Xerox 220 ST Installation guide

Category
Laser/LED printers
Type
Installation guide

This manual is also suitable for

Xerox 220 ST is a versatile network printer that offers high-quality printing, copying, and scanning capabilities. It features a fast print speed of up to 20 pages per minute and a resolution of 600 x 600 dpi, ensuring sharp and professional-looking documents. With its Ethernet and Token Ring connectivity options, the Xerox 220 ST can easily integrate into various network environments. Additionally, it supports PCL and PostScript languages, making it compatible with a wide range of software and applications.

Xerox 220 ST is a versatile network printer that offers high-quality printing, copying, and scanning capabilities. It features a fast print speed of up to 20 pages per minute and a resolution of 600 x 600 dpi, ensuring sharp and professional-looking documents. With its Ethernet and Token Ring connectivity options, the Xerox 220 ST can easily integrate into various network environments. Additionally, it supports PCL and PostScript languages, making it compatible with a wide range of software and applications.

The Document Company
XEROX
DC220/230ST NetWare
®
3.1x/4.1x
Bindery Quick Install
Over
4. Enable NetWare:
a) Press [Enablement].
b) Press [Enabled].
5. Select the appropriate interface and frame
type for your network.
a) Press [Interface].
b) On the right half of the screen, select
[Ethernet] or [Token Ring] as the
appropriate interface for your network.
Note: Token Ring will not be available
as a selection unless it has been
installed and configured.
c) Select the appropriate frame type for
your network: IEEE_802.3,
Ethernet II, or IEEE_802.2.
IMPORTANT: During the next two steps, be
sure that the Print Server name and the Print
Server Password are exactly the same as the
values entered in PCONSOLE.
6. Enter the Print Server name:
a) Press [Print Server Name].
Frame Type:____________________________
Poll Interval:____________________________
1. Connect the DC220/230 to your network
outlet or cable.
2. Enter System Administrator Setups:
a) Press the [Access] button on the
Control Panel.
b) Enter the System Administrator
password by typing #22222
(# key and 22222) on the keypad and
pressing [Enter] on the screen.
Note: #22222 is the factory default
password and may be changed by
your Xerox service representative to
suit your needs.
3. Access the NetWare Setup screens:
a) On the screen display, press [Print
Setups].
b) Press [Network Setups].
c) Press [NetWare].
Installation Requirements:
If this is a Token Ring installation, the Token
Ring card must be installed by your Xerox ser-
vice represenvative and configured before per-
forming this procedure. Refer to the Token Ring
Quick Install card.
If running NLSP, be sure that RIP/SAP
compatibility is configured on the same segment
as the DC220/230.
Note: For a NDS installation, refer to the
NetWare 4.x NDS Quick Install card.
Before Installation:
Perform the network installation for the
printer using the appropriate NetWare utility
(PCONSOLE).
Note: Define the printer as
Defined Elsewhere or Remote/Other.
Record the following information for use
during setup at the DC220/230:
Print Server name:_______________________
Print Server Password:____________________
File Server name:________________________
The Document Company
XEROX
DC220/230ST NetWare
®
3.1x/4.1x
Bindery Quick Install
9. In a Bindery only installation, set the NDS
Name Context to a dash:
a) Press [NDS Name Context].
b) Press [Edit].
c) Use the left arrow key on the keyboard
on the screen to delete any characters
currently in the field and then press [-].
Setting the NDS name context to a
dash disables NDS for a Bindery
installation.
d) Press [Save].
10.Press the [Additional Setups] button in
the upper right corner of the screen.
11.Press [Primary File Server 1].
Note: This step is REQUIRED to obtain
the correct connectivity.
a) Press [Edit].
b) Use the keyboard on the screen
to enter the name of the NetWare
server where you created the queue.
c) Press [Save].
d) To enter the names of additional file
servers, press [Primary File Server 2]
etc, and repeat the above steps.
Note: Each additional server requires the
identical Print Server Name and Pass-
word.
12.Enter the Poll Interval:
a) Press [Poll Interval].
b) Use the arrow keys to scroll to the
desired number. The default setting
is 5. The range is 1 to 240 seconds.
13.Press [Save].
14.Press [Exit] on the Network Setups
screen. The DC220/230 will reboot and
print a configuration sheet in approxi-
mately 3 minutes.
15.Check the settings on the configuration
sheet against those that were set up on
the Server.
16.At the client, install print drivers and map
the printer in the usual manner. Refer to
the CentreWare manual, Getting Started
with Print and Fax Services, for additional
information.
Additional information on the NetWare setup can
be found in the DC220/230 System Administra-
tion Guide.
b) Press [Edit] and use the keyboard on
the screen to enter the Print Server
Name for the printer.
Note: Additional characters are available by
pressing the Change Keyboard button in the
upper right corner of the screen.
c) Press [Save].
7. Enter the Print Server Password:
a) Press [Print Server Password].
b) Press [Edit] and enter the password
that was assigned to the Print Server.
If a password was not assigned, use
the Backspace key to delete the
default password.
c) Press [Save].
8. In a Bindery only installation, set the NDS
Tree name to a dash.
a) Press [NDS Tree].
c) Press [Edit] and use the left arrow key
on the keyboard on the screen to
delete any characters currently in the
field and then press [-]. Setting the
NDS Tree to a dash disables NDS for
a Bindery installation.
d) Press [Save].
©1998 Xerox Corporation
701P97984 Version 1.1, 5-98
For assistance, contact your local Xerox Customer Support Center:
USA: 1-800-821-2797 Canada: 1-800-939-3769
  • Page 1 1
  • Page 2 2

Xerox 220 ST Installation guide

Category
Laser/LED printers
Type
Installation guide
This manual is also suitable for

Xerox 220 ST is a versatile network printer that offers high-quality printing, copying, and scanning capabilities. It features a fast print speed of up to 20 pages per minute and a resolution of 600 x 600 dpi, ensuring sharp and professional-looking documents. With its Ethernet and Token Ring connectivity options, the Xerox 220 ST can easily integrate into various network environments. Additionally, it supports PCL and PostScript languages, making it compatible with a wide range of software and applications.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI