Wren 2070A Assembly Manual

Wren
Brand
Wren
Model
2070A
Type
Assembly Manual

This manual is also suitable for

900/600+290 Appliance
2 Door
600/450+140 Appliance
2 Door
600/450+140 Appliance
1 Door+2 Drawer
450 Appliance
1Door+3 Drawer
A B
C D
2070
2070
2250 Tall
2250 Tall
2070
2070
2250 Tall
2250 Tall
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd
TOWER UNIT
600 Appliance Door & Drawer
Assembly Guide
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
STANDARD DRAWER (packed separately)
Fitting pack contents
DEEP DRAWER (packed separately)
Fitting pack contents
(M) x2
Cover Cap
(R) x 14
Drawer
Runner
16mm Screws
(R) x 14
Drawer
Runner
16mm
Screws
(N) x 1
Door Buer
(N) x 1
Door Buer
(S) x2
21mm
Screw
(S) x2
21mm
Screw
(L) x 2
Gallery Head
(M) x 2
Drawer
Cover Caps
METAL BACK PANEL
x 1
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Left Hand
DRAWER BASE
x 1
DRAWER RUNNER
x 1 Right Hand
FRONTAL
x 1 (Supplied separately)
DRAWER RUNNER
x 1 Left Hand
DRAWER
FRONT FIXING
x 2
METAL BACK PANEL
x 1
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Left Hand
DRAWER BASE
x 1
DRAWER RUNNER
x 1 Right Hand
FRONTAL
x 1 (Supplied separately)
DRAWER RUNNER
x 1 Left Hand
DRAWER
FRONT FIXING
x 2
GALLERY
RAIL
x 2
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psdPage 1
TOWER UNIT
600 Appliance Door & Drawer
Drawer Assembly
Metal back
panel
Step 1.
Secure drawer base to drawer side using
4 x 16mm drawer runner screws (R) in
holes provided.
Seat the edge of drawer base
tight into corner of casing,
as shown.
The decorative face of drawer
base to be positioned as shown.
Repeat step 1 so both drawer sides are
attached to drawer base.
Step 2.
Clip on metal back panel
to drawer base
& drawer sides
Step 3.
Screw back panel in position using
2 x 16mm screws (R) to drawer base
in holes provided.
DRAWER BASE
White decorative
face up
Metal back
panel
Decorative
face
Drawer
base
DRAWER
BASE
R
R
R
R
R
View from
back
Front of drawer
R
R
R
R
R
R
S
Secure  to drawer
frontal using 2 x 21mm screw (S) into
the pilot holes provided as shown.
Step 4.
Frontal attachment
STANDARD
DRAWER

Step 5.
Draw adjustment
Screw point 1 as shown to
adjust drawer frontal right & left.
Screw point 2a as shown to
adjust drawer frontal up & down.
Tighten 2b once in position.
Standard drawer view

& (S)

& (S)
STANDARD
DRAWER
S

Screw point 3 whilst applying
downward pressure as shown to release
View on side of drawer side
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd Page 2
TOWER UNIT
600 Appliance Door & Drawer
Standard Drawer
Assembly
DRAWER
BASE
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psdPage 3
TOWER UNIT
600 Appliance Door & Drawer
Deep Drawer
Assembly
Page 3
Step 2.
Clip on metal back panel to
drawer base & drawer sides.
Step 3.
Screw back panel in position
using 2 x 16mm screws 
to drawer base in holes provided.
Step 1.
Secure drawer base to drawer side using 4 x 16mm
drawer runner screws (R) in holes provided.
Seat the edge of drawer
base tight into corner of
casing, as shown.
The decorative face of
drawer base to be positioned
as shown.
Repeat step 1 so both drawer sides
are attached to drawer base.
Secure  to drawer
frontal using 2 x 21mm screw (S) into
the pilot holes provided, as shown.
Screw point 2a as shown to
adjust drawer frontal up & down.
Tighten 2b once in position
View from
back
Front of drawer
View on side of drawer side
Decorative
face
Drawer
base
Deep drawer


& screw

& screw
S & L S & L
S
S
L
S
1 3 2b 2a
Deep drawer view
Metal back
panel
Metal back
panel
DRAWER BASE
white decorative
face up
R
R
R
R
R
R
R
R
R
R
R
Step 4.
Frontal Attachment
Secure using
1 x15mm screw (S)
into the pilot hole
provided.
Step 5.
Draw Adjustment
Screw point 1 as shown to
adjust drawer frontal right & left.

Screw point 3 whilst applying
downward pressure as shown to release
DEEP
DRAWER
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd Page 4
TOWER UNIT
600 Appliance Door & Drawer
Assembly Guide
Page 4
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
(F) x16
Wooden Dowel
(L) x24
15mm
Screw
(G) x16
Cam Dowel
(Expanding)
(H) x12
Cam lock
(M) x4
Cover Cap
(K) x16
30mm
Screw
(S) x30
19mm
Screw
(N) x2
Door Buer
(N) x12
Shelf Peg
Plastic
LGE L BRACKET
x2
HINGE MOUNTING PLATE
x2 or 4 Inc Screws
HINGE
x2 or 4 Where aplicable
(Inc Screws)
(M) x2
Fixing Plate
Panel B
x1 End Panel
Panel A
x2 Back Panel
Panel E
x2 Rail
Loose Shelf
(where applicable)
x1or 2
 Frontals
(Packed separately)
Fixed Shelf C
x2 Base Panel
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psdPage 5
TOWER UNIT
600 Appliance Door & Drawer
Carcass Assembly
Step 1.
To attach drawer runner
screw into end panels (B)
using 2 x 16mm screws (R)
per drawer rail, into pilot
holes provided, 3rd hole
from front, as shown.
Drawer runner position
B
R
R
R R
B
37mm
from front
from base
261mm
C & D
74mm
C & D
431mm
D
789mm
600/450+140 Appliance
1 Door+2 Drawer
2070 & 2250 Tall
450 Appliance
1Door+3Drawer
2070 & 2250 Talll
C
C
View from underside
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd
Page 6
TOWER UNIT
600 Appliance Door & Drawer
Assembly Guide
FOR PANEL(C) POSITIONS
SEE SHEET 7
B
B
E
C
C
C
C
Step 1.
Dowel (F)
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 2.
Cam Dowel (G)
Seat cam dowel (G) into holes in
both end panels (B) as shown.
Step 3.
Carcass Construction
Attach Panels (C) & (E) to panels (B),
using cam dowel (G) & cam lock (H) (in blue),
and also using dowels (F) (in orange)
in positions as shown on.
SEE SHEET 7 or 8 WHERE APPLICABLE.
Seat (G)
cam dowel
into hole as
shown.
Step 4.
Cam Lock (H)
Join panels (C) & (E) to (B).
Insert cam lock (H). Do NOT
tighten until Step 7.
NB. All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
C
C
H
H
G
G
View from underside View from underside
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psdPage 7
TOWER UNIT
600 Appliance Door & Drawer
Carcass Assembly
2070
from basefrom base
126mm
94mm
126mm
94mm
481mm
449mm
481mm
449mm
626mm
594mm
626mm
594mm
1445mm
1413mm
1445mm
1413mm
1592mm
1560mm
1592mm
1560mm
1826mm
1794mm
1826mm
1794mm
A B C DA B C D
A B C DA B C D
A B C DA B C D
A BA B
AA
AA
B C DB C D
B C DB C D
BB
BB
AA
AA
B CB C
1468mm1468mm
1322mm1322mm
854mm854mm
711mm711mm
568mm568mm
BTMBTM
TOPTOP
HINGE & FIXED SHELF (B)
POSITIONS
600/450+140 Appliance
1 Door+2 Drawer
2070
900/600+290 Appliance
2 Door
2070
450 Appliance
1Door+3 Drawer
2070
600/450+140 Appliance
2 Door
2070
CA
B
LEFT HAND RIGHT HAND
DB
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd Page 8
TOWER UNIT
600 Appliance Door & Drawer
Carcass Assembly
2250 Tall
HINGE & FIXED SHELF (B)
POSITIONS
600/450+140 Appliance
1 Door+2 Drawer
2250 Tall
900/600+290 Appliance
2 Door
2250 Tall
450 Appliance
1Door+3 Drawer
2070
450 Appliance
1Door+3 Drawer
2250 Tall
600/450+140 Appliance
2 Door
2250 Tall
CA DB
from basefrom base
126mm
94mm
126mm
94mm
481mm
449mm
481mm
449mm
626mm
594mm
626mm
594mm
1445mm
1413mm
1445mm
1413mm
1595mm
1563mm
1595mm
1563mm
2006mm
1974mm
2006mm
1974mm
A B C DA B C D
A B C DA B C D
A BA B
AA
AA
B C DB C D
B C DB C D
BB
BB
AA
AA
B CB C
1468mm1468mm
1322mm1322mm
854mm854mm
711mm711mm
568mm568mm
BTMBTM
B
LEFT HAND RIGHT HAND
A B C DA B C D TOPTOP
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd
Page 9
TOWER UNIT
600 Appliance Door & Drawer
Assembly Guide
Step 5.
Cut back panel (A)
to suit appliance
option, to leaving the
centre appliance apperture open.
B
A A
A
A
C
C
E
E
Step 6.
Slide back panel (A) into
groove of end panels (B).
Once back panel (A) is in position,
ensure the panel is ush & square with
bottom of end Ppanels (B).
Step 8.
Ensure carcass is square. Secure back
panel (A) with 12 x 30mm screws (K)
equally spaced at the top & bottom of
back panels (A) into base panels (C),
as shown.
Ensure you screw into the centre of base
panel (C) (9mm from the top or bottom
edge where applicale).
Step 7.
Hand tighten all cam locks (H), this will
expand cam dowels (G) and tighten
the unit together.
C
A
K
K
K
K
A
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd
Page 10
TOWER UNIT
600 Appliance Door & Drawer
Assembly Guide
C
B
Step 9.
Secure each of the
legs into place with
2 x 15mm screws (L).
Step 10.
Lightly hit centre peg of
leg base with hammer
until ush.
Step 11.
Push leg rmly down into leg base.
Adjust legs to 155mm before
turning carcass upright. Once in
situ level accordingly.
Ensure legs are
rotated as shown
so that part of it is
supporting the end
panels (B).
Front legs should
have at edge to the
front.
Front

Front
CC
BB
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd
Page 11
TOWER UNIT
600 Appliance Door & Drawer
Assembly Guide
Secure tower to the wall using screws through
rail panel (E) into the wall as shown.



for wall constructions are used.
L
L
E
E
Secure tower to the wall using L brackets.
Use 2 x 15mm screws (L) to secure each of the
L brackets to the cabinets at either side. Then
screw through into the wall as shown.



for wall constructions are used.
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd
Page 12
TOWER UNIT
600 Appliance Door & Drawer
Assembly Guide
Step 12.
Insert hinge in top & bottom
holes as shown.
FOR TOWER FRONTALS
SEE CUSTOMER SPECIFIC
KITCHEN PLAN
Step 13.
Secure hinges by tightening
2 x screws with plastic grommet
attached. These are already
positioned within the hinges.
Step 14.
Attach the door to unit
where required. Adjust
hinges to suit. See below.
To attach door
clip hinge onto hinge
plate and click to secure.
1
2
To Adjust hinge
Using a screwdriver,
tighten or loosen
as required
at Points 1 & 2
Point 1 - left - right
Point 2 - side - side
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
Fit Cover Caps
to Hinge
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd
Page 13
TOWER UNIT
600 Appliance Door & Drawer
Assembly Guide
For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd
Page 14
TOWER UNIT
600 Appliance Door & Drawer
Assembly Guide
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Wren 2070A Assembly Manual

Wren
Brand
Wren
Model
2070A
Type
Assembly Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents