One Stop Gardens 66558 Set Up And Operating Instructions Manual

Brand: One Stop Gardens

Model: 66558

Type: Set Up And Operating Instructions Manual

BOY/FISH WATER FOUNTAIN

BIRD BATH

66558

SET UP AND OPERATING INSTRUCTIONS

Distributed exclusively by Harbor Freight Tools

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2008 by Harbor Freight Tools

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

SKU 66558 For technical questions, please call 1-800-444-3353. Page 2

Before start-up, note the following:

The pump can be connected to any

shock-proof plug which has been installed

according to regulations. The plug must

have a supply voltage of 110 V~ at 60 Hz.

WARNING

IMPORTANT! For your own safety –

before starting to run the pump, please

have the following items checked by an

expert:

Risk of electric shock – This pump is 1.

supplied with a grounding conductor

and grounding-type attachment plug.

To reduce the risk of electric shock,

connect only to a properly grounded,

grounding-type receptacle.

Risk of electric shock – This pump 2.

has not been investigated for use in

swimming pool areas.

The electrical connections must be 3.

protected from moisture.

If there is danger of ooding, the 4.

electrical connections must be taken

to higher ground.

Circulation of caustic uids, as well 5.

as the circulation of abrasive materi-

als, must be avoided at all costs.

The pump must be protected from 6.

frost.

The pump must be protected from 7.

running dry.

Access by children should also be 8.

prevented with appropriate mea-

sures.

Operate outdoors only. 9.

WARNING: Handling the Power Cord 10.

on this product will expose you to

lead, a chemical known to the State

of California to cause cancer, and

birth defects or other reproductive

harm. Wash hands after handling.

(California Health & Safety Code §

25249.5, et seq.)

The warnings, precautions, and in-11.

structions discussed in this instruction

manual cannot cover all possible con-

ditions and situations that may occur.

It must be understood by the operator

that common sense and caution are

factors which cannot be built into this

product, but must be supplied by the

operator.

Fluid Type

The Pump is designed for use with

water only with a maximum temperature

of 77° F (25°C). Do not use the pump for

other uids, especially not fuels, cleaning

uids, or other chemical products.

SPECIFICATIONS

Electrical Requirements 110 V~ / 60 Hz, 4W

UNPACKING

When unpacking, check to make sure

that the item is intact and undamaged. If

any parts are missing or broken, please

call Harbor Freight Tools at the number

shown on the cover of this manual as soon

as possible.

SKU 66558 For technical questions, please call 1-800-444-3353. Page 3

INSTALLATION

Power Supply

The pump is equipped with a shock-1.

proof plug according to regulations.

The pump is designed to be connect-

ed to 110 V~, 60 Hz safety socket.

Make sure that the socket is suf-2.

ciently secured and is in excellent

condition.

WARNING! If the power cord or plug is

damaged, do not use the pump. The

power cord or plug may only be re-

paired by a certied electrician.

Assembly

With the Base (3) on a at, level 1.

surface, place the bottom end of the

Connector (2) into the opening in the

center of the Base and twist. The

built-in tabs on both will lock each

other together. (See Assembly draw-

ing for these steps.)

Slide bottom of Pole (1) into the top 2.

opening of the Connector and twist,

locking both together.

Insert the plug and cord through Pole. 3.

Run the cord all the way down and 4.

out the bottom of the Base.

Put the Plug of the cord through an 5.

opening in the Base and out the side.

Lower the Basin all the way onto the 6.

top of the Pole and twist to lock it on.

Attach the Boy Figurine (5) onto the 7.

Pump Cover.

Connect the Pump to the water inlet 8.

of the Pump Cover beneath the Boy

Figurine with the Tube (8).

Place the Pump Cover into position 9.

in the Basin with the Pump resting

on the bottom of the Pump compart-

ment.

Press the round end of the cover into 10.

the round part at the center of the

Basin.

Press and snap the Pump Cover end 11.

into position at the edge of the Basin.

Place the Boy Fish Water Fountain 12.

Bird Bath on a level surface.

Anchor the Water Fountain securely 13.

to the ground by driving the three

supplied “L” Stakes through small

openings in the Base and into the

lawn or dirt. Verify that installation

surface has no hidden utility lines

before driving Stakes.

OPERATION

The regulator switch on the end of 1.

the pump adjusts ow rate.

Fill the Basin (7) with clean water.2.

Plug the power cord into a properly 3.

fused GFCI outlet. Do not allow the

plug to get wet.

Add additional water if necessary.4.

SKU 66558 For technical questions, please call 1-800-444-3353. Page 4

MAINTENANCE

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION:

Unplug the Pump from its

electrical outlet before

performing any inspection,

maintenance, or cleaning

procedures.

Quarterly Maintenance

The below maintenance must be per-

formed at least once every 3 months under

optimal conditions. For frequent use, or

dirty areas, more frequent maintenance is

required.

1. Unplug the power cord

before maintenance.

Remove the Pump Cover

from the Basin (7).

Rinse out the Basin (7) and Pump 2.

compartment (see Assembly drawing)

with clean water.

Open the Pump housing by pulling 3.

off the Filter Screen (4A).

(see Pump

Diagram for the following steps)

Remove the Regulator (4B), Cover a.

(4C) and Rotor.

Wash these components in clean b.

water.

Clean off the Filter screen (4A).c.

Run a stream of clean water through 4.

the Rotor (4D) channel to ush out

any contaminants.

Reassemble the Pump in the reverse 5.

order as disassembled.

FIGURE B

6. Remove the Pump Cover. Using a

garden hose, shoot a stream of water

through the water channel leading

from the bottom of the Boy Figurine

(5) and out the mouth of the sh.

Rinse out any sand and sludge that 7.

may have accumulated in the Pump

compartment.

SKU 66558 For technical questions, please call 1-800-444-3353. Page 5

Troubleshooting

Problem Possible Causes Possible Solutions

Pump runs, but

will not deliver any

water.

Clogged Screen (see Pump 1.

Diagram)

The pump water height is 2.

below the minimum water

level.

Low line voltage.3.

Remove Screen. Clean out dirt and debris 1.

from Screen and impeller. Then replace

Screen.

Fill Basin. 2.

Consult an electrician.3.

Pump won’t start

or run.

Check power connections and 1.

circuits/fuses.

Water level too low.2.

Screen and/or impeller 3.

clogged.

Defective pump.4.

Consult an electrician.1.

Fill Basin 2.

Remove Screen. Clean out dirt and debris 3.

from Screen and impeller. Then replace

Screen.

Have a qualied service technician repair or 4.

replace.

Excessive noise or

vibration.

Debris in impeller. Remove Screen. Clean Rotor in clean water

with toothbrush. Then replace Screen.

Follow all safety precautions whenever diagnosing or servicing the

tool. Disconnect power supply before service.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT

HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/

OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD

BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE

BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTS THERETO.

SKU 66558 For technical questions, please call 1-800-444-3353. Page 6

Part Description Qty.

1 Pole 1

2 Connector 1

3 Base 1

4 Pump Assembly 1

Part Description Qty.

5 Boy Figurine 1

6 Pump Cover 1

7 Basin 1

8 Tube 1

PARTS LIST

Pump

Compartment

ASSEMBLY DIAGRAM

SKU 66558 For technical questions, please call 1-800-444-3353. Page 7

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not avail-

able individually as replacement parts.

PUMP DIAGRAM

Part Description Qty.

4A Filter Screen 1

4B Regulator 1

4C Cover 1

4D Rotor 1

4E Pump Housing 1

Part Description Qty.

4F Adapter 1

4G Shaft 1

4H Suction Cup 27

4I Back Cover 1

One Stop Gardens 66558 Set Up And Operating Instructions Manual

One Stop Gardens 66558 Set Up And Operating Instructions Manual

One Stop Gardens 66558 Set Up And Operating Instructions Manual

Related papers

Other documents