Wren Kitchens Tower Unit 600 2 Door Fridge / Freezer Assembly Guide Assembly Guide

Type
Assembly Guide
TOWER UNIT
600 2 Door Fridge / Freezer Assembly Guide
For Internal Use: FI.WR.INS.041_WKIN00141_TOWER_600_2DrFridgeFreezer.Rev8
2070 x 600
50/50
2070 x 600
70/30
2250 x 600 Tall
50/50
2250 x 600 Tall
70/30
Page 1
TOWER UNIT
600 2 Door Fridge / Freezer Assembly Guide
REQUIRED TOOLS NOT to be
used with CAM
DOWEL & CAM
LOCK
Panel B
x2 End Panel
Panel C
x2 Base Panel
Panel E
x2 Rail Appliance Shelf
x1
Legs
x5
Frontal (packed separately)
x2
70/30 OPTION
50/50 OPTION
L Bracket SML
(FF) x4
Hinge Mounting Plate
x5 Inc Screws
Hinge
x5 Inc Screws
Fixing Plate
(U) x2
(F) x16
Wooden Dowel
(L) x24
15mm
Screw
(G) x16
Cam Dowel
(Expanding)
(H) x12
Cam lock
(M) x4
Cover Cap
(K) x10
30mm
Screw
(N) x2
Door Buer
L Bracket LGE
x2
(Z) x24
Shelf Peg
Plastic
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Page 2
For Internal Use: FI.WR.INS.041_WKIN00141_TOWER_600_2DrFridgeFreezer.Rev8
Step 1.
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
DOWEL (F)
& CAM DOWEL (G)
LOCATION DETAIL
Step 3.
Attach panels (C) and (E) to panels (B), using cam
dowel (G) and also using Dowels (F) (in orange)
in positions as shown.
NB. All cam lock (H) are to be positioned facing
the outside of the unit carcase, for ease of tightening.
Step 4.
Insert cam lock (H).
Do NOT tighten until Step 6.
Do not use power tools with
cam dowel (G) or cam lock (H)
GFF G
GFF G
B
GFFG
GFFG
B
G
F
F
G
F
F
G
F
F
G
F
F
Seat (G)
Cam Dowel
into hole as
shown.
B
B
C
C
View from underside View from underside
H
G
G
H
B
E
E
C
B
C
Page 3
TOWER UNIT
600 2 Door Fridge / Freezer Assembly Guide
B
B
Front
Front
C
Leg position diagram
Step 5.
Position legs as shown.
Ensure legs are rotated to also provide
support to the end panels (B).
Step 6.
Secure each of the legs into place with
4 x 15mm screws (L) per leg.
B
L
L
L
L
C
B
C
Step 7.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit upright.
Once in situ level accordingly.
It is important to lift unit
onto its legs. Do not tilt as
depicted in image.
Page 4
For Internal Use: FI.WR.INS.041_WKIN00141_TOWER_600_2DrFridgeFreezer.Rev8
N.B.
For appliance shelf, secure to panel (B) using
4 x brackets SML (FF) locate according to
customer appliance requirements.
70/30
HINGE
POSITION
50/50
HINGE
POSITION
1826mm
846mm
626mm
126mm 126mm
866mm
1086mm
1826mm
1794mm
814mm
594mm
94mm 94mm
834mm
1054mm
1794mm
Example
locations
ONLY
Example
locations
ONLY
B
B
FFFF FFFF
From Base From Base
1336mm
1304mm
70/30 50/50
FrontFront
INSIDE
FACE
INSIDE
FACE
Step 8.
Attach hinge plates onto end panels
(B) to suit as shown using 2 x screws
already located in hinge plates.
Hinge side or sides to be mounted
in accordance to Customer Specic
Kitchen Plan.
Page 5
TOWER UNIT
600 2 Door Fridge / Freezer Assembly Guide
70/30 50/50
Step 8.
Attach hinge plates onto end panels (B) to suit
as shown using 2 x screws already located in
hinge plates.
Hinge side or sides to be mounted in
accordance to Customer Specic Kitchen
Plan.
N.B.
For appliance shelf, secure to panel (B) using
4 x brackets SML (FF) locate according to
customer appliance requirements.
70/30
HINGE
POSITION
50/50
HINGE
POSITION
Example
locations
ONLY
Example
locations
ONLY
2006mm
846mm
626mm
126mm 126mm
806mm
1026mm
1516mm
2006mm
1974mm
814mm
594mm
94mm 94mm
774mm
994mm
1484mm
1974mm
B B
FF FFFF FF
From Base From Base
1426mm
1394mm
FrontFront
INSIDE
FACE
INSIDE
FACE
Page 6
For Internal Use: FI.WR.INS.041_WKIN00141_TOWER_600_2DrFridgeFreezer.Rev8
Secure tower to the wall using L brackets LGE.
Use 2 x 15mm screws (L) to secure each of the L brackets to
the unit at either side.
Then screw through into the wall as shown.
Secure tower to the wall using screws through rail panel (E)
into the wall as shown.
Screw into any side units using the 30mm screws (K) provided
to secure to unit.
Screw just to the rear of the hinge mounting plates, at the top
and bottom of both sides of the unit, place cover caps (M) on
the head to conceal it.
L
L
E
E
K
Screws for attaching to walls are not provided as these vary depending on
materials, thickness and construction. Ensure appropriate xings for wall
construction are used.
Page 7
TOWER UNIT
600 2 Door Fridge / Freezer Assembly Guide
See Customer Specic Kitchen Plan
For Tower Frontals
Fixing plates
Step 9.
Insert hinge where required
in holes as shown.
Step 10.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 12.
Adjust hinge to suit. As shown below.
U
U
Step 11.
Align frontals to join together using 2 x xing plates (U) to the
back of both frontals ensure a 4mm gap is maintained between
each frontal once xed together.
Screw in place using 4 x 15mm screws (L) per xing plate.
Hinge cover caps
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
View from Inside of unit
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1 & 2.
Point 1 - In - Out
Point 2 - Left - Right
12
FRONTAL HINGE
ADJUSTMENT
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
Step 13.
Fit cover caps to hinge.
Adjust Soft close to suit.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Wren Kitchens Tower Unit 600 2 Door Fridge / Freezer Assembly Guide Assembly Guide

Type
Assembly Guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI