Page is loading ...
ThermalTronix
TT-MDL-A-SDA Series
Thermal Camera Specifications
User Manual
1
Restriction
Intellisystem Technologies shall reserve copyright of document. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without formal authorization of
Intellisystem Technologies.
Disclaimer
Intellisystem Technologies makes the best to verify the integrity and correctness of the contents in this
document, but no formal guarantee shall be provided. Use of this document and the subsequent results
shall be entirely on the user's own responsibility. Intellisystem Technologies shall have the right to change
the contents of this manual without prior notice for the purpose of enhanced performance.
Warranty
If the product does not operate properly in normal conditions, please let us know. Intellisystem
Technologies will resolve the problem for free of charge. The warranty period is 1 years. However, the
followings are excluded:
If the system behaves abnormally because you run a program irrelevant to the system operation.
Deteriorated performance or natural worn-out in process of time.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
2
Warnings
Please avoid aiming the lens at extreme high temperature radiation source, such as the sun, molten
steel or laser in any situation; otherwise the detector may be damaged.
Please do not touch the lens to avoid contaminating and damaging. Please pay attention to protect
the lens to avoid causing abrasion, scratches even breaches, otherwise, it will affect the device
performance badly, even damage the device.
This device is a precise optoelectronic product. Please protect it properly during usage, storage and
transportation, where improper use (such as drop and collision) will cause damage to the device.
Make sure that the power control connection is reliable. If the power control wire is in bad
connection, it will damage the device.
Ensure the proper connection of power control cable and data cable. Wrong connection may cause
damage to the device.
Do not swag fiercely or collide the device during transportation, otherwise it will cause
performance-reduction and even damage to it.
If the product works abnormally, please contact the dealer or the nearest after-sale service center. Please
do not dismantle or replace it in any manners.
3
Contents
1 Introduction ................................................................................................................................. 4
1.1 FEATURES ................................................................................................................................... 4
1.2 INCLUDED................................................................................................................................... 4
2 Component names and functions ..................................................................................................... 5
2.1 Device appearance ..................................................................................................................... 5
2.2 Connector definition .................................................................................................................. 6
3 OPERATION GUIDE ....................................................................................................................... 6
3.1 Communication parameters ....................................................................................................... 6
3.2 Thermal camera control key description .................................................................................... 6
3.3 CCD camera keys description ..................................................................................................... 7
4 Thermal imaging camera menu ................................................................................................ 7
Before operate thermal camera, please set address 2 firstly ............................................................ 7
4.2 Setting secondary menu ............................................................................................................. 9
4.3 Com sub-menu ......................................................................................................................... 11
4.4 Mode sub-menu ................................................................................................................. 12
4.5 Alarm Value sub-menu ....................................................................................................... 13
5 Technical specifications ............................................................................................................ 14
4
1 Introduction
TT-MDL-A-SDA Series is composed of uncooled infrared thermal imaging module and visible light
camera, which can be applied in the following fields: middle-range power stations, public places;
short-range gate of entry and exit, equipment storage sites; day and night to monitor people, vehicles,
ships and so on.
1.1 FEATURES
Thermal camera
Fixed athermalized lens
AUTO calibration
Manual or Automatic brightness/gain adjustment
Image Noise Reduction function: reduce Image background noise
Image enhancing function : enhance the ability to detect small object
CCD camera
With the state-of-the-art digital signal processing technology, full digital image processing and
special algorithm of 550 TVL high resolution implemented.
High Sensitivity: It implements images of high sensitivity using the up-to–date Super-HAD CCD.
High performance surveillance camera, 25X zoom
PTZ
Preset：128 presets can be setup
Support 0°~360°(pan) continuous rotation
Top load of tilt is -3°~93°
RS485, support PELCO-D/PELCO-P protocol
IP66,full weatherproof
1.2 INCLUDED
TT-MDL-A-SDA Series List for accessories and files：
5
accessory
quantity
remark
Dome Camera
1
AC24 Power Adapter
1
User manual
1
Packing list
1
qualification
1
2 Component names and functions
2.1 Device appearance
2
Pic. 1
No.
Description
Remark
1
Thermal
Thermal camera
2
CCD Camera
Include CCD camera and protocol board
1
6
2.2 Connector definition
The control wire is from bottom of PT system.
Definition as follows:
No.
Description
Remark
1
RS485
RS485+
2
RS485-
4
CCD Video
Analog video output of CCD camera
5
IR Video
Analog video output of thermal imaging camera
6
AC24V
Power supply
7
GND
3 OPERATION GUIDE
3.1 Communication parameters
Thermal camera default address：PELCO-D、baud 2400 (9600), address 2
PT system default address：PELCO-D、baud 2400 (9600), address 1
Visual camera default address：PELCO-D、baud 2400 (9600),address 1
Protocol board address：PELCO-D、baud 2400 (9600), address 1
3.2 Thermal camera control key description
Before the operation. Pls set address 2 firstly.
LENS+
ZOOM+
Calibration
Up
Alarm switch
FOCUS-
ZOOM-
LENS-
Polarity
Down
Digital Zoom
FOCUS+
7
3.3 CCD camera keys description
Before the operation, pls set address 1 firstly
Operational keys
Function
Up
PTZ up
Down
PTZ down
Left
PTZ left
Right
PTZ right
FOCUS-
Near Focus
FOCUS+
Far Focus
ZOOM-
Zoom out
ZOOM+
Zoom in
4 Thermal imaging camera menu
4.1 Main-menu operations
Before operate thermal camera .please set address 2 firstly
Without the menu call preset 100 to activate the main menu. Enter the main menu (pic 2):
Press key “LENS-” move the cursor，Press key “FOCUS+” or “FOCUS-” to change the value where the cursor
is. Auto save when exit
1、Auto: XXX Display the current image auto mode. Three options:
2
3
4
5
6
7
8
1
Pic 2
8
0: manual gain, manual brightness;
1: manual gain, auto brightness;
2: auto gain, auto brightness;（Factory default）
2、G: XXX Gain value, range: 1～1023；
3、B: XXX Brightness value, range
4、P: XXX White/black hot display mode
0: black hot 1: white hot
5、Z：Y/N Zoom status
N：no zoom （default） Y：2X digital zoom
6、Level：X show the range of alarm：From 1 to 6, default is 4
7、 Seting : Activate the setting secondary menu
Press key “FOCUS+” or “FOCUS-”，show the password dialogue
Press “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-” to enter setting menu
dialogue. This password is suitable for all the password dialogue box in the thermal
imaging camera
8、 EXIT : Press key “FOCUS+” or “FOCUS-” to exit
Note ：
All parameters are save automatically after exit
The camera will run the last setup after reboot
9
4.2 Setting secondary menu
In the main menu, move the cursor to “setting” ，press key “FOCUS+” or “FOCUS-” show the
password dialogue，refer to Pic 3 ,Input the password to enter，refer to Pic 4
Press key “LENS-” move the cursor, press key “FOCUS+” or “FOCUS-” to change the value or get into the
submenu where the cursor is 。Auto save when exit
1、 COM: Setup the communication parameters.
2、 Mode : Setup the mode parameters.
3、 AValue: Setup the alarm parameters.
4、 Debug: Debug option only for R&D department of manufacturer
Pic 3
2
3
4
5
6
7
8
1
Pic 4
9
10
10
5、 RECOVER ：H/L/N Setup as H /L/N；
Setup as H： Calibrate 1 time during the 1 minute if working time less than 10
minutes. Calibrate 1 time during 2 minutes if working time between 10 and 30 minutes .calibrate 1
time during 5 minutes if working time between 30 minutes and 1 hour. Calibrate 1 time during 10
minutes if working time more than 1 hour. Calibrate 1 time during 20 minutes if working time more
than 2 hours.
Setup as L：Calibrate 1 time during the 1 minute if working time less than 0 minute.
Calibrate 1 time during 2 minutes if working time between 10 and 30 minutes .calibrate 1 time during 5
minutes if working time more than 30 minutes
Setup as /N： calibrate manually ；
6、 Image: high/middle/low setup as high/middle/low；
Each grade relatively corresponds to a value. It could be setup in the TEST menu .default is
middle
7、 Alarm：X Show the status of gray alarm ：N/Y
N: off；（ Default） Y: On
8、 E：X Show the status of image enhancement，setup as C / 1/2
C:Close；（ default） 1/2：Open relatively enhancement grade
9、 Backup： Factory default
10、 Exit ：XXX Press key “FOCUS+” or “FOCUS-” to exit
11
4.3 Com sub-menu
In the menu “COM”(chapter 4.2 shows how to activate the “com” option)，Press key “LENS-” move the
cursor ，Press key “FOCUS+” or “FOCUS-” to change the value where the cursor is. Refer to Pic 5. Auto
save when exit
1、ID：XXX Address of the IR camera：0~254。
2、BauRate：XXX Baud :1200,2400,4800,9600,14400,19200,38400。
3、Protocol： PELCO-D/PELCO-P。
4、Exit： Press key “LENS+” to exit
Default：Add:1 Baud:9600 Protocol: PELCO-D
1
2
3
4
Pic 5
12
4.4 Mode sub-menu
In the menu “Mode” (chapter 4.2 shows how to activate the “Mode” option)，Press key “LENS-” move the
cursor ，Press key “FOCUS+” or “FOCUS-” to change the value where the cursor is. Refer to Pic 6.Auto
save when exit
1、Gain：XXX Range: 0~255。
2、Bright：XXX Range :0~255。
3、Exit： Press key “LENS+” to exit
Default：Gain:32 Bright:188
1
2
3
Pic 6
13
4.5 Alarm Value sub-menu
In the menu “Avalue” (chapter 4.2 shows how to activate the “Avalue” option)，Press key “LENS-”
move the cursor ，Press key “FOCUS+” or “FOCUS-” to change the value where the cursor is. Refer to
Pic 7.Auto save when exit
1、Level：X Range: 1~6。
2、Threshold：XXX Show the status of Alarm Valve 。
3、AlarmPIX：XXX minimum pixels of alarm.
Such as alarm Number 2 .so the alarm pixel is 2* 2 .totally 4 pixels
4、Exit： Press key LENS+ to exit。
Default: Level and Threshold :(Level 1: 650, relatively temperature difference is 30 ℃. Level 2:1050,
relatively temperature difference is 45 ℃, Level 3:1450, relatively temperature difference is 60 ℃, Level
4:2100, relatively temperature difference is 80 ℃, Level 5:2800, relatively temperature difference is
100 ℃, Level 5:3600, relatively temperature difference is 120℃) AlarmPIX :1
1
2
3
4
Pic 7
14
5 Technical specifications
Items
ThermalTronix
TT-1018MDL-A-SDA
TT-1037MDS-A-SDA
Double visual imaging system
Thermal Camera
Detector type
Uncooled FPA microbolometer
Spectral range
8~14um
Resolution
384×288
Pixel size
25um
Focal length
18mm
37mm
Field of view
30.6°*22.9°
14.8°*11.1°
Lens
Fixed, athermalized
Video out
PAL mode
Frame rate
50Hz
Polarity
White hot/Black hot
Communication
RS485，Support PELCO-D/PELCO-P/Intellisystem
Visual Camera
CCD
Camera
Resolution
PAL:752(H)×582(V) / NTSC:768(H)×494(V)
Imaging device
1/4" SONY EX-View HAD CC
Lens
3.4 mm to 122.4 mm/ F1.6 to F4.5，36X
Horizontal resolution
Color：550TV lines，B/W：570TV lines
Pan&Tilt
Angle info feedback
Support(PELCO-D protocol)
Horizontal angle of rotation
0～360° continuous rotation
Vertical angle of rotation
-3°~93°
Horizontal rotation speed
0.05° -150°/s
Vertical rotation speed
0.05° ~100°/s
Preset
128
Material
Camera body in aluminium alloy, housing in
aluminium alloy
Physical characteristics
Dimensions
Φ245(mm)×375(mm)
Encapsulation
IP66
Weight
7kg
Operation temp
-40°C～55°C
Storage temp
-40°C～70°C
Interface
Video output
PAL; 2 channels
Communication
RS485
Protocol
Support PELCO-D/P
Baud rate
2400/4800/9600 bps
Power Supply
AC24V±4V
Power Consumption
50W
/
