circa LIGHTING RL 5131 User manual

Brand
circa LIGHTING
Model
RL 5131
Type
User manual

The circa LIGHTING RL 5131 is a stylish and versatile chandelier that can be used to create a variety of looks in your home. With its modular design, you can choose to install the fixture with the bulbs facing up or down, and you can adjust the length of the chain to create the perfect height for your space. The chandelier comes with all the necessary hardware for easy installation, and it is compatible with a variety of bulb types, so you can customize the lighting to suit your needs.

The circa LIGHTING RL 5131 is a stylish and versatile chandelier that can be used to create a variety of looks in your home. With its modular design, you can choose to install the fixture with the bulbs facing up or down, and you can adjust the length of the chain to create the perfect height for your space. The chandelier comes with all the necessary hardware for easy installation, and it is compatible with a variety of bulb types, so you can customize the lighting to suit your needs.

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove collar loop (C) from chain (F) by removing quick link (D).
3. Install mounting plate (B) to junction box and secure with mounting
screws (K).
4. Secure collar loop (C) to mounting plate (B) using pliers to tighten
locknut.
5. Install canopy (E) to collar loop (C) by securing with collar ring (J).
6. Attach hanging rods (H) to hooks on fixture body (I) and to the
bottom hooks on fixture loop (G) using quick links.
NOTE: Fixture can be installed with bulbs up or down.
7. Determine desired overall length, and amount of chain (F) needed.
Shorten chain using chain pliers. (Keep extra chain)
8. Attach chain (F) to collar loop (C) and to fixture loop (G) using quick
links (D).
9. Thread fixture wire and ground wire through chain (E).
NOTE: When you reach the collar loop (C), ensure there is no tension
on the wires. Cut excess wires, being sure to leave about 12” to reach
the junction box.
10. Separate two sides of molded wire, and strip insulation on each 5/8".
Roark 30" Modular Ring Chandelier
Item # RL 5131
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Chain Pliers
Slip Joint Pliers Measuring Tape Wire Cutters
Wire Strippers
NOTICE:
Diagram 1
A
B
J
K
C
H
E
G
I
D
D
F
RALPH LAUREN
Option 1
Option 2
Bulbs not included
Roark 30" Modular Ring Chandelier
Item # RL 5131
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
11. Loosen collar ring (J) and let canopy (E) slip down chain (E) carefully.
12. Twist all fixture wires together. Slip through center hole of collar
loop (C).
NOTE: Untwist wires and separate to prepare for connection.
13. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (A).
14. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually
white) using wire nut (A).
15. Connect fixture hot wire (smooth with markings) to the supply hot
wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
16. Make sure all wire connections are tight, then carefully tuck into the
junction box.
17. Install canopy (E) to collar loop (C) by securing with collar ring (J).
18. Insert bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
Diagram 1
A
B
J
K
C
H
E
G
I
D
D
F
RALPH LAUREN
Option 1
Option 2
Bulbs not included
  • Page 1 1
  • Page 2 2

circa LIGHTING RL 5131 User manual

Brand
circa LIGHTING
Model
RL 5131
Type
User manual

The circa LIGHTING RL 5131 is a stylish and versatile chandelier that can be used to create a variety of looks in your home. With its modular design, you can choose to install the fixture with the bulbs facing up or down, and you can adjust the length of the chain to create the perfect height for your space. The chandelier comes with all the necessary hardware for easy installation, and it is compatible with a variety of bulb types, so you can customize the lighting to suit your needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents