2. Wren Kitchens
  3. 300&600mm Pull Out/Swing Tower Unit

Wren Kitchens 300&600mm Pull Out/Swing Tower Unit Assembly Guide

  • Hello! I am an AI chatbot trained to assist you with the Wren Kitchens 300&600mm Pull Out/Swing Tower Unit Assembly Guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
300 Pull Out
2070
600 Easy Pull
Out Swing
2070
300 Pull Out
2250 Tall
600 Easy Pull
Out Swing
2250 Tall
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
Page 1
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
REQUIRED TOOLS
(F) x16
Wooden Dowel
(J) x36
16mm
Screw
(G) x12
Cam Dowel
(Expanding)
(H) x12
Cam Lock
(M) x4
Cover Cap
(L) x22
15mm
Screw
(K) x7
30mm
Screw
(N) x2
Door Buer
(Z) x24
Shelf Peg
Plastic
Lge L Bracket
x2
Hinge Mouting Plate
x4 Where applicable (Inc Screws)
Hinge
x4 Where applicable
(Inc Screws)
Panel B
x2 End Panel
Panel C
x1 Base Panel
Panel A
x1 Back Panel
Panel E
x2 Rail
Winged
Cover Caps
x2 (Packed separately)
Legs
x5
Frontals
x2 (Packed separately)
Bung
Cover Caps
x2 (Packed
separately)
Fixing Plate (U)
(500 and above, Packed
Separately)
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
Page 2
Step 1.
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels
(B) as shown.
Step 3.
Attach Panels (C) & (E) to panels (B),
using cam dowel (G)
& cam lock (H) (in blue),
and also using dowels (F) (in orange)
in positions as shown on.
Step 4.
Join panels (C) & (E) to (B).
Insert cam lock (H).
Do NOT tighten until Step 6.
NB. All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
E
E
C
B
C
G
F
F G
G F F G
B
GFFG
GFFG
B
G
F
F
G
F
F
G
F
F
G
F
F
DOWEL (F)
& CAM DOWEL (G)
LOCATION DETAIL
B
B
C
C
View from underside
View from underside
H
G
G
H
Seat (G)
cam dowel
into hole as
shown.
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
Page 3
Step 5.
Slide back panel (A) into
groove of end panels (B).
Once back panel (A) is in position,
ensure the panel is ush & square
with bottom of end panels (B).
Step 7.
Ensure carcass is square. Secure back panel (A)
with 6 x 30mm screws (K) equally spaced at
the top and bottom of back panel (A) into
base panels (C), as shown.
Ensure you screw into the Centre of Base
Panel (C) (9mm from bottom edge).
Step 6.
Hand tighten
all cam locks (H), this will
expand cam dowels (G) and tighten
the unit together.
E
A
A
K
K
B
B
C
C
E
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
Page 4
Step 8.
Secure each of the legs into place with 2 x 15mm screws (L) per leg
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass upright.
Once in situ level accordingly.
Step 9.
Lightly hit centre peg of leg base with hammer
until ush with the leg base.
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Front legs should have at edge to the front.
Leg position diagram
C
C
B
B
B
B
Front
Front
C
L
L
C
B
Front
It is important to lift the unit onto its legs. Do not tilt as
depicted in the image.
B
C
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
Page 5
Step 11.
(Not required for 300).
Attach hinge plates onto end panels
(B) In locations shown using 8 x 15mm
screws (L)
Hinge side to be mounted in
accordance to
customer kitchen plan.
Secure tower to the wall using L brackets.
Use 2 x 15mm screws (L) to secure each of the L
brackets to the cabinets at either side. Then screw
through into the wall as shown.
Screws for xing to walls are not provided as
these vary depending on your wall material and
construction. Ensure appropriate xings for wall
Securing to Adjacent Units
Screw into any side units using
the 30mm screws (K) provided to secure to unit.
Screw just to the rear of the Hinge Mounting Plate,
at the top and bottom of both sides of the unit,
place a cover cap on the head to conceal it.
K
2070
See Customer Specific Kitchen Plan
For Tower Frontals
2006mm
846mm
626mm
126mm
1974mm
814mm
594mm
94mm
L
From Base
1826mm
846mm
626mm
126mm
1794mm
814mm
594mm
94mm
L
L
L
L
L
L
L
From Base
TALL
2250
2070
B
B
L
L
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
Page 6
Please refer to separate instructions included
with your Pull Out.
Then no further assembly steps are needed.
300 Pull Out
Repeat on other side for Handleless Frontals
Winged Cover Caps
Bung Cover Caps
Winged
Winged
Bung
Bung
Insert cover caps as shown.
Reverse of Frontals
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
Page 7
Hinge cover caps
Fixing plates
Step 14.
Align doors to join together using xing
plate to the back of
500 & above frontal ensure a 3mm gap
is maintained between each frontal once
xed together.
Screw in place using 8 x 15mm screws on
xing plate.
Step 12.
Insert hinge where required
in holes as shown.
Step 13
Secure hinges
by tightening
2 screws with
hinge dowels
attached.
These are
already
positioned
within the
hinges.
Step 15.
Adjust hinge to suit. As
shown below.
L
L
L
L
L
L
L
L
L
View from Inside of Carcass
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1 & 2.
Point 1 - In - Out
Point 2 - side - side
1
2
FRONTAL HINGE
ADJUSTMENT
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
Step 16.
Fit cover caps to hinge.
Adjust Softclose to suit.
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
Page 8
L
Please refer to separate instructions
included with your pull out.
For Steps 3 of Pull Out
instructions. Use (R) screws
For Steps 4 of Pull Out
instructions. Use (L) screws
For Steps 6 of Pull Out
instructions. Use (R) screws
600 Pull & Swing
Step 3 of pull out
instructions
Step 4 of pull out
instructions
Step 6 of pull out
instructions
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
Page 9
TOWER UNIT
300 & 600 Pull Out/Swing
Assembly Guide
For Internal Use: FI.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev6.indd
Page 10
/