2. Vivotek
  3. IP7151
IP7151

Vivotek IP7151 Quick Installation Manual

  • Hello! I am an AI chatbot trained to assist you with the Vivotek IP7151 Quick Installation Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
EN - 1
English
Contact your distributor when such
cases happen.
Keep the Network Camera away
from water. If the Network Camera
is wet, power off immediately.
Refer to your user's manual for the
operating temperature.
Power off the Network Camera
as soon as it is found smoking or
smelt unusual.
Do not place the Network Camera
around the heat sources, such as
television or oven.
Keep the Network Camera away
from direct sunlight. Do not place the Network Camera
in high humid environments.
Contact your distributor when such
cases happen.
Warning Before Install
IP7151_7152_QIG.indd 1 2007/9/19 上午 09:34:40
EN - 2
Do not place the Network Camera
on unsteady surfaces. Do not touch the Network Camera
when it's lightening.
Do not disassemble the Network
Camera. Do not drop the Network Camera.
Do not insert any object into the
Network Camera, such as needles.
IP7151_7152_QIG.indd 2 2007/9/19 上午 09:34:42
EN - 3
English
Camera stand
Lens
IP7151 / IP7152
Warranty card
Power adapter
Software CD
1
Check Package Contents
Antenna (IP7152 only)
EN - 4
Power cord socket
Ethernet 10/100
RJ45 socket
Indented reset button
General I/O
terminal block
Audio out
MIC in
External/Internal
MIC switch
Front panel
Back panel
Lens
Focus controller
Zoom controller
2Physical Description
Built-in MIC
Light sensor
Status LED
Antenna
(IP7152 only)
Antenna
(IP7152 only)
IP7151_7152_QIG.indd 4 2007/9/19 上午 09:34:48
EN - 5
English
Indented reset button
For further setup, please refer to the lens' instruction manual inside the
lens package.
1. Mount the lens by turning it clockwise onto the camera mount until it stops. If
necessary, turn the lens counterclockwise slowly until it gets the best attitude.
2. Connect the lens cable plug to the camera connector.
3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten
the zoom controller.
4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten
the focus controller.
W
∞
N
T
1
2
4
3
3Mounting the Lens to the Camera
IP7151_7152_QIG.indd 5 2007/9/19 上午 09:34:49
EN - 6
General Connection (without PoE)
General Connection (without PoE)
1
. Connect the camera to a hub via Ethernet cable.
2
. Connect the supplied power cable from the camera to a power outlet.
POWER COLLISION
LINK
RECEIV E
PARTITION
12345
1
2
Ethernet hub
4
Network Deployment
EN -
7
English
Power over Ethernet (PoE) (IP7151 only)
Power over Ethernet (PoE) (IP7151 only)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
PoE hub
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
When using a non-PoE hub
Use a PoE power injector (optional) to connect between the camera and a non-
PoE hub.
non-PoE hub
PoE power injector
(optional)
When using a PoE-enabled hub
The camera is PoE-compliant, allowing transmission of power and data via single
Ethernet cable. See the following illustration to connect the camera to a PoE-
enabled hub via Ethernet cable.
EN - 8
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
RoHS
Network Camera
Model No:IP7151
Pat. 6,930,709 Made inTaiwan
MAC:0002D1070417
1. Run the "Installation Wizard 2" under the Software Utility directory from software
CD.
2. The program will conduct analyses on your network environment. After your
network is analyzed, please click on the "Next" button to continue the program.
3. The program will search the Vivotek Video Receivers, Video Servers or Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that
matches the one labeled on the bottom of your device to connect the Internet
Explorer to the Network Camera.
00-02-D1-07-04-17 192.168.0.219 IP7151
Installation
Wizard 2
5Assigning IP Address
0002D1070417
IP7151_7152_QIG.indd 8 2007/9/19 上午 09:34:52
EN - 9
English
For further setup, please refer to user's manual on the software CD.
6Retrieving Images
IP7151_7152_QIG.indd 9 2007/9/19 上午 09:34:52
EN -
1
0
7
Congure the Wireless Connection
(IP7152 only)
1
. Check the SSID currently set on your wireless access point (AP).
2. Go to IP7152's Conguration > Wireless LAN.
Note:
1.SSID, abbreviated from Service Set Identier, is the name assigned to the wireless
network.
The IP7
1
5
2
's factory SSID setting is set to "default".
2
.Select "Ad-Hoc" wireless mode if you want the IP7
1
5
2
to communicate without
using an AP or wireless router.
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
ADSL/Cable/Hub
AP
3
. Type in the SSID consistent
with the setting on your AP.
4
. Select the Wireless mode as
"Infrastructure".
5. Click Save.
For further setup, please refer to user's manual on the software CD.
/