VISUAL COMFORT CD 5025 User manual

Brand: VISUAL COMFORT

Model: CD 5025

Type: User manual

VISUAL COMFORT CD 5025 is a stylish and functional chandelier that will add a touch of elegance to any room. It features a sleek metal frame with four glass shades that provide ample lighting. The chandelier is easy to install and comes with all the necessary hardware. It is also UL listed for safety and peace of mind.

Lomme XL Chandelier

Item # CD 5025

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

NOTICE:

Phillips Screwdriver Slotted Screwdriver Wire Strippers

Wire Cutters

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (B) from canopy (F) by removing collar

ring (G).

3. Install mounting plate (B) to the junction box and secure with mounting

screws (D).

4. Connect supply ground wire (usually green or bare copper) around the

green grounding screw (see diagram 1). Tighten.

NOTE: It is imperative that the fixture is grounded.

5. Feed electrical wire through bottom rod (J) and connect to fixture (K).

Repeat for middle rod (I), connecting to bottom rod (J).

6. Continue feeding wire through collar ring (G), canopy (F) and top

rod (H).

7. Holding fixture upright, slide collar ring (G) and canopy (F) down and

rest on fixture (K). Then connect top rod (H) to middle rod (I).

NOTE: Slide components down slowly to avoid damages.

8. Hang fixture swivel ball (E) to the center of mounting plate (B) and

secure with set screw (P) using provided wrench (Q). See diagram 1.

9. Cut excess wire, being sure to leave enough to reach the junction

box. Separate wire and strip insulation on each 5/8".

Diagram 1

Diagram 2

Diagram 3

GND

191mm [7 1/2"]

86mm [3 3/8"]

321mm [12 5/8"]

176mm [6 7/8"]

Lomme XL Chandelier

Item # CD 5025

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

10. Connect driver (C) input neutral wire (white) to the supply neutral wire

(usually white) using wire nut (A).

11. Connect driver (C) input hot wire (black) to the supply hot wire (usually

black) using wire nut (A).

CAUTION: Do not reverse the hot and neutral connections.

12. Connect fixture neutral wire (black) to driver (C) output wire (black)

using wire nut (A).

13. Connect fixture hot wire (red) to driver (C) output wire (red) using wire

nut (A).

CAUTION: Do not reverse the hot and neutral connections.

14. Make sure all wire connections are tight, then carefully tuck into the

junction box.

15. Insert driver (C) into mounting plate bracket.

16. Install canopy (F) to mounting plate (B) and secure with collar ring (G).

17. Thread glass shades (L1) to fixture (K). See diagram 2. Repeat for

glass shades (L2 & L3 & L4).

NOTE: Do not over-tighten otherwise shade could become damaged.

18. Remove protective cover (M) from rods (N1) carefully, then install

to glass shades (L1). Repeat for rods (N2 & N3 & N4).

See diagram 3.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do

not use abrasive or chemical agents.

NOTICE:

Diagram 1

Diagram 2

Diagram 3

GND

191mm [7 1/2"]

86mm [3 3/8"]

321mm [12 5/8"]

176mm [6 7/8"]

VISUAL COMFORT CD 5025 User manual

VISUAL COMFORT CD 5025 User manual

VISUAL COMFORT CD 5025 User manual

Related papers

Other documents