Steris Cmax X-Ray Image-Guided Surgical Table Operating instructions

PS00000507

Revision A

CMAX™ X-Ray

Image-Guided Surgical Table

Operator Manual

1 — A Word from STERIS

2

PS00000507_A CMAX™ X-Ray Operator Manual

A Word from STERIS

1.1 Introduction

Thank you for choosing this STERIS product. STERIS is committed to ensuring your continued satisfaction. This manual

contains important information on proper use and maintenance of the STERIS CMAX™ X-Ray table.

IMPORTANT: A listing of the Safety Precautions to be observed when operating and servicing this equipment can be found in

Section 2, Safety Precautions. Do not operate or service the equipment until you have been trained on this information.

These instructions provide crucial information on how to prevent injuries and property damage that could result from

improper maintenance of the CMAX™ X-Ray table. This manual should be retained in a conveniently accessible area for

quick reference.

Any alteration of the surgical table not authorized or performed by STERIS which could affect operation will void the

warranty, could jeopardize operator and patient safety, could adversely affect efficacy, and could violate national,

federal, state or local regulations.

Intended Use

CMAX™ X-Ray surgical tables are medical devices intended to support and position patients during surgical procedures

carried out in an operating room.

Indications for Use

CMAX™ X-Ray surgical tables have no indication for use, which means that these medical devices are not used to

diagnose, prevent, monitor, treat, alleviate, compensate, replace, modify or control any clinical condition of a patient.

Contraindication – Undesirable Side-Effect – Residual risks

There is no contraindication, undesirable side-effect or residual risks associated with CMAX™ X-Ray surgical tables. All

safety instructions related to the use of these medical devices are listed in Section 2, Safety Precautions.

Patient Target Group

CMAX™ X-Ray surgical tables are not directed to a particular patient population: these medical devices are supposed to

suit any type of patient, regardless of age, anatomy, gender, etc. However, for the safety of the product, weight limits

of patients are indicated in this user manual.

Intended User

CMAX™ X-Ray surgical tables must be used only by qualified personnel who are authorized to practice in the healthcare

facility. These medical devices shall be operated in a controlled environment by fully trained personnel. This product

was developed for surgeons, anesthetists, nurses etc. and is for use in operating rooms, pre- anesthesia rooms, or

recovery rooms.

Essential Performance

CMAX™ X-Ray surgical tables shall support a patient without unwanted movement in a single-fault condition.

1 — A Word from STERIS

3

Operator Manual CMAX™ X-Ray PS00000507_A

Intended Lifetime

The intended lifetime of CMAX™ X-Ray surgical tables is set at 10 years, provided that the conditions of use, the

cleaning and maintenance instructions listed in this user manual are correctly followed.

1.2 Waste Disposal

WARNING

DISPOSAL HAZARD

This product contains materials which may require disposal through appropriately licensed and permitted

hazardous waste management firms.

CAUTION

POSSIBLE EQUIPMENT DAMAGE

Use of incorrect hydraulic oil may severely damage the table and/or cause malfunction. Contact STERIS

for proper hydraulic oil.

The following materials may be contained within the table. When disposing of the table or its parts, ensure the proper

disposal of hazardous and other regulated waste in compliance with federal, state and local regulations.

Lead Acid (Pb/H 2SO 4): gelled cell batteries located in the table base at the head-end side of the table. Approximate

weight 21 lbs. (9.5 kg).

Lead (Pb) in Solder: contained in solder on circuit boards and in some miscellaneous wire connections. Minute

amounts.

Electronic and Electrical Parts: not known to require special disposal at date of this manual.

Parts Material: made from aluminum (Al), steel (Fe), cast iron (Fe), copper (Cu), and copper alloys (Cu/x), plastic,

synthetic rubber, plating (Cr, Ni, Zn, Au), Polyvinylchloride (PVC), and adhesives not known to require special disposal

methods at date of this manual.

Hydraulic Oil: contained in hydraulic components located in the base, column, tabletop, and hydraulic system lines and

hoses.

1.3 Service Information

A thorough preventive maintenance program is essential for safe and proper unit operation. This manual contains

maintenance schedules and procedures which should be followed for satisfactory equipment performance.

Only STERIS-trained personnel should attempt to perform maintenance on the table, to avoid personal injury, improper

equipment performance, invalidation of the equipment warranty or other costly damage.

Customers are encouraged to contact STERIS concerning our comprehensive preventive maintenance program. Under

the terms of this program, preventive maintenance, adjustments and replacement of worn parts are provided on a

scheduled basis to help ensure optimal equipment performance and help avoid untimely or costly interruptions. STERIS

maintains a global staff of well equipped, factory-trained technicians to provide these services, as well as expert repair

services. Please contact STERIS for details.

1 — A Word from STERIS

4

PS00000507_A CMAX™ X-Ray Operator Manual

1.4 Contact Information

Manufactured by:

STERIS SAS

116 Avenue de Magudas

33185 Le Haillan

FRANCE

TEL: (+33) 5 56 93 94 94

www.steris.com

Class I Equipment

Type B Applied Part

Splash-Proof Equipment (enclosed equipment protected

against splashing water, IPX4)

Equipment not suitable for use in the presence of a

flammable anesthetic mixed with air or oxygen or nitrous

oxide.

Suitable for intermittent operation 3 min/hr.

The base language of this document is ENGLISH. Any translations must be made from the base

language document.

5

Operator Manual CMAX™ X-Ray PS00000507_A

TABLE OF CONTENTS

Section Number Description Page

1 A Word from STERIS...................................................................................................................................... 2

1.1 Introduction................................................................................................................................. 2

1.2 Waste Disposal ........................................................................................................................... 3

1.3 Service Information .................................................................................................................... 3

1.4 Contact Information ................................................................................................................... 4

2 Safety Precautions ........................................................................................................................................ 6

3 Symbols Used............................................................................................................................................... 14

4 Component Identification ........................................................................................................................... 19

4.1 Overview ................................................................................................................................... 19

5 Operating Instructions ................................................................................................................................ 24

5.1 Operating the Table.................................................................................................................. 24

5.2 Operating the CMAX™ X-Ray Main Hand Control .................................................................. 30

5.3 Joystick Operation..................................................................................................................... 40

5.4 ALS™ (Auto Limit Sensors) ....................................................................................................... 43

5.5 Backup Control (Auxiliary Keypad)........................................................................................... 44

5.6 Examples of Patient Positioning.............................................................................................. 45

5.7 Mounting the Various Adaptable Accessories Onto the Carbon Tabletop ........................... 49

6 Routine Maintenance .................................................................................................................................. 50

6.1 Maintenance – General Information ....................................................................................... 50

6.2 Cleaning and Disinfection......................................................................................................... 50

6.3 Maintenance Schedule ............................................................................................................. 54

6.4 CMAX™ X-Ray Spare Parts List ............................................................................................... 55

7 Troubleshooting........................................................................................................................................... 56

7.1 General Troubleshooting Information ..................................................................................... 56

7.2 List of Software Errors ............................................................................................................. 57

7.3 Extension Does Not Lock or Has Too Much Play ................................................................... 57

7.4 The Table Does Not Move........................................................................................................ 58

7.5 Table Remains in Battery Mode When Power Cord is Connected ........................................ 58

7.6 The Table Will Not Switch On .................................................................................................. 58

7.7 The Table Will Not Switch to Unlock Position ........................................................................ 59

8 Electromagnetic Environment.................................................................................................................... 60

9 Commissioning Record ............................................................................................................................... 63

2 — Safety Precautions

6

PS00000507_A CMAX™ X-Ray Operator Manual

Safety Precautions

The following Safety Precautions must be observed when operating or servicing this STERIS equipment. WARNING

indicates the potential for personal injury and CAUTION indicates the potential for damage to equipment. For emphasis,

certain Safety Precautions are repeated throughout the manual. It is important to review ALL Safety Precautions

before operating or servicing the unit.

NOTE: Disregarding this safety information is considered ABNORMAL USE of this product.

NOTE: Any serious incident involving this medical device must be reported to STERIS and the competent authority of

the member state in which the user and/or patient is established.

WARNING

RISK OF INJURY

The modification of this medical device without manufacturer authorization is prohibited.

Pinch Points

WARNING

PINCHING HAZARD

When floating is enabled, moving the floating tabletop can cause pinch points which can injure the patient

or the surgical team.

To avoid serious injury, keep limbs, fingers and other body areas clear of all pinch points when positioning

the table.

When manually positioning table sections, stay clear of potential pinching hazards.

Floor Lock

WARNING

PERSONAL INJURY HAZARD

Tabletop functions are available even if table floor locks are NOT engaged. Lock table before positioning

the patient and starting the surgical procedure.

Do not try to move the table when it is locked.

Make sure the table is stable before engaging the floor locks. If the table is unstable move it to a flatter

surface then engage the floor locks.

2 — Safety Precautions

7

Operator Manual CMAX™ X-Ray PS00000507_A

Patient must be secured to the table in accordance with recommended positioning practices.

Unanticipated patient or table movement could result in death or serious injury

Moving the Table with a Patient Aboard

WARNING

RISK OF PERSONAL INJURY & EQUIPMENT DAMAGE

The table can only be unlocked if the floating tabletop is not activated.

The table is intended to be used for moving or adjusting patients in the operating room. It is not to be

used to transport patients outside the operating room. When moving or adjusting the table with a patient

aboard, the following conditions shall be met:

●The tabletop must be leveled and centered over the column.

●Only lateral slide up to 50mm (2”) is allowed.

●The tabletop shall be lowered below 900mm (35”).

●The patient shall be in normal orientation and the total weight (patient + accessory) shall not exceed

230kg (507lbs).

●The headrest (BF755) may be mounted to the tabletop.

Make sure the battery is properly charged before moving the table.

Before moving the table, ensure its path is clear of obstruction. The table is not intended to cross

threshold or go up or down steps. Always move the table very carefully.

Do not leave objects on the base as they may fall off during motorized manoeuvres and cause a jam

when lowering the column’s sliding covers.

Handling the Surgical Table

WARNING

RISK OF PERSONAL INJURY & EQUIPMENT DAMAGE

Avoid rough handling of the surgical table during operation. Do not exert excessive lateral loads on it, do

not pull or push the surgical table with the accessories or with the rails.

Handle the remote control and the override system with care. Do not press the keypad with too much

force.

2 — Safety Precautions

8

PS00000507_A CMAX™ X-Ray Operator Manual

Handle the cables with care when connecting or disconnecting the remote control, the joystick, or the

power cord set.

Do not sit on either end of the table, especially when the tabletop is not centered, as this can cause the

table to become unstable and tip.

Do not stand on the base of the surgical table as it can damage the covers.

Pay attention to the power cord when it is connected to the surgical table as it is a tripping hazard. Route

the power cord to the receptacle to minimize the possibility of personnel tripping. Disconnect the cable

before moving the table.

Weight Capacity

WARNING

RISK OF PERSONAL INJURY & EQUIPMENT DAMAGE

Do not exceed a patient + accessory combined weight of 230 kg (507 lbs) for the standard described

positions and follow the indications and warnings provided.

The use of certain extensions may lower the patient + accessories max weight. When extensions are

installed on the CMAX™ X-Ray surgical table, consult the user manuals for these extensions to find out if

there are weight restrictions related to their use.

Certain positions may cause the tabletop to be significantly off-centered from the column. In these

situations, ensure that there is sufficient stability for the type of surgical procedure requirements.

For all other uses, please contact our network for advice. If you are working intensively on the patient’s

chest, we recommend that you bring the tabletop back to a centered position on the column.

Positioning the Patient

WARNING

RISK OF INJURY

The positions described in this manual are given purely as examples. The accessories required are not

always shown. Under no circumstance should they replace the instructions given by the surgical team in

charge of the patient.

Ensure the stability of the patient and the table when making combined position.

2 — Safety Precautions

9

Operator Manual CMAX™ X-Ray PS00000507_A

Secure the patient properly (ex. using straps), especially when the table is inclined or tilted.

Long surgical procedures can cause tissue compression over bony prominence on patients and result in

tissue ischemia, pressure injury, and post operative problems. Monitor and reposition patients during

surgical procedures, or use patient positioning aids to alleviate areas of high pressure and allow tissue

reperfusion for extended procedures.

Connections

WARNING

RISK OF PERSONAL INJURY & EQUIPMENT DAMAGE

The wire terminals of the hand control and joystick are equipped with soft locks that lock into place. Do

not pull on the hand control or Joystick to disconnect them.

The E-Serve connection is only to be used by STERIS service team and with material approved by STERIS.

Never try to connect a device not supplied by STERIS or approved for use with CMAX™ X-Ray to the

surgical table.

Always use the power cord provided by STERIS.

The operator must not make physical contact with the patient while plugging or unplugging the remote

control or joystick, or while handling connectors on these devices.

Potential Equalization Conductor

WARNING

RISK OF PERSONAL INJURY & EQUIPMENT DAMAGE

Connect together potential equalization conductors to avoid problems with differing potentials across

networks.

Potential equalization conductors protect patients from electric shock during procedures where even

small potentials may cause harm.

When a potential equalization conductor is connected, the table MUST NOT be used with a defibrillator.

When using potential equalization conductors in an electro-medical system, this system must meet IEC

60601-1 requirements.

2 — Safety Precautions

10

PS00000507_A CMAX™ X-Ray Operator Manual

Antistatic Link

WARNING

RISK OF PERSONAL INJURY & EQUIPMENT DAMAGE

If antistatic connection is necessary, use only the pads that have been specially developed for this

product. Put the patient in direct contact with these pads and use the table on an antistatic floor, or

connect it to an equipotential cable using the socket designed for it.

Electrical Safety

WARNING

RISK OF PERSONAL INJURY

To prevent any risk of electric shock, the CMAX™ X-Ray should only be connected to a grounded power

supply system.

The CMAX™ X-Ray must always be positioned so that the power cord can be disconnected easily when

connected to the table.

Disconnecting the power cord isolates the CMAX™ X-Ray table from supply mains.

It is preferable to use the batteries instead of the mains if the protective ground in the operating room is

in doubt.

The use of high-frequency surgical equipment, cardiac defibrillators, and cardiac defibrillator monitors in

association with the CMAX™ X-Ray table creates a risk of burns, explosion, or electrical shock.

In case of any damage to the power supply, power cord, plug, or IEC receptacle, do not connect the

equipment and immediately contact STERIS technical support.

Accessories

WARNING

RISK OF PERSONAL INJURY & EQUIPMENT DAMAGE

If accessories made by other manufacturers are used, it is the user’s responsibility to ensure they are

compatible with CMAX™ X-Ray and that they do not create a hazard to the patient and the surgical team.

Before connecting accessories to the surgical table, make sure they are not damaged.

2 — Safety Precautions

11

Operator Manual CMAX™ X-Ray PS00000507_A

The end user must ensure that the intended use and the conditions of use (including the safe working

load) of these accessories made by other manufacturers are compatible with the claims of CMAX™ X-Ray

surgical tables.

Emergency Mode

WARNING

RISK OF PERSONAL INJURY & EQUIPMENT DAMAGE

Use the override system only in emergency mode. When the override system is used, the other control

systems, including the main hand control, are automatically switched off. Since the ALS sensors are

deactivated, ensure you look out for potential section conflicts when moving the tabletop. The pre-

selected patient orientation set as default is the normal orientation; there is no reverse orientation. There

is no immobilization warning LED: you must engage the table locks before moving the tabletop. When

using the override system, always make sure the surgical table is stable and the table locks are engaged

before moving the tabletop, especially when moving the tabletop to greatly off-centered positions.

Cleaning

WARNING

RISK OF PERSONAL INJURY & EQUIPMENT DAMAGE

Do not use chlorine-based products or other products containing chlorine derivatives; these can cause

excessive corrosion.

Ensure protective covers are properly installed over receptacles to prevent fluids from reaching the

receptacles. After cleaning the table, ensure no residual water remains near the receptacles.

Before cleaning the table, make sure it is switched off and the protective covers are properly installed

over the receptacles.

Do not immerse the hand control or the joystick and do not spray cleaning products directly onto the

receptacles.

Environmental Conditions

• Transport / storage: temperature 0°C - 50°C (32°F - 122°F), humidity 10-85% non-condensing, pressure 500-

1060 hPa, table on castors, battery fuses removed.

• Use: temperature 10°C-40°C (50°F - 104°F), humidity 10-75% non-condensing, pressure 800 - 1060 hPa (23.6 –

31.3 inHg).

• Floor surface punching pressure: 0.13 kg/cm² (13 Pa / 1.85 psi) with a patient + accessories load of 270kg (595

lbs).

• Local pressure on the floor: 15.59 kg/cm² (1,529 MPa / 222 psi) with a patient + accessories load of 270kg (595

lbs).

2 — Safety Precautions

12

PS00000507_A CMAX™ X-Ray Operator Manual

WARNING

RISK OF PERSONAL INJURY & EQUIPMENT DAMAGE

Do not use the table in the presence of flammable anesthetic gas, or in areas subject to explosive risks.

CMAX™ X-Ray must not be used in the vicinity of strong magnetic fields (MRI environment).

CMAX™ X-Ray and associated extensions and accessories are not intended to operate in an oxygen rich

environment.

CMAX™ X-Ray and associated extensions and accessories are not intended for outdoor use, and shall not

be exposed to high humidity for an extended time.

X-Ray Radiation

WARNING

RISK OF INJURY

The surgical table's materials, when exposed to X-Ray radiation, can produce and expel harmful radiation

to the environment that is potentially harmful to users. Radiological protection devices should therefore

be worn by users when using X-Ray equipment with CMAX™ X-Ray surgical tables.

Maintenance

WARNING

RISK OF INJURY

The safety, reliability, and proper operation of the surgical table can only be ascertained and granted by

STERIS. Repair and adjustments should only be assigned to STERIS technicians or STERIS-approved

technicians.

Observe the maintenance schedule recommended by STERIS and described in this document.

Never try to adjust or repair the surgical table yourself.

No repair should be undertaken on CMAX™ X-Ray surgical tables until electrical power is switched off,

locked out and tagged out.

During maintenance and repair, only original parts should be used.

No part of the surgical table shall be serviced or maintained while in use with the patient.

2 — Safety Precautions

13

Operator Manual CMAX™ X-Ray PS00000507_A

Hand control storage

CAUTION

EQUIPMENT DAMAGE

Hang the hand control from side rail of the table when not in use to avoid possible damage to the control.

Handle the hand control and the associated cable with care.

Electromagnetic Compatibility

CAUTION

EQUIPMENT DAMAGE

If the table is used close to other electrical equipment, ensure that these comply with the regulations

regarding electromagnetic compatibility.

If high frequency equipment (such as a defibrillator) is being used, make sure to follow the manufacturer’s

instructions carefully.

FCC Part 15: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

3 — Symbols Used

14

PS00000507_A CMAX™ X-Ray Operator Manual

Symbols Used

Table 3-1. Main Hand Control

Symbol Definition

Floor Locks – Locked / Unlocked

Trendelenburg / Reverse Trendelenburg

Up / Down

Left Tilt / Right Tilt

Return to Level, Origin Position

Patient Orientation – Normal / Reverse

Memory Function

Menu Actions

Menu Selection

Stop All Table Articulation

Table 3-2. TFT Screen Pictograms

Symbol Definition

Floor Lock Engaged

Enable Floating: Tabletop Brake On When Joystick is

Active

Enable Floating: Table Brake on when hand control is

active.

Floor Lock Released

3 — Symbols Used

15

Operator Manual CMAX™ X-Ray PS00000507_A

Table 3-2 TFT Screen Pictograms (Continued)

Symbol Definition

Floating in Progress: Tabletop Free in Transverse +

Longitudinal Direction

Please Wait - Cycle in Progress (e.g. Locking/Unlocking)

Control Interface Active: Joystick / Bluetooth / Hand

Control / E-serve

Bluetooth Joystick Battery Charge Status

Bluetooth Joystick Battery Discharge Status

Alarm Condition – Refer to Troubleshooting Section or

Contact STERIS Technical Department

Table 3-3. Override Control / Joystick

Symbol Definition

Lock / Unlock Tabletop Float

Trendelenburg / Reverse Trendelenburg

Height / Down

Left Tilt / Right Tilt

Select Locked / Unlocked

Powered Backup Control Validation (in Combination with

the Desired Movement)

Start Up Table/Joystick In Bluetooth Mode

3 — Symbols Used

16

PS00000507_A CMAX™ X-Ray Operator Manual

Table 3-3 Override Control / Joystick (Continued)

Symbol Definition

Return to Level

Stop All Table Articulation

Table 3-4. Connection Panel

Symbol Definition

Main Hand Control (Wired)

E-SERVE Serial Port: Reserved for STERIS Use

IMPORTANT: This port is intended for use by STERIS or

STERIS-trained personnel for maintenance procedures only. It

must not be used to move the table during a surgical

procedure.

Joystick (Wired/Bluetooth®)

Accessory port

IMPORTANT: This port must not be used with the CMAX™ X-

Ray or any of its accessories. Do not plug any CMAX™ X-Ray

accessory into it.

Table 3-5. Mobile Base and Packaging Labels

Symbol Definition Symbol Definition

Warning: Read the

Accompanying Documents Hz Frequency Rating of Unit

Attention, Consult Manual

for Further Instructions VA Power Rating of Unit (Volt-

Ampere)

Equipotential

port/outlet/socket

Medical Device

WEEE Directive: the

Product Must Be Recycled

Do Not Wash With

Machine

Name and Address of

Manufacturer

ETL Certification —

Compliance to North

American Safety Standards

3 — Symbols Used

17

Operator Manual CMAX™ X-Ray PS00000507_A

Table 3-5 Mobile Base and Packaging Labels (Continued)

Symbol Definition Symbol Definition

Protection from Electric

Shock Class 1, Type B

Atmosphere Pressure

Limitation

Splash-Proof Equipment Humidity Limit

Date of Manufacture

YYYY/MM/DD

Temperature Limit

/ VDC Direct Current No Stacking for CMAX™ X-

Ray

/ VAC Alternating Current This Way Up

1-4

150830-685 Operator Manual Safety Precautions

CHARGE BATTERY

INTELLI POWER

Symbol Definition

Type B Equipment

Protective Earth Ground

Equipotentiality

Electric Shock Hazard

Control Power ON

Control Power OFF

Powered By AC

Attention, Consult Manual for Further Instructions

AAmperage Rating of the Unit

VVoltage Rating of the Unit

~Alternating Current

Hz Frequency of the Unit

WPower Rating

SNSN

SN Serial Number of the Unit

IPX4IPX4

IPX4 Splash-Proof Equipment

Intellipower® Dual Power System Power Panel

(Battery Charge/Discharge Status)

Powered By Battery

Symbols

on Table

Following is a key to symbols on the Cmax Surgical Table.

- OR -- OR -

- OR -

0

BATTERY

Protective Earth (Ground) Fragile, Handle with Care

Product Reference Handle with Care

Serial Number Safety Warning

Batch Number Caution

VVoltage Rating of Unit IPower Supply ON

AAmperage Rating of the

Unit OPower Supply OFF

Ah Energy Unit of the

Batteries (Ampere Hour)

3 — Symbols Used

18

PS00000507_A CMAX™ X-Ray Operator Manual

Table 3-6. Label Definition

Label Definition

Purpose: Indicates a risk of injury from items stored on

the table base

Purpose: Indicates maximum weight capacity

4 — Component Identification

19

Operator Manual CMAX™ X-Ray PS00000507_A

Component Identification

4.1 Overview

4 — Component Identification

20

PS00000507_A CMAX™ X-Ray Operator Manual

1 — Mobile base 7 – 28.5x9.4mm (1.10x0.35”)

Standard accessory rails

13 — Identification label

2 — Column 8 — Connection panel 14 — Battery fuse

3 — Floating tabletop 9 — Carbon tabletop rail accessory 15 — Equipotential plug

4 — Joystick (floating tabletop

control)

10 — Override control 16 — Battery status

5 — Head section interface 11 — Electrical characteristics label 17 — Mains power cable

6 — Main hand control 12 — Mains connection panel

Characteristics

The CMAX™ X-Ray operating table is equipped with a carbon fiber floating tabletop offering exceptional radiological

access.

The CMAX™ X-Ray is suitable for image-guided surgical procedures and has been designed to support patient +

accessory weights of up to 230 kg (507.1 lbs) in multiple position as described in this manual.

The table is controlled by an ergonomic hand control or the joystick in dual-mode (wired/Bluetooth). The innovative

integrated power supply allows the user to choose whether to operate the table on battery or main power. Most table

articulations are powered, whereas the floating tabletop slides manually. E-Serve™ allows for remote diagnostics and

maintenance via computer by approved STERIS technicians (errors, fault log).

The integrated ALS™ linear and angular position sensors prevent collisions between the powered sections of the table

and the floor.

Page is loading ...

Steris Cmax X-Ray Image-Guided Surgical Table Operating instructions

Steris Cmax X-Ray Image-Guided Surgical Table Operating instructions

Related papers

Other documents