Aztech In-Home Display (IHD) Installation guide

Aztech
Brand
Aztech
Model
In-Home Display (IHD)
Category
TVs & monitors
Type
Installation guide

This manual is also suitable for

Aztech In-Home Display (IHD) is a device that helps you monitor your energy consumption and costs. It can be used to:

  • Track your energy usage in real-time
  • See how much energy your appliances are using
  • Compare your energy usage to previous days, weeks, or months
  • Set energy-saving goals
  • Get alerts when you are using too much energy

The IHD is easy to install and use. Simply plug it into a wall outlet and connect it to your smart meter. The IHD will then start receiving data from your meter and displaying it on its screen.

The IHD has a variety of features that can help you save energy and money. For example, you can use the IHD to:

Aztech In-Home Display (IHD) is a device that helps you monitor your energy consumption and costs. It can be used to:

  • Track your energy usage in real-time
  • See how much energy your appliances are using
  • Compare your energy usage to previous days, weeks, or months
  • Set energy-saving goals
  • Get alerts when you are using too much energy

The IHD is easy to install and use. Simply plug it into a wall outlet and connect it to your smart meter. The IHD will then start receiving data from your meter and displaying it on its screen.

The IHD has a variety of features that can help you save energy and money. For example, you can use the IHD to:

Quick Setup Guide - Elster EnergyAxis
Please contact your utility company for support
Visit myaztech.ca for product User Manual and Configuration Manual
Step 1: Power up your In-Home Display (IHD)
Plug the AC power adaptor into a 120 V AC wall outlet and press the Power button on the right side of your IHD. While your
IHD is normally plugged in, you can unplug it and use Quick Read mode* to spot-check the energy efficiency of your appliances.
Initially, the IHD must be plugged in for at least 4 hours to charge the battery.
Step 3: Wait for IHD to connect to your meter
During this process,
• “Waiting for Utility” will be displayed
• and the light bar will glow red, sweeping back and forth.
When the meter connection is found,
• the information screens will become available for viewing
• and the IHD will begin receiving information from the Smart meter.
Most Smart meters will provide new data every minute. If you are not consuming
much electricity, it may take several minutes or longer to notice any changes.
Note: some meters only provide data hourly.
If no connection is found after 15 minutes,
• move the IHD closer to the meter and allow additional time for the IHD to
connect to the meter.
If no connection is found after moving closer to your meter, please contact
your utility to confirm that your IHD has been registered. Please provide the
following information to your utility:
• LAN ID
• Serial Number
This information is found on the label on the bottom of your IHD.
* Use Quick Read Mode to check the impact of any given appliance on your electricity usage by
comparing the change in usage readings before and after starting the appliance.
NOTE: ALL COSTS ARE FOR INFORMATIONAL AND EDUCATIONAL PURPOSES ONLY AND NOT FOR BILLING.
Step 2: Select Language
• Select the language by using the up or down buttons to scroll.
• Press the center navigation button to select the desired language.
This selection impacts labels on the information screens and menus.
Select
Power
Aztech Associates Inc. provides a limited one year warranty for this product. For details or to obtain warranty support, please visit myaztech.ca
Copyright © 2013 by Aztech Associates, Inc. All rights reserved. No part of this manual may be reproduced, distributed, or transmitted in any form or by
any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of Aztech Associates Inc.
Scroll up and down through screens
IN COST MODE
IN USAGE MODE
Step 4: IHD Operation
*Where data is available
FCC Notices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment uses and generates radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: reorient or relocate the receiving
antenna; Increase the separation between the equipment and receiver; connect the equipment into an outlet on a circuit different from that to which the receiver
is connected; consult the dealer or an experienced radio / TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To comply with
FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This
device must not be co-located or operated in conjunction with any other antenna or transmitter.
Power/ Menus
S 097- 0905 E00 Please contact your utility company for support myaztech.ca
Product is protected under US Patent 8325057, China Patent 101765758, Japan Patent 5026530, NZ patent 579331. Other patents pending.
  • Page 1 1
  • Page 2 2

Aztech In-Home Display (IHD) Installation guide

Aztech
Brand
Aztech
Model
In-Home Display (IHD)
Category
TVs & monitors
Type
Installation guide
This manual is also suitable for

Aztech In-Home Display (IHD) is a device that helps you monitor your energy consumption and costs. It can be used to:

  • Track your energy usage in real-time
  • See how much energy your appliances are using
  • Compare your energy usage to previous days, weeks, or months
  • Set energy-saving goals
  • Get alerts when you are using too much energy

The IHD is easy to install and use. Simply plug it into a wall outlet and connect it to your smart meter. The IHD will then start receiving data from your meter and displaying it on its screen.

The IHD has a variety of features that can help you save energy and money. For example, you can use the IHD to:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents