2. Toro
  3. Light Kit, MB TX 2500 Tracked Mud Buggy

Toro Light Kit, MB TX 2500 Tracked Mud Buggy Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Light Kit, MB TX 2500 Tracked Mud Buggy Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FormNo.3413-686RevA
LightKit
MBTX2500TrackedMudBuggy
ModelNo.137-0558
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Nopartsrequired
–
Preparethemachine.
2
Nopartsrequired
–
Drilltheholes.
Bracket2
Carriagebolt(5/16x1inch)
4
Nut(5/16inch)
4
Switch
1
Wireharness1
Lightassembly2
Frictionwasher2
Grommet
2
3
Cabletie
2
Installthelights.
4
Nopartsrequired
–
Completetheinstallation.
©2017—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3413-686*A
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface,engagetheparking
brake,andlowerthehopper.
2.Shutofftheengineandremovethekey.
3.Disconnectthenegative(-)cablefromthebattery.
4.Removethefueltank;refertotheOperator’sManualfor
themachine.
2
DrillingtheHoles
NoPartsRequired
Procedure
Onbothsidesofthemachine,drillaholeintotheframe
(0.828inchdiameter)inthelocationshowninFigure1.
g204754
Figure1
1.7.4cm(2.9inches)3.7.6cm(3inches)
2.Hole(0.828inch)
3
InstallingtheLights
Partsneededforthisprocedure:
2Bracket
4
Carriagebolt(5/16x1inch)
4
Nut(5/16inch)
1
Switch
1Wireharness
2Lightassembly
2Frictionwasher
2
Grommet
2
Cabletie
Procedure
1.Onbothsidesofthemachine,installabracketusing2
carriagebolts(5/16x1inch)and2nuts(5/16inch)as
showninFigure2.
g204781
Figure2
1.Nut—5/16inch(2)3.Carriagebolt—5/16x1
inch(2)
2.Bracket
2
2.Removethebolt,lockwasher,andnutfromalight
assembly.Usethehardwareandafrictionwasher
tosecurethelighttoabracket(Figure3).Donot
overtightenthefasteners.Repeatfortheothersideof
themachine.
g204816
Figure3
1.Bolt4.Bracket
2.Light5.Lockwasher
3.Frictionwasher6.Nut
3.Removeanddiscardtheknockoutfromthetower
panel(Figure4).
Note:Theknockoutiscoveredbytheconsoledecal.
g204765
Figure4
1.Knockout
4.Frominsidethemachine,pushtheswitchconnector
ofthewireharnessthroughtheknockoutholeand
connectittotheswitch(Figure5).
g204812
Figure5
1.Switchconnectorofwire
harness
2.Switch
5.Installtheswitchintheknockouthole(Figure5).
6.Pushtherightlightconnectorthroughtheholeyou
drilledontherightsideofthemachine.Slidea
grommetovertheconnector,downthewireharness,
andsecureitinthehole(Figure6).Repeatfortheleft
wireharnessconnectorontheleftsideofthemachine.
g204815
Figure6
1.Grommet
7.Connectthelightconnectorstothelights.
3
8.Securethewireharnesstoeachlightbracketusinga
cabletie(Figure7).
g205225
Figure7
1.Cabletie
9.Connecttheuncappedauxiliarypowerconnectorto
theauxiliarypowerconnectoronthemainwireharness
ofthemachine.
Note:Ifyouinstallanotherpoweredaccessoryto
themachine,plugitintothecappedauxiliarypower
connector.
4
CompletingtheInstallation
NoPartsRequired
Procedure
1.Installthefueltankandfuel-tankbracket;refertothe
Operator’sManualforthemachine.
2.Raisethecushion.
3.Connectthenegative(-)cabletothebattery.
4.Starttheengine.
5.Pressthelightswitchandverifythatthelightsfunction.
4
/