VISUAL COMFORT CD 5025 User manual

Type
User manual

VISUAL COMFORT CD 5025 is a stunning chandelier that will add a touch of elegance to any room. With its adjustable arms and rods, you can customize the height and width of the fixture to perfectly fit your space. The chandelier comes with four glass shades that diffuse the light beautifully, creating a warm and inviting atmosphere. Installation is easy with the included instructions and mounting hardware.

VISUAL COMFORT CD 5025 is a stunning chandelier that will add a touch of elegance to any room. With its adjustable arms and rods, you can customize the height and width of the fixture to perfectly fit your space. The chandelier comes with four glass shades that diffuse the light beautifully, creating a warm and inviting atmosphere. Installation is easy with the included instructions and mounting hardware.

Lomme XL Chandelier
Item # CD 5025
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
NOTICE:
US
M
L
I
D
S
E
T
Phillips Screwdriver Slotted Screwdriver Wire Strippers
Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Rotate fixture arms into position as shown in diagram 1.
3. Remove mounting plate (F) from canopy (I) by removing collar
ring (J).
4. Install mounting plate (F) to the junction box and secure with mounting
screws (H).
5. Connect supply ground wire (usually green or bare copper) around the
green grounding screw (see diagram 2). Tighten.
NOTE: It is imperative that the fixture is grounded.
6. Feed electrical wire through bottom rod (M) and connect to fixture (N).
Repeat for middle rod (L), connecting to bottom rod (M).
7. Continue feeding wire through collar ring (J), canopy (I) and top
rod (K).
8. Holding fixture upright, slide collar ring (J) and canopy (I) down and
rest on fixture (N). Then connect top rod (K) to middle rod (L).
NOTE: Slide components down slowly to avoid damages.
9. Hang fixture swivel ball (T) to the center of mounting plate (F) and
secure with set screw (P) using provided wrench (Q). See diagram 1.
10. Cut excess wire, being sure to leave enough to reach the junction
box. Separate wire and strip insulation on each 5/8".
E
E
P
Q
F
G
H
K
J
M
N
R
T
L
I
Diagram 2
Diagram 1
Lomme XL Chandelier
Item # CD 5025
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
11. Connect driver (G) input neutral wire (white) to the supply neutral wire
(usually white) using wire nut (E).
12. Connect driver (G) input hot wire (black) to the supply hot wire (usually
black) using wire nut (E).
CAUTION: Do not reverse the hot and neutral connections.
13. Connect fixture neutral wire (black) to driver (G) output wire (black)
using wire nut (E).
14. Connect fixture hot wire (red) to driver (G) output wire (red) using wire
nut (E).
CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck into the
junction box.
16. Insert driver (G) into mounting plate bracket.
17. Install canopy (I) to mounting plate (F) and secure with collar ring (J).
18. Thread glass shades (A) to fixture (N). See diagram 3. Repeat for
glass shades (B & C & D).
NOTE: Do not over-tighten otherwise shade could become damaged.
19. Remove protective cover (R) from rods (S1) carefully, then install
to glass shades (A). Repeat for rods (S2 & S3 & S4).
See diagram 4.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
US
M
L
I
D
S
E
T
Diagram 3
GND
C
B
A
B
D
E
E
F
G
H
K
J
M
N
R
T
L
I
Diagram 4
191mm
D288mm * H166mm
D248mm * H423mm
S1
D219mm * H280mm
D248mm * H249mm
AB
S2
86mm
S4
321mm
D
S3
176mm
C
  • Page 1 1
  • Page 2 2

VISUAL COMFORT CD 5025 User manual

Type
User manual

VISUAL COMFORT CD 5025 is a stunning chandelier that will add a touch of elegance to any room. With its adjustable arms and rods, you can customize the height and width of the fixture to perfectly fit your space. The chandelier comes with four glass shades that diffuse the light beautifully, creating a warm and inviting atmosphere. Installation is easy with the included instructions and mounting hardware.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI