Xerox 220 ST Installation guide

Brand: Xerox

Model: 220 ST

Category: Laser/LED printers

Type: Installation guide

This manual is also suitable for

230 ST

The Document Company

XEROX

DC220/230ST NetWare

4.x

NDS Quick Install

1. Connect the DC220/230 to your network

outlet or cable.

2. Enter System Administrator Setups:

a) Press the [Access] button on the

Control Panel.

b) Enter the System Administrator

password by typing #22222

(# key and 22222) on the keypad and

pressing [Enter] on the screen.

Note: #22222 is the factory default

password and may be changed by

your Xerox service representative to

suit your needs.

3. Access the NetWare Setup screens:

a) On the screen, press [Print Setups].

b) Press [Network Setups].

c) Press [NetWare].

4. Enable NetWare:

a) Press [Enablement].

b) Press [Enabled].

5. Select the appropriate interface and frame

type for your network:

a) Press [Interface].

b) On the right half of the screen, select

[Ethernet] or [Token Ring] as the

appropriate interface for your network.

Note: Token Ring will not be available

as a selection unless it has been

installed and configured.

c) Select the appropriate frame type for

your network; IEEE_802.3,

Ethernet II, or IEEE_802.2.

IMPORTANT:During the next two steps, be

sure to enter the Print Server name and the Print

Server Password exactly the same as the

values entered in PCONSOLE or NWADMIN.

6. Enter the Print Server name:

a) Press [Print Server Name].

b) Press [Edit].

c) Using the keyboard on the screen,

enter the Print Server Name for the

printer. Additional characters are

available by pressing the Change

Keyboard button in the upper right

corner of the screen.

d) Press [Save].

Over

Installation Requirements:

If this is a Token Ring installation, the Token

Ring card must be installed by your Xerox ser-

vice representative and configured before per-

forming this procedure. Refer to the Token Ring

Quick Install card.

If running NLSP, be sure that RIP/SAP

compatibility is configured on the same segment

as the DC220/230.

Note: For a Bindery installation, refer to the

NetWare 3.1x/4.1x Bindery Quick Install card.

Before Installation:

Perform the network installation of the printer

using the appropriate NetWare

utilities (PCONSOLE or NWADMIN).

• Record the following information for use

during setup at the DC220/230:

Print Server name:_______________________

Print Server Password:____________________

NDS Tree:______________________________

NDS Name Context:______________________

Frame Type:____________________________

Poll Interval:____________________________

For assistance, contact your local Xerox Customer Support Center:

USA: 1-800-821-2797 Canada: 1-800-939-3769

The Document Company

XEROX

DC220/230ST NetWare

4.x

NDS Quick Install

c) Use the keyboard on the screen dis-

play to enter the NDS Name Context

for your printer. The fully qualified

name should be used for NDS Trees

with a country code. Refer to the

following examples noticing that there

are no leading or trailing dots:

Example A – NDS Name Context for a Tree with

a country:

OU=SALES.O=MYCOMPANY.C=US

Example B – NDS Name Context for a Tree

without a country:

SALES.MYCOMPANY

d) Press [Save].

10.Enter a dash as the Primary File Server

name:

a) Press the [Additional Setups] button

in the upper right corner of the screen.

b) Press [Primary File Server 1].

c) Press [Edit].

d) Press Change Keyboard (if necessary)

and put a [-] (dash) in the field.

e) Press [Save].

11.Enter the Poll Interval:

a) Press [Poll Interval].

b) Use the arrow keys to scroll to the

desired number. The default setting

is 5. The range is 1 to 240 seconds.

12.Press [Save].

13.Press [Exit]. The DC220/230 will reboot

and print a configuration sheet in approxi-

mately 3 minutes.

14.Check the settings on the configuration

sheet against those that were set up on

the Server.

15.At the client, install print drivers and map

the printer in the usual manner. Refer to

the CentreWare

manual, Getting Started

with Print and Fax Services for additional

information.

Additional information on the NetWare setup can

be found in the DC220/230 System

Administration Guide.

7. Enter the Print Server Password:

a) Press [Print Server Password].

b) Press [Edit] and enter the password

that was assigned. If a password was

not assigned, use the Backspace key

to delete the default password.

c) Press [Save].

8. Enter the NDS Tree:

a) Press [NDS Tree].

b) Press [Edit].

c) Using the keyboard on the screen

display, enter the name of the

appropriate NDS Tree.

d) Press [Save].

9. Enter the NDS Name Context:

a) Press [NDS Name Context].

b) Press [Edit].

701P97985 Version 1.1, 5-98

For assistance, contact your local Xerox Customer Support Center:

USA: 1-800-821-2797 Canada: 1-800-939-3769

Xerox 220 ST Installation guide

Brand: Xerox

Model: 220 ST

Category: Laser/LED printers

Type: Installation guide

This manual is also suitable for

230 ST

Download PDF

report

Xerox 220 ST Installation guide

This manual is also suitable for

Xerox 220 ST Installation guide

Related papers

Other documents