Heath Zenith HZ-4191-BK User manual

Motion Sensing

Diecast Lantern

4190 Series

Features

• Lightcomesonwhenmotionisdetected.

• Automaticallyturnslightoff.

• DuskAccentlighting.

• Photocellkeepsthelightoffduringdaylight

hours.

Requirements

• Thelightcontrolrequires120voltsAC.

• IfyouwanttouseManualMode,thecontrol

mustbewiredthroughaswitch.

• Some codes require installation by a

qualiﬁed electrician.

©2012HeathCoLLC 204031-02A

OPERATION

*resetstoAutoModeatdawn.

SettheON-TIMEswitch

on the bottom of the

coverplatetoTEST.

TEST 1 510 MIN

SetON-TIMEswitchto

1,5,or10minutes.

1Second

OFFthen...

Manualmodeonlyworksat

nightbecausedaylightre-

turnsthesensortoAUTO.

Flipthelightswitchofffor

onesecondthenbackonto

togglebetweenAUTOand

MANUALMODE.

Manual mode works only

withtheON-TIMEswitchin

the1,5,or10position.

...backon.

Thispackageincludes:

• Lantern

• Easy to use universal mounting bracket

(X-Bar)

• Mountinghardware

• Wirenuts

Note:Whenrstturnedonwaitabout1

1

/

2

minutesforthecircuitrytocalibrate.

TEST

AUTO

MANUAL MODE

TEST 1 5 10 MIN

Mode: On-Time Works: Day Night

Test 5Seconds x x

Auto 1,5,or10Min x

Manual ToDawn* x

Accent 3,6Hr,toDawn x

2

204031-02

INSTALLATION

Forbestperformance,mountthextureabout

6feet(1.8m)abovetheground.

1.Remove

twonuts.

2.Remove

X-Bar.

Junction

Box

5.AttachX-Barto

junctionbox

Duetothesizeandweightofthexture,you

mayndithelpfultohaveanassistantholdthe

xtureinplacewhileconnectingthewires.

MAX

MIN

3.Tightenscrews

ngertight.

SENSITIVITY

4.Setsensitivityon

xturebacktothe

mid-position.

ON-TIME Switch at 1,

5, or 10 minutes

Mode Switching Summary

Flip light

switch off for

one second

then back on*

MANUAL MODE

AUTO

TEST

* Ifyougetconfusedwhileswitchingmodes,

turnthepoweroffforoneminute,thenback

on.Afterthecalibrationtimethecontrolwill

beintheAUTOmode.

DualBrite

®

Dimmer Control

Lightcomesonhalfbrightforselectedtimeaf-

terdusk(Off,3hr.,6hr.,untildawn).Selecting

OFFdisablesthisfeature.Themotionsensing

featureswillcontinuetoworkasdescribed

inthismanual.Ifmotionissensed,thelight

turnsonfullbrightfortheON-TIME(1,5,or

10minutes)thenreturnstodimmode.

WARNING: Turn power off at circuit

breaker or fuse.

3

204031-02

Recommended Grounding Method

Useagreenground“pigtail”(notprovided)and

twistoneendtogetherwiththebarexturewire

andthe boxgroundwire.Secure withawire

connector.Securetheotherendofthe“pigtail”

withtheGNDscrewontheX-bar.

Blacktoblack

Whitetowhite

WIRING

One Motion Light

❒ Twist the junction box wires and the

xturewirestogetherasshownbelow.

Securewithwireconnectors.Ifyouhave

ametaljunctionbox,youmaynotneed

thegreen“pigtail”.Ifyouareunsureabout

thegroundingmethod,consultyourlocal

buildingcode.

Two Motion Lights

Black

White

Green

orBare

Light

Fixture

Black

White

Green

orBare

Light

Fixture

Light

Fixture

CAUTION: DO NOT connect the RED

wire unless you want to control other

lights from the motion sensor.

Note:Allwiringshouldberuninaccordance

with the National Electrical Code through

conduit or another acceptable means.

Contact a qualiﬁed electrician if there is

any question as to the suitability of the

system.

Connectthexturewirestothewiresinthe

junction box. Twist the wires together and

securewithwireconnectors.

4

204031-02

OPTIONAL WIRING

Thisxtureisprovidedwithasensorratedfor360Watts.Sincethextureisonlyrated100

Watts,260Wattsofadditionalloadmaybecontrolledbythissensor.

Whendeterminingwhataxtureisratedfor,donotsimplylookattheratingonthelampin

thexture.Lookatthemarkingwhichspeciesthemaximumlampwattageforwhichthe

xtureissuitable.

Onceyouhaveselectedthexturestobeconnectedanddeterminedtheirmaximumratings,

addtheseratingsup.Forinstance,ifyouhave3xturesrated100Watts,150Watts,and

75Wattsrespectively,youhaveatotalloadof325Watts.

Wiring Diagram 1 –Whenwiringtocontrolastandardlightxture:Stripthemotionsensor’s

redwireandconnecttothestandardlight’sblackwire.Connectallwhitewirestogether.

Totalxtureratingsmustnotexceed360Watts(3.0A).

Wiring Diagram 2 –Whenwiringtocontrolanothermotionsensinglightxture(Master/

Slave):Striptheredwireinbothlightxtures.Connecttheredwireofthecontrolling(master)

xturetotheredandblackwiresofthecontrolled(slave)xture.Connectallwhitewires

together.Totalxtureratingsmustnotexceed360Watts(3.0A).

Wiring Diagram 1

Black

White

Green

orBare

Light

Fixture

Light

Fixture

Wiring Diagram 2

(Standard)

Master Slave

Itisalsopossibletowiretwomotionlightssothateitherxturewillturnonbothlightsatthe

sametime(dualmastersystem).Itisrecommendedthatonlypeoplewithplentyofelectrical

experienceattemptthisconguration.Pleasecallourcustomerservicenumber(1-800-858-

8501-Englishspeakingonly)beforeattemptingthiswiring.If the dual master wiring is not

done correctly, it can destroy both motion sensing ﬁxtures and void your warranty.

Black

White

Green

orBare

Light

Fixture

Light

Fixture

Red

5

204031-02

COMPLETE THE INSTALLATION

❒ Stuffthewiresintothejunctionbox.Make

surenoneofthewiresgetpinched.

Slidethextureontothe

mountingscrewsand

tightennuts.

❒ Installone 100 Wattmaximumlightbulb,or

three 60 Wattbulbsincandelabrastyle.

❒ Install the fixture top. Secure with

decorativescrews.

❒ Aftercompletingthetestsonpage5,caulk

ﬁxture mounting surfacewithsilicone

weathersealant.

Junction

Box

Model 4193 Glass Installation

❒ Model 4193 only: install the six pieces

ofglassbyslidingthemdownasshown.

The glass panels should rest upon the

cornerguidesoneachside,andagainst

therubberbumpersatthebottom.

Note:Aswithanyglass,handlewithcare.

Corner

Guides

RubberBumpers

6

204031-02

TESTING

❒ Turn on the circuit breaker and light

switch.

Thedetectorislesssensitivetomotiondi-

rectlytowardsitandmoresensitivetoacross

motion.

Sensor

Motion

Least Sensitive Most Sensitive

❒ Walk through thecoverage area noting

whereyouarewhenthelightsturnon.

❒ If you need to change the sensitivity,

temporarilyremovethextureandmake

theadjustment.Toomuchsensitivitymay

increasefalsetriggering.

❒ SettheamountofTIMEyouwantthelight

tostayonaftermotionisdetected.(1,5,

or10minutes).

❒ Settheamountoftimeafterduskyouwant

thelightsonaccentlevel.

NOTE: Sensorhasa1

1

/

2

minutewarmuppe-

riodbeforeitwilldetectmotion.When

rstturnedon,wait1

1

/

2

minutes.

TEST1510MIN

ON-TIME

OFF 3 6 DUSK TO

HOUR DAWN

Avoid aiming the control at:

•Objectsthatchangetemperaturerapidly,

suchasheating vents and air condition-

ers.Theseheatsourcescouldcausefalse

triggering.

•Areaswherepets or trafﬁcmaytrigger

thecontrol.

•Nearby large, light-colored objects

reecting light may trigger the shut-off

feature. Do not point other lights at the

sensor.

30ft.

(9.1m)

Maximum Range Maximum

Coverage Angle

6ft.

(1.8m)

180°

Motion

❒ Switchtheon-timetoTESTpositionand

DualBrite

®

switchtotheOFFposition.

7

204031-02

SPECIFICATIONS

Range........... Up to 30 ft. (9.1 m)

[varieswithsurrounding

temperature]

SensingAngle..... Upto180°

ElectricalLoad..... See rating on xture

formaximumwattage

SensorCapacity ... Upto360Watts(3.0A.)

Maximum Tungsten

Incandescent

PowerRequirements 120VAC,60Hz

OperatingModes... TEST, AUTO, and

MANUALMODE

TimeDelay ....... 1,5,10minutes

DualBrite

®

Timer... Off,3,6hours,dusk-to

dawn

HeathCoLLCreservestherighttodiscontinue

products and to change specications at

any time without incurring any obligation

to incorporate new features in products

previouslysold.

TROUBLESHOOTING GUIDE

SYMPTOM

Light stays on

continuously.

Light ﬂashes

on and off.

POSSIBLE CAUSE

1. Thesensorispointedtoward

a heat source like an air

vent, dryer vent, or brightly-

paintedheat-reectivesurface.

(Reduce sensitivity.)

2. LightcontrolisinManualMode.

(Switch to Auto.)

3. Light control is in DualBrite

®

mode.

4. Sensitivityissettoohigh.(Re-

duce sensitivity.)

1. Light control is in the Test

mode and warming up.

(Flashing is normal under

these conditions).

2. Heatbeingreectedfromother

objects may be affecting the

sensor.(Reduce sensitivity.)

POSSIBLE CAUSE

1.Lightswitchisturnedoff.

2.Bulbislooseorburnedout.

3.Fuseisblownorcircuitbreaker

isturnedoff.

4.Daylight turn-off is in effect

(recheck after dark).

5.Incorrectcircuitwiring,ifthisis

anewinstallation.

1.Lightcontrolmaybeinstalledin

arelativelydarklocation.

2.Light control is in Test. (Set

control switch to an ON-TIME

position.)

1.Lightcontrolmaybesensingsmall

animals or automobile trafc

(Reduce sensitivity).

2.Sensitivityissettoohigh.(Re-

duce sensitivity.)

SYMPTOM

Light will not

come on.

Light comes on

in daylight.

Light comes on

for no apparent

reason.

8

204031-02

TWO YEAR LIMITED WARRANTY

Thisisa“LimitedWarranty”whichgivesyouspeciclegalrights.Youmayalsohaveotherrights

whichvaryfromstatetostateorprovincetoprovince.

Foraperiodoftwoyearsfromthedateofpurchase,anymalfunctioncausedbyfactorydefective

partsorworkmanshipwillbecorrectedatnochargetoyou.

Not Covered - Repairservice,adjustmentandcalibrationduetomisuse,abuseornegligence,

lightbulbs,batteries,andotherexpendableitemsarenotcoveredbythiswarranty.Unauthorized

serviceormodicationoftheproductorofanyfurnishedcomponentwillvoidthiswarrantyinits

entirety.Thiswarrantydoesnotincludereimbursementforinconvenience,installation,setuptime,

lossofuse,unauthorizedservice,orreturnshippingcharges.

ThiswarrantycoversonlyHeathCoLLCassembledproductsandisnotextendedtootherequip-

mentandcomponentsthatacustomerusesinconjunctionwithourproducts.

THISWARRANTY ISEXPRESSLY INLIEUOFALL OTHERWARRANTIES,EXPRESSOR

IMPLIED,INCLUDINGANYWARRANTY,REPRESENTATIONORCONDITIONOFMERCHANT

ABILITYORTHATTHEPRODUCTSAREFITFORANYPARTICULARPURPOSEORUSE,

ANDSPECIFICALLYINLIEUOFALLSPECIAL,INDIRECT,INCIDENTAL,ORCONSEQUEN-

TIALDAMAGES.

REPAIRORREPLACEMENTSHALLBETHESOLEREMEDYOFTHECUSTOMERANDTHERE

SHALLBENOLIABILITYONTHEPARTOFHEATHCOLLCFORANYSPECIAL,INDIRECT,

INCIDENTAL, OR CONSEQUENTIALDAMAGES,INCLUDING BUT NOTLIMITEDTO ANY

LOSSOFBUSINESSOR PROFITS,WHETHERORNOT FORESEEABLE. Some states or

provincesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,sothe

abovelimitationorexclusionmaynotapplytoyou.

Please keep your dated sales receipt, it is required for all warranty requests.

TECHNICAL SERVICE

Please call 1-800-858-8501 (English speaking only) for assistance before returning

product to store.

Ifyouexperienceaproblem,followthisguide.YoumayalsowanttovisitourWebsiteat:

www.hzsupport.com.Iftheproblempersists,call*forassistanceat1-800-858-8501(English

speakingonly),8:00AMto5:00PMCST(M-F).Youmayalsowrite*to:

HeathCoLLC

P.O.Box90045,BowlingGreen,KY42102-9045

ATTN:TechnicalService

*IfcontactingTechnicalService,pleasehavethefollowinginformationavailable:Model

Number,DateofPurchase,andPlaceofPurchase.

No Service Parts Available for this Product

Please keep your dated sales receipt, it is required for all warranty requests.

Page is loading ...

Heath Zenith HZ-4191-BK User manual

Related papers

Other documents