VISUAL COMFORT TOB 5726 User manual

Type
User manual

VISUAL COMFORT TOB 5726 is a large chandelier designed to enhance the ambiance of your living space with its elegant design. It requires assembly and electrical installation by a qualified person. The chandelier features multiple rods and a canopy, allowing for height adjustment to suit your ceiling. It supports multiple bulbs, providing ample illumination. Assembly instructions are included, guiding you through the process of attaching the mounting plate, connecting the rods, and installing the shades. Please follow the instructions carefully for safe and proper installation.

VISUAL COMFORT TOB 5726 is a large chandelier designed to enhance the ambiance of your living space with its elegant design. It requires assembly and electrical installation by a qualified person. The chandelier features multiple rods and a canopy, allowing for height adjustment to suit your ceiling. It supports multiple bulbs, providing ample illumination. Assembly instructions are included, guiding you through the process of attaching the mounting plate, connecting the rods, and installing the shades. Please follow the instructions carefully for safe and proper installation.

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (A) from canopy (D) by removing collar
ring (E).
3. Install mounting plate (A) to junction box and secure with mounting
screws (B).
4. Feed electrical and ground wires through bottom rod (I) and connect
to fixture (M). Repeat for middle rod (H), connecting to bottom rod (I).
Repeat for middle rod (G), connecting to middle rod (H) .
5. Continue feeding wires through collar ring (E) and canopy (D).
6. Holding fixture upright, slide collar ring (E) and canopy (D) down and
rest on fixture (M). Then connect top rod (F) to middle rod (G).
NOTE: Slide components down slowly to avoid damages.
7. Hang fixture swivel ball (N) to the center of mounting plate (A).
8. Cut excess wires, being sure to leave enough to reach the junction
box. Separate wires, and strip insulation on each 5/8”.
9. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (C).
NOTE: It is imperative that the fixture is grounded.
Turlington Large Chandelier
Item # TOB 5726
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Wire Cutters
Wire Strippers
NOTICE:
A
C
B
G
Diagram 1
Bulbs not included
F
I
J (Packaged separately)
H
E
D
L
K
M
N
10. Connect fixture neutral wire (white) to the supply neutral wire (usually
white) using wire nut (C).
11. Connect fixture hot wire (black) to the supply hot wire (usually black)
using wire nut (C).
CAUTION: Do not reverse the hot and neutral connections.
12. Make sure all wire connections are tight, then carefully tuck into the
junction box.
13. Install canopy (D) to mounting plate (A) and secure with collar ring (E).
14. Place shade (J) upside down on clean surface and attach bracket (C)
by securing with cap screws (K). Repeat with other shades.
15. Install shade bracket (L) to fixture (M).
16. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
Not use abrasive or chemical agents.
Turlington Large Chandelier
Item # TOB 5726
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
A
C
B
G
Diagram 1
Bulbs not included
F
I
J (Packaged separately)
H
E
D
L
K
M
N
  • Page 1 1
  • Page 2 2

VISUAL COMFORT TOB 5726 User manual

Type
User manual

VISUAL COMFORT TOB 5726 is a large chandelier designed to enhance the ambiance of your living space with its elegant design. It requires assembly and electrical installation by a qualified person. The chandelier features multiple rods and a canopy, allowing for height adjustment to suit your ceiling. It supports multiple bulbs, providing ample illumination. Assembly instructions are included, guiding you through the process of attaching the mounting plate, connecting the rods, and installing the shades. Please follow the instructions carefully for safe and proper installation.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI