Xerox 220 ST Installation guide

220 ST
Xerox
Brand
Xerox
Model
220 ST
Type
Installation guide

This manual is also suitable for

Xerox 220 ST is a network printer that offers fast and reliable printing for small offices and workgroups. It features Ethernet and Token Ring connectivity, allowing easy integration into existing networks. With its user-friendly control panel and intuitive software, the Xerox 220 ST is simple to set up and use. It supports various printing protocols, including NetBIOS/NetBEUI, making it compatible with a wide range of operating systems and devices.

Xerox 220 ST is a network printer that offers fast and reliable printing for small offices and workgroups. It features Ethernet and Token Ring connectivity, allowing easy integration into existing networks. With its user-friendly control panel and intuitive software, the Xerox 220 ST is simple to set up and use. It supports various printing protocols, including NetBIOS/NetBEUI, making it compatible with a wide range of operating systems and devices.

The Document Company
XEROX
DC220/230ST Windows NT
®
4.0 NetBIOS/NetBEUI Quick Install
b) Enter the System Administrator
password by typing #22222
(# key and 22222) on the keypad and
pressing [Enter] on the screen.
Note: #22222 is the factory default
password and may be changed by
your Xerox service representative to
suit your needs.
3. Access the Setup screens:
a) On the screen display, press [Print
Setups].
b) Press [Network Setups].
c) Press [NetBIOS/NetBEUI].
4. Enable NetBIOS/NetBEUI:
a) Press [Enablement].
b) Press [Enabled].
5. Select the appropriate interface:
a) Press [Interface].
b) On the right half of the screen, select
[Ethernet] or [Token Ring] as the
appropriate interface for your network.
Note:Token Ring will not be available
as a selection unless it has been
installed and configured.
6. Enter the Host Name:
a) Press [Host Name], then press [Edit]
and use the keyboard on the screen to
enter the Host Name for your network
(14 characters or less).
b) Press [Save].
7. Enter the Printer Name:
a) Press [Printer Name], then press
[Edit] and use the keyboard on the
screen to enter the Printer Name for
your network (15 characters or less).
b) Press [Save].
Over
Installation Requirements:
If this is a Token Ring installation, the Token
Ring card must be installed by your Xerox ser-
vice representative and configured before per-
forming this procedure. Refer to the Token Ring
Quick Install card.
Before Installation:
Record the following information for use during
setup at the DC220/230:
Host Name:_____________________________
Printer Name:___________________________
Workgroup:_____________________________
1. Connect the DC220/230 to your network
outlet or cable.
2. Enter System Administration Setups:
a) Press the [Access] button on the
Control Panel.
For assistance, contact your local Xerox Customer Support Center:
USA: 1-800-821-2797 Canada: 1-800-939-3769
The Document Company
XEROX
DC220/230ST Windows NT
®
4.0 NetBIOS/NetBEUI Quick Install
12.Check the settings on the configuration
sheet against those that were entered.
13.At the client, install print drivers and map
the printer in the usual manner. Refer to
the CentreWare
®
manual, Getting Started
with Print and Fax Services for additional
information.
Additional information on this installation proce-
dure can be found in the DC220/230 System
Administration Guide.
8. Enter the Workgroup name:
a) Press [Workgroup], then press [Edit]
and use the keyboard on the screen to
enter the Workgroup Name.
b) Press [Save].
9. Press [Save].
10.Press [Exit].
11.The DC220/230 will reboot and print a
configuration sheet in approximately 3
minutes.
©1998 Xerox Corporation
701P97991 Version 1.1, 5-98
For assistance, contact your local Xerox Customer Support Center:
USA: 1-800-821-2797 Canada: 1-800-939-3769
  • Page 1 1
  • Page 2 2

Xerox 220 ST Installation guide

220 ST
Xerox
Brand
Xerox
Model
220 ST
Type
Installation guide
This manual is also suitable for

Xerox 220 ST is a network printer that offers fast and reliable printing for small offices and workgroups. It features Ethernet and Token Ring connectivity, allowing easy integration into existing networks. With its user-friendly control panel and intuitive software, the Xerox 220 ST is simple to set up and use. It supports various printing protocols, including NetBIOS/NetBEUI, making it compatible with a wide range of operating systems and devices.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents