password of your AP, select the Wireless mode as
"Infrastructure."
5-3. Use the "ping <IP address> -t" command in a DOS prompt to observe wired
connectivity. Click the Save button. When wired connection is discontinued,
unplug the LAN cable.
5-4. After several seconds, the camera will switch to wireless connection.
Disconnect and then connect the power cord to restart the camera, and you
should be able to see live video from the web console.
6. Select "Ad-Hoc" wireless mode if you prefer direct connection with a PC without the
intermediate AP or wireless router.
Quick Installation Guide
PT8133/33W
1MP • PoE
1MP • WPS • 802.11n
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
All specications are subject to change without notice. Copyright 2011 VIVOTEK INC. All rights reserved. P/N:625016400G
c
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T: +886-2-82455282|F: +886-2-82455532|E: [email protected]
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686|F: 408-773-8298|E: [email protected]
PT8133:
PT8133W:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Vivotek PT8133W Quick Installation Manual

PT8133W
Vivotek
Brand
Vivotek
Model
PT8133W
Category
Security cameras
Type
Quick Installation Manual
This manual is also suitable for

Vivotek PT8133W is an advanced network camera with 1MP resolution, wireless connectivity, and Power over Ethernet (PoE) capability. With built-in Wi-Fi and support for WPS (Wi-Fi Protected Setup), the camera can be easily connected to a wireless network. The PoE feature allows for easy installation with a single cable providing both power and data.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents