Page is loading ...
ASSEMBLY & OPERATING INSTRUCTIONS
92485
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web Site at www.harborfreight.com
Copyright
©
2004 by Harbor Freight Tools
®
. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
®
WROUGHT IRON
BIRD BATH
SKU 92485 For technical questions please call 1-800-444-3353. Page 2
THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please
complete the owner’s record below:
Model
______________ Serial No._____________ Purchase Date_______________
SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the
entire manual to become familiar with the unit BEFORE you begin assembly.
This beautiful Birdbath invites birds of all kinds into your garden. It has two stakes for easy
anchoring.
Technical Specifications
Material: Wrought Iron Stand with copper bird bath bowl
Bowl Diameter: 11-3/4” x 2-1/8” deep
Mounting Hole Diameter: 8 mm x 1-1/4” standard thread
Height: 46-1/4”
Weight: 2.6 Lbs.
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injury.
2. Observe work area conditions. Keep work area well lit.
3. Check for damaged parts. Before using any product, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for any broken or damaged parts and any other conditions that may affect its operation.
Replace or repair damaged or worn parts immediately.
4. Replacement parts and accessories. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
5. Always check hardware and assembled parts after assembling. All connections should be
tight and hardware tightened.
6. Keep children away. Children must never be allowed to play or climb on the Bird Bath.
7. Dress properly. Gloves and nonskid footwear are recommended when assembling the
Wrought Iron Bird Bath. Wear restrictive hair covering to contain long hair.
8. Use eye protection. Always wear ANSI approved impact safety goggles when assembling the
Bird Bath.
9. There are certain applications for which this Bird Bath was designed. Do not modify this Bird
Bath and do not use this Bird Bath for a purpose for which it was not intended.
SKU 92485 For technical questions please call 1-800-444-3353. Page 3
10. Do not assemble or set up the Bird Bath if under the influence of alcohol or drugs. Read
warning labels on prescriptions to determine if your judgement or reflexes are impaired while
taking drugs. If there is any doubt, do not assemble or set up the Bird Bath.
11. This is erected by driving the 2 legs into the ground. Ground does not have to be “flat and
level”. The stand should be checked for vertical with a level.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking the Wrought Iron Bird Bath, check to make sure the following parts are included. If
any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.
Assembly/ Operation
Your Wrought Iron Bird Bath will require complete assembly. It is important that you read the entire
manual to become familiar with the product BEFORE you assemble and use the Bird Bath. Before
assembling the Bird Bath be sure that you have all parts described in the Parts List and Assembly
Diagram located on the last page of this manual.
1. Thread one end of the Stud (C) to the threaded screw located on the Copper Basin (A)-see
Figure 1.
2. Attach Stand (B1) to Stand (B2) by inserting the small prong on Stand (B1) into the end of
Stand (B2)-see Assembly diagram.
3. Thread the Stud (C) and Basin (A) down onto the threaded extension on Stand (B2)-see
Figure 1 and Assembly diagram. Do not over tighten the Stud (c) as you thread it into place.
4. Locate the desired spot in your garden to place the Bird Bath. Before inserting the Bird Bath
into the ground, make certain that no cables or electrical wires are in the path of the
stakes. Insert the stakes at the bottom of Stand (B1) down into the ground. Make certain that
the stakes are inserted to near the first rung on the Stand (B1).
Figure 1
Basin (A)
Stud (C)
Stand (B2)
SKU 92485 For technical questions please call 1-800-444-3353. Page 4
Parts List
Part # Description Quantity
A Basin 1
B1 Stand 1
B2 Stand 1
C Stud 1
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
Assembly Diagram
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
A
B2
B1
C
/
