Heath Zenith 4190 Series User manual

4190 Series
Heath Zenith
Brand
Heath Zenith
Model
4190 Series
Category
Work lights
Type
User manual
Motion Sensing
Diecast Lantern
4190 Series
Features
• Lightcomesonwhenmotionisdetected.
• Automaticallyturnslightoff.
• DuskAccentlighting.
• Photocellkeepsthelightoffduringdaylight
hours.
Requirements
• Thelightcontrolrequires120voltsAC.
• IfyouwanttouseManualMode,thecontrol
mustbewiredthroughaswitch.
• Some codes require installation by a
qualified electrician.
©2012HeathCoLLC 204031-02A
OPERATION
*resetstoAutoModeatdawn.
SettheON-TIMEswitch
on the bottom of the
coverplatetoTEST.
TEST 1 510 MIN
SetON-TIMEswitchto
1,5,or10minutes.
1Second
OFFthen...
Manualmodeonlyworksat
nightbecausedaylightre-
turnsthesensortoAUTO.
Flipthelightswitchofffor
onesecondthenbackonto
togglebetweenAUTOand
MANUALMODE.
Manual mode works only
withtheON-TIMEswitchin
the1,5,or10position.
...backon.
Thispackageincludes:
• Lantern
• Easy to use universal mounting bracket
(X-Bar)
• Mountinghardware
• Wirenuts
Note:Whenrstturnedonwaitabout1
1
/
2
minutesforthecircuitrytocalibrate.
TEST
AUTO
MANUAL MODE
TEST 1 5 10 MIN
Mode: On-Time Works: Day Night
Test 5Seconds x x
Auto 1,5,or10Min x
Manual ToDawn* x
Accent 3,6Hr,toDawn x
2
204031-02
INSTALLATION
Forbestperformance,mountthextureabout
6feet(1.8m)abovetheground.
1.Remove
twonuts.
2.Remove
X-Bar.
Junction
Box
5.AttachX-Barto
junctionbox
Duetothesizeandweightofthexture,you
mayndithelpfultohaveanassistantholdthe
xtureinplacewhileconnectingthewires.
MAX
MIN
3.Tightenscrews
ngertight.
SENSITIVITY
4.Setsensitivityon
xturebacktothe
mid-position.
ON-TIME Switch at 1,
5, or 10 minutes
Mode Switching Summary
Flip light
switch off for
one second
then back on*
MANUAL MODE
AUTO
TEST
* Ifyougetconfusedwhileswitchingmodes,
turnthepoweroffforoneminute,thenback
on.Afterthecalibrationtimethecontrolwill
beintheAUTOmode.
DualBrite
®
Dimmer Control
Lightcomesonhalfbrightforselectedtimeaf-
terdusk(Off,3hr.,6hr.,untildawn).Selecting
OFFdisablesthisfeature.Themotionsensing
featureswillcontinuetoworkasdescribed
inthismanual.Ifmotionissensed,thelight
turnsonfullbrightfortheON-TIME(1,5,or
10minutes)thenreturnstodimmode.
WARNING: Turn power off at circuit
breaker or fuse.
3
204031-02
Recommended Grounding Method
Useagreenground“pigtail”(notprovided)and
twistoneendtogetherwiththebarexturewire
andthe boxgroundwire.Secure withawire
connector.Securetheotherendofthe“pigtail”
withtheGNDscrewontheX-bar.
Blacktoblack
Whitetowhite
WIRING
One Motion Light
❒ Twist the junction box wires and the
xturewirestogetherasshownbelow.
Securewithwireconnectors.Ifyouhave
ametaljunctionbox,youmaynotneed
thegreen“pigtail”.Ifyouareunsureabout
thegroundingmethod,consultyourlocal
buildingcode.
Two Motion Lights
Black
White
Green
orBare
Light
Fixture
Black
White
Green
orBare
Light
Fixture
Light
Fixture
CAUTION: DO NOT connect the RED
wire unless you want to control other
lights from the motion sensor.
Note:Allwiringshouldberuninaccordance
with the National Electrical Code through
conduit or another acceptable means.
Contact a qualified electrician if there is
any question as to the suitability of the
system.
Connectthexturewirestothewiresinthe
junction box. Twist the wires together and
securewithwireconnectors.
4
204031-02
OPTIONAL WIRING
Thisxtureisprovidedwithasensorratedfor360Watts.Sincethextureisonlyrated100
Watts,260Wattsofadditionalloadmaybecontrolledbythissensor.
Whendeterminingwhataxtureisratedfor,donotsimplylookattheratingonthelampin
thexture.Lookatthemarkingwhichspeciesthemaximumlampwattageforwhichthe
xtureissuitable.
Onceyouhaveselectedthexturestobeconnectedanddeterminedtheirmaximumratings,
addtheseratingsup.Forinstance,ifyouhave3xturesrated100Watts,150Watts,and
75Wattsrespectively,youhaveatotalloadof325Watts.
Wiring Diagram 1 –Whenwiringtocontrolastandardlightxture:Stripthemotionsensor’s
redwireandconnecttothestandardlight’sblackwire.Connectallwhitewirestogether.
Totalxtureratingsmustnotexceed360Watts(3.0A).
Wiring Diagram 2 –Whenwiringtocontrolanothermotionsensinglightxture(Master/
Slave):Striptheredwireinbothlightxtures.Connecttheredwireofthecontrolling(master)
xturetotheredandblackwiresofthecontrolled(slave)xture.Connectallwhitewires
together.Totalxtureratingsmustnotexceed360Watts(3.0A).
Wiring Diagram 1
Black
White
Green
orBare
Light
Fixture
Light
Fixture
Wiring Diagram 2
(Standard)
Master Slave
Itisalsopossibletowiretwomotionlightssothateitherxturewillturnonbothlightsatthe
sametime(dualmastersystem).Itisrecommendedthatonlypeoplewithplentyofelectrical
experienceattemptthisconguration.Pleasecallourcustomerservicenumber(1-800-858-
8501-Englishspeakingonly)beforeattemptingthiswiring.If the dual master wiring is not
done correctly, it can destroy both motion sensing fixtures and void your warranty.
Black
White
Green
orBare
Light
Fixture
Light
Fixture
Red
Red
5
204031-02
COMPLETE THE INSTALLATION
❒ Stuffthewiresintothejunctionbox.Make
surenoneofthewiresgetpinched.
Slidethextureontothe
mountingscrewsand
tightennuts.
❒ Installone 100 Wattmaximumlightbulb,or
three 60 Wattbulbsincandelabrastyle.
❒ Install the fixture top. Secure with
decorativescrews.
❒ Aftercompletingthetestsonpage5,caulk
fixture mounting surfacewithsilicone
weathersealant.
Junction
Box
Model 4193 Glass Installation
❒ Model 4193 only: install the six pieces
ofglassbyslidingthemdownasshown.
The glass panels should rest upon the
cornerguidesoneachside,andagainst
therubberbumpersatthebottom.
Note:Aswithanyglass,handlewithcare.
Corner
Guides
RubberBumpers
6
204031-02
TESTING
❒ Turn on the circuit breaker and light
switch.
Thedetectorislesssensitivetomotiondi-
rectlytowardsitandmoresensitivetoacross
motion.
Sensor
Motion
Least Sensitive Most Sensitive
❒ Walk through thecoverage area noting
whereyouarewhenthelightsturnon.
❒ If you need to change the sensitivity,
temporarilyremovethextureandmake
theadjustment.Toomuchsensitivitymay
increasefalsetriggering.
❒ SettheamountofTIMEyouwantthelight
tostayonaftermotionisdetected.(1,5,
or10minutes).
❒ Settheamountoftimeafterduskyouwant
thelightsonaccentlevel.
NOTE: Sensorhasa1
1
/
2
minutewarmuppe-
riodbeforeitwilldetectmotion.When
rstturnedon,wait1
1
/
2
minutes.
TEST1510MIN
ON-TIME
OFF 3 6 DUSK TO
HOUR DAWN
Avoid aiming the control at:
•Objectsthatchangetemperaturerapidly,
suchasheating vents and air condition-
ers.Theseheatsourcescouldcausefalse
triggering.
•Areaswherepets or trafficmaytrigger
thecontrol.
•Nearby large, light-colored objects
reecting light may trigger the shut-off
feature. Do not point other lights at the
sensor.
30ft.
(9.1m)
Maximum Range Maximum
Coverage Angle
6ft.
(1.8m)
180°
Motion
❒ Switchtheon-timetoTESTpositionand
DualBrite
®
switchtotheOFFposition.
7
204031-02
SPECIFICATIONS
Range........... Up to 30 ft. (9.1 m)
[varieswithsurrounding
temperature]
SensingAngle..... Upto180°
ElectricalLoad..... See rating on xture
formaximumwattage
SensorCapacity ... Upto360Watts(3.0A.)
Maximum Tungsten
Incandescent
PowerRequirements 120VAC,60Hz
OperatingModes... TEST, AUTO, and
MANUALMODE
TimeDelay ....... 1,5,10minutes
DualBrite
®
Timer... Off,3,6hours,dusk-to
dawn
HeathCoLLCreservestherighttodiscontinue
products and to change specications at
any time without incurring any obligation
to incorporate new features in products
previouslysold.
TROUBLESHOOTING GUIDE
SYMPTOM
Light stays on
continuously.
Light flashes
on and off.
POSSIBLE CAUSE
1. Thesensorispointedtoward
a heat source like an air
vent, dryer vent, or brightly-
paintedheat-reectivesurface.
(Reduce sensitivity.)
2. LightcontrolisinManualMode.
(Switch to Auto.)
3. Light control is in DualBrite
®
mode.
4. Sensitivityissettoohigh.(Re-
duce sensitivity.)
1. Light control is in the Test
mode and warming up.
(Flashing is normal under
these conditions).
2. Heatbeingreectedfromother
objects may be affecting the
sensor.(Reduce sensitivity.)
POSSIBLE CAUSE
1.Lightswitchisturnedoff.
2.Bulbislooseorburnedout.
3.Fuseisblownorcircuitbreaker
isturnedoff.
4.Daylight turn-off is in effect
(recheck after dark).
5.Incorrectcircuitwiring,ifthisis
anewinstallation.
1.Lightcontrolmaybeinstalledin
arelativelydarklocation.
2.Light control is in Test. (Set
control switch to an ON-TIME
position.)
1.Lightcontrolmaybesensingsmall
animals or automobile trafc
(Reduce sensitivity).
2.Sensitivityissettoohigh.(Re-
duce sensitivity.)
SYMPTOM
Light will not
come on.
Light comes on
in daylight.
Light comes on
for no apparent
reason.
8
204031-02
TWO YEAR LIMITED WARRANTY
Thisisa“LimitedWarranty”whichgivesyouspeciclegalrights.Youmayalsohaveotherrights
whichvaryfromstatetostateorprovincetoprovince.
Foraperiodoftwoyearsfromthedateofpurchase,anymalfunctioncausedbyfactorydefective
partsorworkmanshipwillbecorrectedatnochargetoyou.
Not Covered - Repairservice,adjustmentandcalibrationduetomisuse,abuseornegligence,
lightbulbs,batteries,andotherexpendableitemsarenotcoveredbythiswarranty.Unauthorized
serviceormodicationoftheproductorofanyfurnishedcomponentwillvoidthiswarrantyinits
entirety.Thiswarrantydoesnotincludereimbursementforinconvenience,installation,setuptime,
lossofuse,unauthorizedservice,orreturnshippingcharges.
ThiswarrantycoversonlyHeathCoLLCassembledproductsandisnotextendedtootherequip-
mentandcomponentsthatacustomerusesinconjunctionwithourproducts.
THISWARRANTY ISEXPRESSLY INLIEUOFALL OTHERWARRANTIES,EXPRESSOR
IMPLIED,INCLUDINGANYWARRANTY,REPRESENTATIONORCONDITIONOFMERCHANT
ABILITYORTHATTHEPRODUCTSAREFITFORANYPARTICULARPURPOSEORUSE,
ANDSPECIFICALLYINLIEUOFALLSPECIAL,INDIRECT,INCIDENTAL,ORCONSEQUEN-
TIALDAMAGES.
REPAIRORREPLACEMENTSHALLBETHESOLEREMEDYOFTHECUSTOMERANDTHERE
SHALLBENOLIABILITYONTHEPARTOFHEATHCOLLCFORANYSPECIAL,INDIRECT,
INCIDENTAL, OR CONSEQUENTIALDAMAGES,INCLUDING BUT NOTLIMITEDTO ANY
LOSSOFBUSINESSOR PROFITS,WHETHERORNOT FORESEEABLE. Some states or
provincesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,sothe
abovelimitationorexclusionmaynotapplytoyou.
Please keep your dated sales receipt, it is required for all warranty requests.
TECHNICAL SERVICE
Please call 1-800-858-8501 (English speaking only) for assistance before returning
product to store.
Ifyouexperienceaproblem,followthisguide.YoumayalsowanttovisitourWebsiteat:
www.hzsupport.com.Iftheproblempersists,call*forassistanceat1-800-858-8501(English
speakingonly),8:00AMto5:00PMCST(M-F).Youmayalsowrite*to:
HeathCoLLC
P.O.Box90045,BowlingGreen,KY42102-9045
ATTN:TechnicalService
*IfcontactingTechnicalService,pleasehavethefollowinginformationavailable:Model
Number,DateofPurchase,andPlaceofPurchase.
No Service Parts Available for this Product
Please keep your dated sales receipt, it is required for all warranty requests.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Heath Zenith 4190 Series User manual

4190 Series
Heath Zenith
Brand
Heath Zenith
Model
4190 Series
Category
Work lights
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents