One Stop Gardens 4831 Assembly And Operating Instructions Manual
- Type
- Assembly And Operating Instructions Manual
BARREL FOUNTAIN WITH PUMP
Model
4831
ASSEMBLY AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright
©
2003 by Harbor Freight Tools
®
. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 09k
Page 2 For technical questions, please call 1-800-444-3353. SKU 4831
SAVE THIS MANUAL
Keep this manual for the safety warnings
and precautions, assembly, operating,
inspection, maintenance and cleaning
procedures. Write the product’s serial number
in the back of the manual near the assembly
diagram (or month and year of purchase if
product has no number). Keep this manual
and the receipt in a safe and dry place for
future reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling, and
all other information provided with
this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that follow
this symbol to avoid possible
injury or death.
DANGER indicates a
hazardous situation
which, if not avoided, will result
in death or serious injury.
WARNING indicates a
hazardous situation
which, if not avoided, could
result in death or serious injury.
CAUTION, used with
the safety alert
symbol, indicates a hazardous
situation which, if not avoided,
could result in minor or moderate
injury.
NOTICE is used to
address practices not
related to personal injury.
CAUTION, without the
safety alert symbol, is
used to address practices not
related to personal injury.
General Pump Safety Warnings
WARNING Read all safety warnings
and instructions. Failure to follow the
warnings and instructions may result
in electric shock, re and/or serious
injury.
Save all warnings and instructions
for future reference.
WORK AREA
Keep your work area clean and well 1.
lit. Cluttered benches and dark areas
invite accidents.
Do not operate pumps in explosive 2.
atmospheres, such as in the presence
of ammable liquids, gases, or dust.
Do not operate this pump unless it is
submerged in water.
Keep bystanders, children, and 3.
visitors away while operating a pump.
Do not allow anyone to put their hands in
the Barrel if the pump is plugged in.
ELECTRICAL SAFETY
Grounded pumps must be plugged 1.
into an outlet properly installed and
grounded in accordance with all
codes and ordinances. Never remove
the grounding prong or modify the
plug in any way. Do not use any
adapter plugs. Check with a qualied
electrician if you are in doubt as
to whether the outlet is properly
grounded. If the pumps should
Page 3For technical questions, please call 1-800-444-3353.SKU 4831
electrically malfunction or break down,
grounding provides a low resistance path
to carry electricity away from the user.
Avoid body contact with grounded 2.
surfaces such as pipes, radiators,
ranges, and refrigerators. There is an
increased risk of electric shock if your
body is grounded.
Do not abuse the Power Cord.3.
Never use the Power Cord to carry
the pumps or pull the Plug from an
outlet. Keep the Power Cord away
from heat, oil, sharp edges, or moving
parts. Replace damaged Power Cords
immediately. Damaged Power Cords
increase the risk of electric shock.
When operating a pump outside, use 4.
an outdoor extension cord marked
“W-A” or “W”. These extension cords
are rated for outdoor use, and reduce the
risk of electric shock.
PERSONAL SAFETY
Stay alert. Watch what you are 1.
doing, and use common sense when
operating a power product. Do not
use a pump while tired or under
the inuence of drugs, alcohol, or
medication. A moment of inattention
while operating pumps may result in
serious personal injury.
Dress properly. Do not wear loose 2.
clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves
away from moving parts. Loose
clothes, jewelry, or long hair can be
caught in moving parts.
Avoid accidental starting.3. Be sure the
Pump is fully submerged in water and
nobody has their hands or any body
parts in the barrel before plugging in
the Pump.
Do not overreach. Keep proper 4.
footing and balance at all times.
Use safety equipment. Always wear 5.
eye protection during set-up.
PRODUCT USE AND CARE
Do not force the product. Use the 1.
correct product for your application.
The correct product will do the job better
and safer at the rate for which it is
designed.
Disconnect the Power Cord Plug from 2.
the power source before making any
adjustments, changing accessories,
or storing the pump. Such preventive
safety measures reduce the risk of
starting the pump accidentally.
Store idle pumps out of reach of 3.
children and other untrained persons.
Pumps are dangerous in the hands of
untrained users.
Maintain pumps with care. Keep 4.
pumps clean. Do not use a damaged
pump. Tag damaged pumps “Do not
use” until repaired.
Check for misalignment or binding of 5.
moving parts, breakage of parts, and
any other condition that may affect
the pump’s operation. If damaged,
have the pump serviced before using.
Many accidents are caused by poorly
maintained pumps.
Do not modify this product.6. This is a
decorative pump and is not designed for
any other use.
Use only accessories that are 7.
recommended by the manufacturer
for your model. Accessories that may
be suitable for one product may become
hazardous when used on another
product.
Page 4 For technical questions, please call 1-800-444-3353. SKU 4831
SERVICE
Pump service must be performed only 1.
by qualied repair personnel. Service
or maintenance performed by unqualied
personnel could result in a risk of injury.
When servicing a pump, use only 2.
identical replacement parts. Follow
instructions in the “Inspection,
Maintenance, And Cleaning” section
of this manual. Use of unauthorized
parts or failure to follow maintenance
instructions may create a risk of electric
shock or injury.
SPECIFIC SAFETY RULES
Maintain labels and nameplates on 1.
the Pump. These carry important
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
Wear ANSI-approved safety impact 2.
eye goggles when setting up
the Pump. Using personal safety
devices reduce the risk for injury.
Maintain a safe working environment. 3.
Keep the work area well lit. Make
sure there is adequate surrounding
workspace. Always keep the work
area free of obstructions, grease, oil,
trash, and other debris. Do not use a
power product in areas near ammable
chemicals, dusts, and vapors
Unplug the Pump from its electrical 4.
outlet before performing any
inspection, maintenance, or cleaning
procedures.
People with pacemakers should 5.
consult their physician(s) before use.
Electromagnetic elds in close proximity
to heart pacemaker could cause
pacemaker interference or pacemaker
failure.
Set-up the Fountain Pump on a level 6.
surface away from children and
pets. If necessary create a boundary
to keep children and pets away to avoid
drowning or electrocution. Children and
pets need constant adult supervision
near the Fountain Pump.
Never leave the Fountain Pump 7.
unattended during operation. Do not
run the Pump if unattended. Unplug the
pump when not in use.
WARNING:8. Handling the cord on this
product will expose you to lead, a
chemical known to the State of California
to cause cancer, and birth defects or
other reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)
SAVE THESE
INSTRUCTIONS.
GROUNDING
TO PREVENT
ELECTRIC SHOCK
AND DEATH FROM INCORRECT
GROUNDING WIRE
CONNECTION:
Check with a qualied electrician
if you are in doubt as to whether
the outlet is properly grounded.
Do not modify the power cord
plug provided with the pump.
Never remove the grounding
prong from the plug. Do not use
the pump if the power cord or
plug is damaged. If damaged,
have it repaired by a service
facility before use. If the plug will
not t the outlet, have a proper
Page 5For technical questions, please call 1-800-444-3353.SKU 4831
outlet installed by a qualied
electrician.
Grounded Pumps: Pumps with
Three Prong Plugs
3-Prong Plug and Outlet
Pumps marked with “Grounding 1.
Required” have a three wire cord
and three prong grounding plug. The
plug must be connected to a properly
grounded outlet. If the pump should
electrically malfunction or break down,
grounding provides a low resistance path
to carry electricity away from the user,
reducing the risk of electric shock. (See
3-Prong Plug and Outlet.)
The grounding prong in the plug is 2.
connected through the green wire inside
the cord to the grounding system in the
pump. The green wire in the cord must
be the only wire connected to the pump’s
grounding system and must never be
attached to an electrically “live” terminal.
(See 3-Prong Plug and Outlet.)
The pump must be plugged into an 3.
appropriate outlet, properly installed and
grounded in accordance with all codes
and ordinances. The plug and outlet
should look like those in the preceding
illustration. (See 3-Prong Plug and
Outlet.)
Extension Cords
Grounded1. pumps require a three wire
extension cord. Double Insulated
pumps can use either a two or three wire
extension cord.
As the distance from the supply outlet 2.
increases, you must use a heavier gauge
extension cord. Using extension cords
with inadequately sized wire causes a
serious drop in voltage, resulting in loss
of power and possible pump damage.
(See Table A.)
The smaller the gauge number of the 3.
wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry
a higher current than a 16 gauge cord.
(See Table A.)
When using more than one extension 4.
cord to make up the total length, make
sure each cord contains at least the
minimum wire size required. (See Table
A.)
If you are using one extension cord for 5.
more than one pump, add the nameplate
amperes and use the sum to determine
the required minimum cord size. (See
Table A.)
If you are using an extension cord 6.
outdoors, make sure it is marked with the
sufx “W-A” (“W” in Canada) to indicate it
is acceptable for outdoor use.
Make sure the extension cord is properly 7.
wired and in good electrical condition.
Always replace a damaged extension
cord or have it repaired by a qualied
electrician before using it.
Protect the extension cords from sharp 8.
objects, excessive heat, and damp or
wet areas.
Page 6 For technical questions, please call 1-800-444-3353. SKU 4831
RECOMMENDED MINIMUM WIRE GAUGE
FOR EXTENSION CORDS* (120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
EXTENSION CORD
LENGTH
25’ 50’ 75’ 100’ 150’
0 – 2.0 18 18 18 18 16
2.1 – 3.4 18 18 18 16 14
3.5 – 5.0 18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - -
TABLE A
* Based on limiting the line volt-
age drop to ve volts at 150% of
the rated amperes.
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
V~
Volts Alternating Current
A
Amperes
n
0
xxxx/min.
No Load Revolutions per Minute
(RPM)
Page 7For technical questions, please call 1-800-444-3353.SKU 4831
SPECIFICATIONS
Electrical Input 120 V~ / 60 Hz / 6 W
Barrel Dimensions 16” Dia. x 12” H
Handle Height 30-
1
/
2
”
UNPACKING
When unpacking, make sure that all
parts shown on the parts list near the end
of this manual are included. If any parts are
missing or broken, please call Harbor Freight
Tools at 1-800-444-3353 as soon as possible.
ASSEMBLY AND OPERATING
INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set up
or use of this product.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Unplug the pump from its
electrical outlet before
assembling or making any
adjustments to the pump.
Note: For additional information regarding the
parts listed in the following pages, refer
to the Assembly Diagram near the end of
this manual.
FIGURE 1
Handle Bracket
Handle
Screw (9)
1. Fit the Handle (7) to the Handle Bracket
and secure with a Screw (9), Washer
(11), and Nut (12). See FIGURE 1.
FIGURE 2
Screw (10)
Barrel (1)
Pump Body (2)
2. Attach the Pump Body (2) to the Barrel
(1) using Screws (10), Washers (11), and
Nuts (12). See FIGURE 2.
REV 04a, 04b
Page 8 For technical questions, please call 1-800-444-3353. SKU 4831
FIGURE 3
Barrel (1)
Pump Body (2)
Electric Pump (4)
Plastic Tube (3)
Cord
(5)
3. Line the inside of the Barrel (1) with
the Polypropylene Liner (13). (Liner not
shown in Figure 3.)
Connect one end of the Plastic Tube (3) 4.
to the Electric Pump (4). Insert the other
end so it ts tightly into the Pump Body
(2).
Run the Cord (5) from the Electric Pump 5.
(4) out of the Barrel (1) but do not plug it
in yet.
Fill the Barrel (1) approximately 60% full 6.
with water.
WARNING
To prevent serious injury, ensure that
the power cord hangs in such a way that
water will drip off the cord before reaching
the outlet (referred to as a drip loop).
Make sure your feet and hands are 7.
dry, then plug in the power cord. The
pump will draw water from the barrel
and recycle it through the pump spigot,
creating a soothing sound.
When you are nished using the unit, 8.
with dry hands and feet, unplug the
pump.
WARNING! Unplug the unit from the
power source before touching the
water to make any adjustments to the
pump, electric pump, cords, lines, or
the Barrel.
REV 04a
Page 9For technical questions, please call 1-800-444-3353.SKU 4831
MAINTENANCE AND
SERVICING
Procedures not specically
explained in this manual must
be performed only by a qualied
technician.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Unplug the pump from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
TO PREVENT SERIOUS INJURY
FROM PUMP FAILURE:
Do not use damaged equipment.
If abnormal noise or vibration
occurs, have the problem
corrected before further use.
Cleaning, Maintenance, and
Lubrication
BEFORE EACH USE,1. inspect the
general condition of the pump. Check
for loose hardware, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical wiring,
and any other condition that may affect
its safe operation.
Periodically, remove the Electric Pump 2.
(4) and clean any dirt or debris from the
water intake.
Wipe down the cast iron Pump (2) with a 3.
lint free cloth.
4. WARNING! If the supply cord
of this power pump is damaged, it
must be replaced only by a qualied
service technician.
Page 10 For technical questions, please call 1-800-444-3353. SKU 4831
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
PARTS LIST
Part Description Qty.
1 Barrel 1
2 Pump Body 1
3 Plastic Tube 1
4 Electric Pump 1
5 Cord 2
6 Adapter 1
7 Handle 1
8 Pump Cover 1
9 Screw M6x18 2
10 Screw M8x38 4
11 Washer M8 4
12 Nut M8 4
13 Polypropylene Liner 1
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
Note: The hardware (Parts 9, 10, 11, 12) and the Polypropylene Liner (13) are not shown.
REV 04a
Page 11For technical questions, please call 1-800-444-3353.SKU 4831
ASSEMBLY DIAGRAM
REV 04a
1
2
3
4
5
6
7
8
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
One Stop Gardens 4831 Assembly And Operating Instructions Manual
- Type
- Assembly And Operating Instructions Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Central Hydraulics 92038 User manual
-
Harbor Freight Tools 95781 User manual
-
-
Pittsburgh Automotive Item 98076 Owner's manual
-
-
Chicago Electric 98841 Set Up And Operating Instructions Manual
-
Central Pneumatic 93785 Owner's manual
-
-
-